B112V2/B110V2 Subwoofer Quick Start Guide
TABLE OF CONTENTS About Revel Performa3V2 Subwoofers.................................................................................................................................... 2 B112V2/B110V2 Overview........................................................................................................................................................ 3 Subwoofer Placement Considerations..................................................................................................................
B112V2/B110V2 OVERVIEW (Note: B112V2 and B110V2 rear panels are identical) Input Connectors (Balanced XLR) Power Switch Power Cord Connector Input connectors: Connect these to the outputs of a stereo preamp or connect a surround processor's subwoofer output to either the left or right input. Balanced (XLR) and unbalanced (RCA) connectors are available. The inputs are 0dBV nominal to +12dBV max unbal/+18dBV max bal. The XLR input is pin 2 hot.
SUBWOOFER PLACEMENT CONSIDERATIONS When using subwoofers within the limited confines of a typical home theater room, the reflections, standing waves and absorptions within the room will create peaks and dips in the bass response that can vary greatly depending on where the listeners are located in the room – a listener seated in one location may hear an overabundance of bass created by a response peak at that location, while another listener only a few feet away may hear far less bass due to a response dip
Rooms with multiple seating rows PLACING FOUR SUBWOOFERS Placing one subwoofer in a front corner and the other subwoofer in the rear corner on the same side will produce the most consistent bass performance throughout multiple seating rows. When installing four subwoofers, place each one in a room corner. In rooms with more than four corners, use the four corners closest to the listening area.
MAKING CONNECTIONS CAUTION: Never make or break connections unless all system components are powered off. CONNECTING TO AN AV SURROUND RECEIVER OR PROCESSOR WITH AN INTERNAL CROSSOVER If you are connecting to a surround processor with a low-pass filtered subwoofer output, connect the subwoofer as shown below. You can make either a balanced (XLR) or unbalanced (RCA) connection to either the subwoofer’s left or right input connector.
CONNECTING TO A STEREO RECEIVER, AMPLIFIER OR PREAMPLIFIER If you are connecting to a stereo device, connect the subwoofer as shown below. Stereo components rarely have subwoofer outputs. Use them if they are available; otherwise, be sure to use a Y-connector for the left output and one for the right output, connecting the subwoofer input to one side of each Y and the input for the left or right main speaker amplifier to the other side of the Y for proper main speaker operation.
CONNECTING MULTIPLE SUBWOOFERS When installing more than one Performa3V2 subwoofer, connect “Y” connectors to the receiver or processor’s outputs. If your source component has two subwoofer output jacks you can connect up to four subwoofers as illustrated on this page. Be sure to set up and adjust each subwoofer PEQ separately, then adjust all of the subwoofer levels and crossover frequencies together to blend to the main speaker systems.
TRIGGER AND POWER CONNECTIONS Trigger In/Out Connectors If you want your subwoofer(s) to turn on along with another component that supplies a trigger voltage, use a mono 3.5mm cable (not supplied) to connect the 12V DC Trigger In connector to the trigger voltage out connector of the other component. To supply a trigger signal to an additional Performa3 subwoofer (or other triggerable device), use a mono 3.
SPECIFICATIONS B112V2/B110V2 Type: Powered subwoofer Low-frequency transducer: Coated paper/pulp cone (12" – B112V2; 10" – B110V2) with 50mm two-layer copper voice coil, vented ceramic 5 magnet assembly and vented die-cast aluminum frame Amplifier power: 1,000 watts (RMS), 2,000 watts (peak) Input sensitivity/impedance: 400mV (full power)/20k ohms (balanced); 14k ohms (unbalanced) Crossover frequency: 50Hz – 150Hz low-pass filter with LFE bypass Low Frequency Extension (Normal mode): -3dB at 34.
Торговая марка: Revel Назначение товара: Активная акустическая система Изготовитель: Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик Стрит 400, офис 1500 Страна происхождения: Индонезия Импортер в Россию: OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1 Гарантийный период: 1 год Информация о сервисных центрах: www.harman.com/ru Срок службы: 5 лет Срок хранения: не ограничен тел.
