C426Be Center Channel Loudspeaker Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS 1. Use only attachments/accessories specified by the manufacturer. 2. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 3. Refer all servicing to qualified service personnel.
UNPACKING THE C426Be Unpack the C426Be in the order of the illustrations below.
ABOUT REVEL PERFORMABe LOUDSPEAKERS C426Be OVERVIEW FEATURE HIGHLIGHTS 1" Beryllium Dome Tweeter with Acoustic Lens Waveguide • Beryllium Dome Tweeter • 5th-generation Acoustic Lens Waveguide Enclosure with 1"-Thick Panels and Extensive Internal Bracing • Deep Ceramic Composite (DCC™) Cone Midrange and Woofers • Wide bandwidth and dynamic range with minimal dynamic compression • High-order Crossovers with Film Capacitors and Air Core Inductors • Premium High-Gloss Finishes: Black, White, Walnut, Metal
LOUDSPEAKER PLACEMENT ADJUSTABLE FEET We recommend that you remove all obstructions between the loudspeaker and the primary listening position. For instance, a coffee table between the loudspeaker and the primary listening position will create reflections that will degrade timbre which can make film dialog more difficult to understand. Placing the loudspeakers near large objects may also cause unwanted reflections.
MAKING CONNECTIONS C426Be CONNECTIONS The C426Be features gold-plated binding posts that allow single-wire connection. CAUTION: Never make or break connections unless all system components are powered off. C426Be Connector Panel OBSERVE PROPER POLARITY Connect the amplifier’s positive (+) terminal to the positive (+) terminal on the loudspeaker; connect the amplifier’s negative (–) terminal to the negative (–) terminal on the loudspeaker.
C426Be SINGLE-WIRED CONNECTION Note: Do not remove the shorting straps between the speaker terminals. Single-wired connections are the most common. These are made between one pair of C426Be input terminals and one power amplifier output channel as shown below. Do NOT Remove Shorting Straps Amplifier (one channel shown) C426Be Connector Panel To make single-wired connections, connect one loudspeaker cable to the desired set of C426Be input terminals.
C426BE BI-AMPED CONNECTIONS CAUTION: Remove the shorting straps before making bi-amped connections. Failure to do so may cause damage to some power amplifiers. Note: When making bi-amped connections, both power amplifier channels must receive identical input signals from the associated preamp/processor. If the associated preamp/processor only has one connector for the center channel, a “Y” adapter is required.
OPTIMIZING PERFORMANCE CARING FOR YOUR LOUDSPEAKERS PORT PLUGS GRILLES Revel PerformaBe loudspeakers include a pair of foam port plugs, which are pre-inserted into the rear ports,and can be used to adjust the loudspeaker’s low-frequency performance in certain installation situations.
LIMITED WARRANTY Revel loudspeakers are warranted against defects. The duration of a warranty depends on the laws in the country in which it was purchased. Your local Revel retailer can help you determine the duration and coverage of your warranty. For more information please visit: REVELSPEAKERS.COM Please visit REVELSPEAKERS.COM for additional language support on the user manual. Veuillez visiter REVELSPEAKERS.COM pour obtenir le mode d’emploi en d’autres langues.
Торговая марка: Revel Назначение товара: Пассивная акустическая система Изготовитель: Харман Интернешнл Индастриз Инкорпорейтед, США, 06901 Коннектикут, г.Стэмфорд, Атлантик Стрит 400, офис 1500 Страна происхождения: Китай Импортер в Россию: OOO “ХАРМАН РУС СиАйЭс“, Россия, 127018, г.Москва, ул. Двинцев, д.12, к 1 Гарантийный период: 1 год Информация о сервисных центрах: www.harman.com/ru тел.
