Replacement Parts Guide

Form P-RG/RP/RBL, P/N 263984R2, Page 16
Heat Exchanger & Components - Applies to all Models (one heat exchanger per furnace
section; directional bafes apply as listed)










Heat Exchanger Directional Air Bafes
1) Models RG, CRG, RGB, CRGB, RP,
CRP, RPB, CRPB are equipped with a heat
exchanger directional air bafe assembly as
illustrated below (right).
NOTE: Beginning 1/2012, RPB units are built
with or without these heat exchanger bafes
depending on the CFM on the original order.
When replacing a heat exchanger, check to
see if the bafe assembly can be salvaged. If
the bafe assembly cannot be salvaged, it will
be necessary to order the parts (Codes 174-
179) in the quantities listed and assemble and
install replacement bafes.
2) Models HRG, HCRG, HRP, HCRP, HRGB,
HCRGB, HRPB, HCRPB, and the discharge
furnace only on Models HRPD, RGBL,
CRGBL, RPBL, and CRPBL are equipped
with only a rear top bafe support (Code 177)
and a rear top bafe (Code 179). If these
parts cannot be salvaged, order and install
replacements. These parts are not installed in
the replacement heat exchanger at the factory.
They must be ordered separately and installed
in the eld.
NOTE: See page 3 for no-longer-
manufactured models. Effective 9/11, HRP is
no longer available but a high CFM conversion
kit is available for Model RP units; see Code
181 above.
Heat Exchanger -
All Models



Heat Exchanger
Bafe in an
"H" Model and
"BL" Discharge
Furnace only
Heat Exchanger
Bafes - apply
to Models listed
in 1) above
Code Description
Model (C)(H)(HC)RG/RP(B) Sizes
Qty per
furnace
section
75/100 125 150/175 200/225 250/300 350 400
Model RPBL, RGBL, PGBL Sizes 500/600 700/1050 400/800/1200
Model RPDBL Sizes 1000/1200 1400 800 / 1600
Model HRPD Sizes 250 300/350 400 500/600 700 800
170
Heat
Exchanger
Aluminized Steel 1 44301 44304 44307 44310 44313 44316 44319
409 Stainless Steel 1 44302 44305 44308 44311 44314 44317 44320
321 Stainless Steel 1 44303 44306 44309 44312 44315 44318 44321
171A Burner Rack Slide Rail 2 9897 9857 9819 9781 9745 9709 9517
171A Burner Rack Back Brace 1 9525
172 Gasket for Fan Control, Limit Control, Patch Plate 2 17083
173 Patch Plate (not illustrated) 1 9814
174 Support Bracket RG,CRG,RP,CRP & "B" Models
>
55101
(2) (2) (2) (2) (4) (4) (4)
175 Finger Bafe RG,CRG,RP,CRP & "B" Models
>
45399
(3) (4) (6) (8) (11) (13) (15)
176 Btm Bafe Spprt RG,CRG,RP,CRP & "B" Models 1 46478 46484 46489 46494 46499 46504 46509
177 Rear Top Bafe Support 1 55103 55104 55106 55108 55110 55112 55114
178 Rear Top Bafe 1 55116 55117 55119 55121 55123 55125 55127
179
Side Finger Bafe RG, CRG, RP, CRP & "B"
Models
2 55128
180
Heat
Exchanger
Tube Bafes
Series 8 - All Models;
Prior to Series 8 - "C" Models Only
>
85727 ("V" Bafe)
(4) (5) (7) (9) (12) (14) (16)
181 High CFM Conversion Kit (RP duct furnace only) 1 263308 (to convert Model RP to allow for higher CFM)
Codes 183/184 - Burner Rack, All Models
Burner Rack and Components - all Models as listed in the Table (one per furnace section)
188
183/184
187
186
202 - Site
Glass
189
203A-D Air Shutters
191/192
Carryover
Tube
and Drip
Shield
190
189
Code 194 - Burner Orices
Code 193 -
Manifold
Main Burner Orice - Drill Size to P/N
Size 41 42 43 44 45 55 1.20mm 1.45mm 1.50mm
P/N 11792 84437 11828 11833 38678 11830 63003 61652 93410
Carryover Orice - Drill Size to P/N
Size 70 65 59 57 56 54
P/N 9870 9680 10370 38274 9791 9792
171A
180
171B
172