AdonisC2_AEcopy110F_FM.book Page 1 Wednesday, October 3, 2001 1:43 PM 1035/1045 Operating Instructions Copy Reference Zdsh000j.eps Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual.
AdonisC2_AEcopy110F_FM.book Page 1 Wednesday, October 3, 2001 1:43 PM RICOH COMPANY, LTD. 15-5, Minami Aoyama 1-chome, Minato-ku, Tokyo 107-8544, Japan Phone: +81-(0)3-3479-3111 Spain RICOH ESPAÑA S.A. Avda. Litoral Mar, 12-14, 08005 Barcelona Phone: +34-(0)93-295-7600 The Netherlands RICOH EUROPE B.V. Groenelaan 3, 1186 AA, Amstelveen Phone: +31-(0)20-5474111 Italy RICOH ITALIA SpA Via della Metallurgia 12, 37139 Verona Phone: +39-045-8181500 United Kingdom RICOH UK LTD.
AdonisC2_AEcopy110F_FM.book Page 1 Wednesday, October 3, 2001 1:43 PM Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the Safety Information before using this machine.
AdonisC2_AEcopy110F_FM.book Page 1 Wednesday, October 3, 2001 1:43 PM In accordance with IEC 60417, this machine uses the following symbols for the main power switch: a means POWER ON. c means STAND BY. Copyright © 2001 Ricoh Co., Ltd.
AdonisC2_AEcopy110F_FM.book Page i Wednesday, October 3, 2001 1:43 PM Safety Information When using your equipment, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
AdonisC2_AEcopy110F_FM.book Page ii Wednesday, October 3, 2001 1:43 PM R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
AdonisC2_AEcopy110F_FM.book Page iii Wednesday, October 3, 2001 1:43 PM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section.
AdonisC2_AEcopy110F_FM.book Page iv Wednesday, October 3, 2001 1:43 PM TABLE OF CONTENTS Machine Types........................................................................................... 1 What You Can Do with This Machine (Copy Mode)................................ 2 Guide To Components .............................................................................. 5 Output Tray Guide......................................................................................... 7 Options .................
AdonisC2_AEcopy110F_FM.book Page v Wednesday, October 3, 2001 1:43 PM 2. Copying Basic Procedure ...................................................................................... Setting Originals...................................................................................... Setting Originals on the Exposure Glass .................................................... Setting Originals in the Document Feeder .................................................. Original Orientation .................
AdonisC2_AEcopy110F_FM.book Page vi Wednesday, October 3, 2001 1:43 PM Duplex....................................................................................................... 82 1 Sided → 2 Sided ...................................................................................... 82 2 Sided → 2 Sided ...................................................................................... 83 Combine ...................................................................................................
AdonisC2_AEcopy110F_FM.book Page vii Wednesday, October 3, 2001 1:43 PM 3. Document Server Overview................................................................................................. Process ..................................................................................................... Features and Benefits ........................................................................... On Demand Printing..................................................................................
AdonisC2_AEcopy110F_FM.book Page viii Wednesday, October 3, 2001 1:43 PM d Adding Staples ................................................................................. 1000-Sheet Finisher.................................................................................. 2 Tray Finisher .......................................................................................... e Removing Jammed Staples............................................................. 1000-Sheet Finisher........................
AdonisC2_AEcopy110F_FM.book Page ix Wednesday, October 3, 2001 1:43 PM 6. REMARKS Do's And Don'ts..................................................................................... Where to Put Your Machine.................................................................. Machine Environment ............................................................................... Moving....................................................................................................... Power Connection..........
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 1 Wednesday, October 3, 2001 1:43 PM Machine Types This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 3 Wednesday, October 3, 2001 1:43 PM *1 Optional 2 Tray finisher is reguired. *2 Optional Bridge unit and optional finisher are reguired.
AdonisC2_AEcopy110F_FM.book Page 4 Wednesday, October 3, 2001 1:43 PM 1. “Selecting Original Type Setting” ⇒ P.36 23. “2 Sided 8 Pages → Combine 2 Side” ⇒ P.96 2. “Adjusting Copy Image Density” ⇒ P.35 24. “2 Sided 16 Pages → Combine 2 Side” ⇒ P.97 3. “Setting Special Originals” ⇒ P.31 4. “Image Repeat” ⇒ P.109 5. “Double Copies” ⇒ P.110 6. “Centering” ⇒ P.111 7. “Erase” ⇒ P.113 8. “Margin Adjustment” ⇒ P.118 9. “Positive/Negative” ⇒ P.112 10. “Stamp” ⇒ P.120 11. “1 Sided → 2 Sided” ⇒ P.82 12.
AdonisC2_AEcopy110F_FM.book Page 5 Wednesday, October 3, 2001 1:43 PM Guide To Components 1. Document Feeder (ADF) 7. Operation switch The document feeder automatically feeds a stack of originals one by one. Press this switch to turn the power on (the On indicator light up). To turn the power off, press this switch again (the On indicator goes off). 2. Exposure glass Place originals here face down for copying. ⇒ P.18 “Originals” 8. Control panel 3. Internal tray 9.
AdonisC2_AEcopy110F_FM.book Page 6 Wednesday, October 3, 2001 1:43 PM 1. Bypass tray 2. Right side cover Use when copying onto OHP transparencies, adhesive labels, translucent paper, postcards, and custom size paper. Open this when a paper jam occurs. 1. Ventilation hole Prevents overheating. Do not obstruct the ventilation hole by placing an object near it or leaning an object against it. If the machine overheats, a fault might occur.
AdonisC2_AEcopy110F_FM.book Page 7 Wednesday, October 3, 2001 1:43 PM Output Tray Guide When copying onto OHP transparencies and translucent paper, raise the guide. This prevents copies from being curled when delivered. ❖ To copy onto normal paper and thick paper Slide the guide in the direction of the arrow. ❖ To copy onto OHP transparencies and translucent paper Insert your forefinger into the indent on the guide and slide the guide to the right. ❖ To copy onto A3, 11” × 17” paper Raise the end fence.
AdonisC2_AEcopy110F_FM.book Page 8 Wednesday, October 3, 2001 1:43 PM Options 1. 1000-Sheet Finisher 6. Large Capacity Tray (LCT) Sorts, stacks, and staples copies. Holds 1,500 sheets of paper. 2. External tray 7. Paper tray unit If you selected this as the output tray, copied paper is delivered here face down. Consists of two paper trays. 3. Platen cover Relays copies to the external tray or finisher. Lower this cover over originals for copying. 9. 2 Tray Finisher 4.
AdonisC2_AEcopy110F_FM.book Page 9 Wednesday, October 3, 2001 1:43 PM Control Panel 1. Screen Contrast knob 8. {Energy Saver}} key Adjusts the brightness of the display panel. Press to switch to and from Energy Saver mode. ⇒ P.66 “Energy Saver Mode”. 2. Indicators 9. {Interrupt}} key These indicators show errors or the status of the machine. ⇒ P.165 “Troubleshooting”. Press to make interrupt a long copy job to make copies. ⇒ P.66 “Interrupt Copy”. 3.
AdonisC2_AEcopy110F_FM.book Page 10 Wednesday, October 3, 2001 1:43 PM 14. {Clear/Stop}} key • Clear Press to delete a number entered. • Stop Press to stop a copy job in progress. 15. {#}} key Press to enter a value. 16. Number keys Use to enter the desired number of copies and data for selected modes. 17. Function keys Press the appropriate key to choose any of the following functions: • • • • • Copy Document Server Facsimile Printer Scanner 18.
AdonisC2_AEcopy110F_FM.book Page 11 Wednesday, October 3, 2001 1:43 PM Display Panel The display panel shows the status of the machine, error messages and function menus. Important ❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to the display panel. If you do, the display might be damaged. Note ❒ The function items displayed serve as selector keys. You can select or specify an item by lightly pressing it.
AdonisC2_AEcopy110F_FM.book Page 12 Wednesday, October 3, 2001 1:43 PM 7. Shows the available functions. Press a function name to display its menu. For example, press the [Reduce/Enlarge] key to bring up the Reduce/Enlarge menu. 8. A clip mark appears for a currently selected function. ❖ Function menu 1. Items you can select. 2. The key highlighted with the lower line underlined indicates the tray feeding the paper. ❖ Document Server initial display 1. Operational status and messages. 2.
AdonisC2_AEcopy110F_FM.book Page 13 Wednesday, October 3, 2001 1:43 PM Function List Based on Options The functions that are available to you depend on your machine configuration and which options you have. See the table below.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 15 Wednesday, October 3, 2001 1:43 PM 1. Basics Turning On the Power To turn the machine on, press the operation switch. Note ❒ This machine automatically enters Energy Saver mode or turns itself off if you do not use the machine for a while. P.28 “Auto Off” and “Timer Setting” in the System Settings manual. Turning On the Main Power A Make sure that the power cord is firmly plugged into the wall outlet.
AdonisC2_AEcopy110F_FM.book Page 16 Wednesday, October 3, 2001 1:43 PM Basics Turning On the Power A Press the operation switch to make the On indicator goes on. The display panel will come on. 1 Note ❒ Even if you press the operation switch, the indicator do not goes off and blink in the following cases: • When the platen cover or the document feeder is open. • When communication is in progress with external equipment. • When the hard disk is operating.
AdonisC2_AEcopy110F_FM.book Page 17 Wednesday, October 3, 2001 1:43 PM Changing Modes Changing Modes You can use this machine not only as a copier, but also as a fax, printer, document server and scanner as well. Press the {Copy}, {Facsimile}, {Printer}, {Scanner} or {Document Server} key to use that function.
AdonisC2_AEcopy110F_FM.book Page 18 Wednesday, October 3, 2001 1:43 PM Basics Originals Sizes and Weights of Recommended Originals 1 ❖ Metric version Where Original Is Set Original Size Original Weight Exposure glass Up to A3 -- Document feeder 1-sided originals: 40 – 128g/m2 A3L – B6KL 2-sided originals: 52 – 105g/m2 A3L – A5KL ❖ Inch version Where Original Is Set Original Size Original Weight Exposure glass Up to 11" × 17" -- Document feeder 1-sided originals: 11 – 34 lb.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 20 Wednesday, October 3, 2001 1:43 PM Basics Missing Image Area ❖ Exposure glass 1 Reference position A3 Horizontal size Vertical size Maximum Scanning area A3 (297x420mm) 11"x17" (279x432mm) A4 A3 CP01AEE ❖ Document feeder Limitation ❒ Even if you correctly set originals in the document feeder or on the exposure glass, 3mm (0.1") margins on all four sides of the original might not be copied.
AdonisC2_AEcopy110F_FM.book Page 21 Wednesday, October 3, 2001 1:43 PM Copy Paper Copy Paper Recommended Paper Sizes and Types 1 The following limitations apply to each tray: Tray 1 *4 Tray 2 *4 Metric Version Inch Version A3L, B4L, A4KL, B5KL, , <11" × 17"L>, <81/2" × 14"L>, <81/2" × 11"KL>, <8" × 13"L>, <81/2" × 13"L>, <81/4" × 13"L>, <81/4" × 14"L>, <11" × 14"L>, <71/4" × 101/2"L>, <8" × 101/2"KL>, <51/2" × 81/2"L> 64-105g/m2 500 sheet , (17-28lb.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 23 Wednesday, October 3, 2001 1:43 PM Copy Paper Important ❒ If you use damp or curled paper, a misfeed might occur. In this case, try turning over the paper stack in the paper tray. If there is no improvement, change to paper with less curl. 1 Note ❒ When you use the bypass tray, it is recommended to set the copy paper direction to L. ❒ Postcards should be fed from the bypass tray.
AdonisC2_AEcopy110F_FM.book Page 24 Wednesday, October 3, 2001 1:43 PM Basics Direction-fixed paper or 2-sided paper The direction-fixed (top to bottom) or 2-sided paper (letterhead paper, punched paper, or copied paper, e.g.) might not be printed correctly depending on how the originals and paper are set in place. Set "Letterhead setting" of system settings and then set the original and paper as shown below. ⇒ “Letterhead Setting” in ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 25 Wednesday, October 3, 2001 1:43 PM Copy Paper Non-recommended Paper R CAUTION: • Do not use aluminum foil, carbon paper, or similar conductive paper to avoid a fire or equipment failure. 1 Important ❒ Do not use any of the following kinds of paper or a fault might occur.
AdonisC2_AEcopy110F_FM.book Page 26 Wednesday, October 3, 2001 1:43 PM Basics Toner Handling Toner 1 R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
AdonisC2_AEcopy110F_FM.book Page 27 Wednesday, October 3, 2001 1:43 PM 2. Copying Basic Procedure A Make sure that the machine is in Copy mode. If the machine is not in Copy mode, press the {Copy} key. B When the machine is set for the user code, enter the user code with the number keys and then press the {#} } key. Reference ⇒ P.66 “Other Functions”. C Make sure that there are no previous settings remaining. Note ❒ To clear settings, press the {Clear Modes} key. D Set your originals. Reference ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 28 Wednesday, October 3, 2001 1:43 PM Copying - System Reset The machine returns to its initial condition automatically when your job is finished, after a certain period of time. This function is called “System Reset”. 2 Note ❒ You can change the System Reset time. ⇒ “System Reset Timer” in “System Settings manual”. - Auto Off The machine turns itself off automatically after your job is finished, after a certain period of time. This function is called “Auto Off”.
AdonisC2_AEcopy110F_FM.book Page 29 Wednesday, October 3, 2001 1:43 PM Setting Originals Setting Originals Limitation ❒ Set originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied. Note ❒ Basically originals should be aligned to the rear left corner. However, some copy functions may produce different results depending on the direction of the originals. For details, see the explanations of each function.
AdonisC2_AEcopy110F_FM.book Page 30 Wednesday, October 3, 2001 1:43 PM Copying Setting Originals in the Document Feeder Note ❒ The last page should be on the bottom. ❒ Do not stack originals beyond the limit mark on the side fence of the document feeder. ❒ The original might become dirty if it is written with a pencil or similar tools. 2 Reference Regarding originals that the document feeder can handle. ⇒ P.18 “Originals”.
AdonisC2_AEcopy110F_FM.book Page 31 Wednesday, October 3, 2001 1:43 PM Setting Originals 90° Turn Setting Special Originals When you want to copy A3K, B4K or 11" × 17"K size originals, set your original in the landscape orientation and then press the key. The machine rotates the original image and you can make copies as you wish. This is useful for copying large originals with the Staple, Punch, Duplex, Combine or Stamp functions.
AdonisC2_AEcopy110F_FM.book Page 32 Wednesday, October 3, 2001 1:43 PM Copying C Press the [OK] key. Mixed Size mode When originals of different sizes are set on the document feeder at a time, the machine automatically checks the size of the originals and makes copies. 2 D Set your originals, then press the {Start} } key. E After all the previously set origi- nals are fed, set the next originals. The second and subsequent originals can be fed automatically without pressing the {Start} key.
AdonisC2_AEcopy110F_FM.book Page 33 Wednesday, October 3, 2001 1:43 PM Setting Originals A Press the [Special Original] key. Setting Custom Size Originals When setting custom size originals in the document feeder, specify the size of the originals. Limitation ❒ The paper size that can be set with this function is vertical 128-297mm (5" – 11"), horizontal 128-1,260mm (5" – 49"). B Press the [Mixed size] key. 2 A Press the [Special Original] key. C Press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 34 Wednesday, October 3, 2001 1:43 PM Copying D Enter the vertical size of the original with the Number keys, then press the [#] key. 2 E Press the [OK] key. F Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 35 Wednesday, October 3, 2001 1:43 PM Basic Functions Basic Functions The following basic functions are explained in this section. ❖ Adjusting Copy Image Density Auto and Manual Image Density ❖ Selecting Original Type Setting Text, Text·Photo, Photo, Pale, Generation Copy ❖ Selecting Copy Paper Auto Paper Select and Manual Paper Select ❖ Auto Reduce/Enlarge The machine can choose an appropriate reproduction ratio based on the paper and original sizes you select.
AdonisC2_AEcopy110F_FM.book Page 36 Wednesday, October 3, 2001 1:43 PM Copying Auto Image Density A Make sure that the [Auto Image Density] key is selected. Combined Auto and Manual Image Density A Make sure that the [Auto Image Density] key is selected. B Press the [Lighter] or [Darker] key to 2 adjust the density. Note ❒ If the [Auto Image Density] key is not selected, press the [Auto Image Density] key. ❒ If you do not wish to set any other functions, press the {Start} key to start copying.
AdonisC2_AEcopy110F_FM.book Page 37 Wednesday, October 3, 2001 1:43 PM Basic Functions ❖ Pale Select this mode for originals that have lighter lines written in pencil, or for faint copied slips. The faint lines will be clearly copied. ❖ Generation Copy If your originals are copies (generation copies), the copy image can be reproduced sharply and clearly.
AdonisC2_AEcopy110F_FM.book Page 38 Wednesday, October 3, 2001 1:43 PM Copying Selecting Copy Paper There are two ways to select copy paper: ❖ Auto Paper Select The machine selects a suitable size of copy paper automatically based on the original size and the reproduction ratio. ⇒ P.40 “Rotated copy”. 2 ❖ Manual Paper Select Choose the tray containing the paper you wish to copy onto: Paper Tray, Bypass Tray or large capacity tray (LCT). Reference ⇒ P.58 “Copying from the Bypass Tray”.
AdonisC2_AEcopy110F_FM.book Page 39 Wednesday, October 3, 2001 1:43 PM Basic Functions Auto Paper Select A Make sure that the [Auto Paper Select] key is selected. 2 Note ❒ If the [Auto Paper Select] key is not selected, press the [Auto Paper Select] key. ❒ If you do not wish to set any other functions, press the {Start} key to start copying. ❒ If “Yes” has been selected in “Original Mode Display” of the User Tools, press the [Auto Paper Select] key.
AdonisC2_AEcopy110F_FM.book Page 40 Wednesday, October 3, 2001 1:43 PM Copying - Rotated copy If the direction in which your original is set (landscape or portrait) is different from that of the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ⇒ “Auto Paper Select” in P.38 “Selecting Copy Paper” and ⇒ P.41 “Auto Reduce/Enlarge”.
AdonisC2_AEcopy110F_FM.book Page 41 Wednesday, October 3, 2001 1:43 PM Basic Functions Auto Reduce/Enlarge The machine can choose an appropriate reproduction ratio based on the paper and original sizes you select. ❖ Inch version Where Original Is Set Original Size and Direction Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL Document feeder *1 A4KL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL *1 Limitation ❒ You cannot use the bypass tray with this function.
AdonisC2_AEcopy110F_FM.book Page 42 Wednesday, October 3, 2001 1:43 PM Copying Sort/Stack/Staple The machine can scan your originals into memory and automatically sort the copies.
AdonisC2_AEcopy110F_FM.book Page 43 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple ❖ Inch version Inter• 81/2" × 14"L or larger: 250 nal tray sheets (20 lb.) • 81/2" × 11K or smaller: 500 sheets (20 lb.) Internal tray 2 (1 bin tray) 125 sheets (20 lb.) Sort Copies can be assembled as sets in sequential order. ❖ Sort Copies can be assembled as sets in sequential order. 2 Extar125 sheets (20 lb.) nal tray 1000Sheet Finisher 2 Tray Finisher • 81/2" × 14"L or larger: 500 sheets (20 lb.
AdonisC2_AEcopy110F_FM.book Page 44 Wednesday, October 3, 2001 1:43 PM Copying ❒ The paper sizes that can be used in the Rotate Sort function are as follows: Metric version A4KL, B5KL Inch version 81/2" × 11"KL ❒ To use the Rotate Sort function, two paper trays identical in size and different in direction (KL) are required. 2 Reference For the paper capacity of the optional finishers, ⇒ P.238 “1000Sheet Finisher (Option)”, ⇒ P.239 “2 Tray Finisher (Option)”.
AdonisC2_AEcopy110F_FM.book Page 45 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple ❖ When the 2 Tray Finisher is installed When setting an original on the exposure glass or in the document feeder using Batch mode Reference ⇒ P.31 “Batch mode”. 2 A Set the original, then press the {Start} } key. Note ❒ When the optional finisher is installed, use the User Tools to display [Rotate Sort]. ⇒ “Select Stack Function” in P.226 “Input/ Output”. B Enter the number of copy sets with the number keys.
AdonisC2_AEcopy110F_FM.book Page 46 Wednesday, October 3, 2001 1:43 PM Copying Note ❒ The paper sizes that can be used in the Stack function are as follows: 2 C Set your originals, then press the {Start} } key. 1000-Sheet Finisher 2 Tray Finisher When setting a stack of originals in the document feeder Metric version A3L, B4L, A4KL, B5KL, A5KL A3L, B4L, A4KL, B5KL, A5KL A Set a stack of originals in the document feeder, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 47 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple Staple The optional finisher and the bridge unit are required to use this function. Each copy set can be stapled together. 2 Limitation ❒ You cannot use the following paper in this function: • Postcards • Translucent paper • OHP transparencies • Adhesive labels • Curled paper • Low stiffness paper • Paper of different vertical sizes Note ❒ For this mode, the following limitation applies.
AdonisC2_AEcopy110F_FM.book Page 48 Wednesday, October 3, 2001 1:43 PM Copying ❖ Inch version With 1000-Sheet Finisher With 2 Tray Finisher Paper size 11" × 17"L, 8 /2" × 14"L, 81/2" × 11"KL 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL Stapler capacity • 81/2" × 11" or smaller: 30 sheets (20 lb.) • 81/2" × 11" or smaller: 50 sheets (20 lb.) • 81/2" × 14" or larger: 20 sheets (20 lb.) • 81/2" × 14" or larger: 30 sheets (20 lb.) 2 1 • Mixed Size: 30 sheets (20lb.
AdonisC2_AEcopy110F_FM.book Page 49 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple ❖ 1000-sheet Finisher When your machine is equipped with the 1000-sheet finisher, the stapling position will be fixed to “Top Slant”. Original setting Exposure glass Stapling position Document Feeder 2 Top Slant K STAPLEBE L Note ❒ Original images are not rotated.
AdonisC2_AEcopy110F_FM.book Page 50 Wednesday, October 3, 2001 1:43 PM Copying Original setting Exposure glass Stapling position Document Feeder 2 STAPLEDE Left 2 K *1 L STAPLE31 K STAPLE33 STAPLE32 *1 Top 2 STAPLEEE *1 L Available staple positions except A3, B4, size of paper. Note ❒ You cannot change stapling positions during copying. ❒ When the original image is rotated, the stapling direction turns by 90°. ❒ By setting orientation of papers and originals, “Blank part will appear.
AdonisC2_AEcopy110F_FM.book Page 51 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple A Select one of the stapling positions. ❖ 1000-Sheet Finisher 2 ❖ 2 Tray Finisher Note ❒ When you select the stapling position, Sort mode is automatically selected. Reference ⇒ P.48 “Stapling position and original setting” B Enter the number of copy sets with the number keys. Note ❒ To change the entered number, press the {Clear/Stop} key. C Set your originals, then press the {Start}} key.
AdonisC2_AEcopy110F_FM.book Page 52 Wednesday, October 3, 2001 1:43 PM Copying When setting an original on the exposure glass or in the document feeder using Batch mode Reference ⇒ P.31 “Batch mode”. A Set the original, then press the {Start} } key. 2 Note ❒ Start with the first page to be copied. B Set the next original. When it is placed on the exposure glass, press the {Start} } key. Note ❒ Set the original in the same direction as the first one.
AdonisC2_AEcopy110F_FM.book Page 53 Wednesday, October 3, 2001 1:43 PM Sort/Stack/Staple A Press the {Start}} key. The scanned pages are delivered to the tray. Then, the image data in memory is cleared. B Remove the copies and continue copying by following the instructions on the display. 2 To Remove the Paper from the Staple Unit If you cancel the stapling copy job in the middle of the job, the paper might be left in the staple unit. In this case, remove the paper from the staple unit.
AdonisC2_AEcopy110F_FM.book Page 54 Wednesday, October 3, 2001 1:43 PM Copying Punch The optional 2 tray finisher and the bridge unit are required to use this function. This function is used to make punch holes in copies.
AdonisC2_AEcopy110F_FM.book Page 55 Wednesday, October 3, 2001 1:43 PM Punch Note ❒ When using Punch and Combine, Double Copies, or Auto Reduce/Enlarge, the message "Blank part will appear. Check orientation." may appear because of the orientation of the original and the copy paper. If this occurs, change the orientation of the copy paper.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 57 Wednesday, October 3, 2001 1:43 PM Punch Reference If the punch waste box fills up, ⇒ P.200 “y Removing Punch Waste”. A Select the Punch position. 2 Note ❒ When stapling copies, also select a stapling position. ⇒ P.47 “Staple”. B Enter the number of copy sets with the number keys. Note ❒ To change the entered number, press the {Clear/Stop} key. ❒ If you wish to use the Sort function, press the [Sort] key. C Set your originals, then press the {Start}} key.
AdonisC2_AEcopy110F_FM.book Page 58 Wednesday, October 3, 2001 1:43 PM Copying Copying from the Bypass Tray Use the bypass tray to copy onto OHP transparencies, adhesive labels, translucent paper, postcards, and copy paper that cannot be set in the paper tray. 2 A Open the bypass tray.
AdonisC2_AEcopy110F_FM.book Page 59 Wednesday, October 3, 2001 1:43 PM Copying from the Bypass Tray Note ❒ The face side of the paper set is copied on. ❒ Do not stack paper over the limit mark, otherwise a skew image or paper misfeeds might occur. ❒ If the beeper is turned off, lightly insert the copy paper until it stops. Refer to the System Settings manual. ❒ When the document feeder is open, set the direction of the copy paper to L.
AdonisC2_AEcopy110F_FM.book Page 60 Wednesday, October 3, 2001 1:43 PM Copying B Press the [Custom Size] key. 2 C Press the [Vertical mm] key and enter the vertical size of the paper with the number keys, then press the [#] key. E To register the custom size entered, press the [Store] key and then press the [Cancel] key. Note ❒ If you do not register the custom size, go to step F. ❒ Only one custom size can be stored. ❒ To recall the custom size stored, press the [Recall] key.
AdonisC2_AEcopy110F_FM.book Page 61 Wednesday, October 3, 2001 1:43 PM Copying from the Bypass Tray B Lightly insert the OHP transparencies or thick paper face down until the beeper sounds. The k indicator on the display automatically goes on. Important ❒ When you set an OHP transparency, make sure that its front and back faces are properly positioned. ❒ To avoid paper misfeeds, fan the paper before setting it in the tray. 2 C Press the {#}} key. D Select [OHP Sheet] or [Thick Paper].
AdonisC2_AEcopy110F_FM.book Page 62 Wednesday, October 3, 2001 1:43 PM Copying Programs You can store frequently used copy job settings in machine memory, and recall them for future use. ❖ Storing Your Settings You can store your settings you frequently use. 2 ❖ Deleting A Program You can delete a stored program. Storing a Program A Edit the copy settings so that all functions you want to store in this program are selected. B Press the {Program}} key.
AdonisC2_AEcopy110F_FM.book Page 63 Wednesday, October 3, 2001 1:43 PM Programs Note ❒ If you do not wish to enter the program name, go to step F. ❒ You can register up to 40 characters. ❒ To change the name entered, press the [Backspace], [Delete] or {Clear/Stop} key and enter new letters. Reference For details on entering characters, ⇒ "Entering Text Characters" in the System Settings manual. F Press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 64 Wednesday, October 3, 2001 1:43 PM Copying Note ❒ To cancel the deletion, press the [No] key. Recalling a Program A Press the {Program}} key. 2 B Press the [Recall] key. C Press the program number you want to recall. The stored settings are displayed. Note ❒ Only programs with m contain a program. D Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 65 Wednesday, October 3, 2001 1:43 PM Job Preset Job Preset If a long copy job is in progress and you do not wish to wait for it to finish, you can use this function to set up the next one copy job in advance. When the current copy job is finished, your copy job will be started automatically. A Press the {Copy}} key. D Press the [To "Printing"] key. After the current copy job, the next job starts automatically.
AdonisC2_AEcopy110F_FM.book Page 66 Wednesday, October 3, 2001 1:43 PM Copying Other Functions Energy Saver Mode If you do not operate the machine for a certain period after copying, or when you press the {Energy Saver} key, the display disappears and the machine enters Energy Saver mode. When you press the {Energy Saver} key again, the machine returns to the ready condition. In Energy Saver mode, the machine uses less electricity.
AdonisC2_AEcopy110F_FM.book Page 67 Wednesday, October 3, 2001 1:43 PM Other Functions D When copying is complete, remove your originals and copies. E Press the {Interrupt}} key again. The Interrupt indicator goes off. The previous copy job settings will be restored and the machine will continue copying from where it left off. Original Beeper The beeper sounds and an error message is displayed when you leave your originals on the exposure glass after copying.
AdonisC2_AEcopy110F_FM.book Page 68 Wednesday, October 3, 2001 1:43 PM Copying B Press the [Change Quantity] key. 2 C Enter the number of copy sets with the number keys, then press the {#} } key. Note ❒ The number of sets you can enter differs depending on the timing of pressing the {Clear/ Stop} key. ❒ To change the entered number, press the {Clear/Stop} key. D Press the [Continue] key.
AdonisC2_AEcopy110F_FM.book Page 69 Wednesday, October 3, 2001 1:43 PM Preset Reduce/Enlarge Preset Reduce/Enlarge You can select a preset ratio for copying. ❖ Metric version Ratio (%) Note ❒ You can select one of 12 preset ratios (5 enlargement ratios, 7 reduction ratios). ❒ Use “Create Margin” to reduce the image to 93% of its original size with the centre as reference. You can register this function in a shortcut key on the initial display.
AdonisC2_AEcopy110F_FM.book Page 70 Wednesday, October 3, 2001 1:43 PM Copying 2 Ratio (%) Original → Copy paper size 78 8 /2" × 14"→8 /2" × 11" 73 11" × 15"→81/2" × 11" 65 11" × 17"→81/2" × 11" 1 50 (reduce area by /4) 11" × 17"→51/2" × 81/2" 25 -- 1 1 A Press the [Reduce/Enlarge] key. Create Margin mode Use “Create Margin” to reduce the image by 93% of its original size with the centre position as reference. You can register this function in a shortcut key on the initial display.
AdonisC2_AEcopy110F_FM.book Page 71 Wednesday, October 3, 2001 1:43 PM Zoom Zoom You can change the reproduction ratio in 1% steps. B Enter the ratio. To select the ratio with the [n] and [o] keys 2 A Select a preset ratio which is close to the desired ratio by using [Reduce] or [Enlarge]. Note ❒ The following ratios can be selected: • Metric version: 25 – 400% • Inch version: 25 – 400% ❒ You can select a ratio regardless of the size of an original or copy paper.
AdonisC2_AEcopy110F_FM.book Page 72 Wednesday, October 3, 2001 1:43 PM Copying B Enter the desired ratio with the number keys. Note ❒ To change the ratio entered, press the [Clear] or {Clear/ Stop} key and enter the new ratio. C Press the [#] key. D Press the [OK] key. 2 C Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 73 Wednesday, October 3, 2001 1:43 PM Size Magnification Size Magnification This function calculates an enlargement or reduction ratio based upon the lengths of the original and copy. B Press the [Specifid Ratio] key. 2 Amm amm C Make sure that the [Specifid Ratio] key is highlighted. Preparation Measure and specify the lengths of the original and copy by comparing “A” with “a.
AdonisC2_AEcopy110F_FM.book Page 74 Wednesday, October 3, 2001 1:43 PM Copying E Enter the length of the copy with the number keys and press the [#] key. Note ❒ To change the length entered, press the [Clear] or {Clear/Stop} key and enter the new length. ❒ To change the length after pressing the [#] key, select [Original] or [Copy] and enter the desired length. 2 F Press the [OK] key. G Press the [OK] key. H Set your original, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 75 Wednesday, October 3, 2001 1:43 PM Directional Magnification (%) Directional Magnification (%) Copies can be reduced or enlarged at different reproduction ratios horizontally and vertically. B Press the [Specifid Ratio] key. 2 a% b% C Press the [Direct. Mag.%] key. CP2P01EE Note ❒ The following ratios can be selected: • Metric version: 25 – 400% • Inch version: 25 – 400% ❒ You can select a ratio regardless of the size of an original or copy paper.
AdonisC2_AEcopy110F_FM.book Page 76 Wednesday, October 3, 2001 1:43 PM Copying C Press the [Vertical] key. D Enter the desired ratio with the number keys, followed by the [#] key. E Press the [OK] key. To specify a ratio with the [n] and [o] keys 2 A Press the [With no] key. B Press the [Horizontal] key. C Adjust the ratio using the [n n] or [o o] key. Note ❒ Pressing the [n] or [o] key changes the ratio in 1% steps. Pressing and holding down the [n] or [o] key changes it in 10% steps.
AdonisC2_AEcopy110F_FM.book Page 77 Wednesday, October 3, 2001 1:43 PM Directional Size Magnification (mm) Directional Size Magnification (mm) The suitable reproduction ratios will be automatically selected when you enter the horizontal and vertical lengths of the original and copy image you require. 1 2 3 4 Note ❒ You can enter sizes within the following ranges: Metric version 1 – 999mm (in 1mm steps) Inch version 0.1" – 99.9" (in 0.
AdonisC2_AEcopy110F_FM.book Page 78 Wednesday, October 3, 2001 1:43 PM Copying C Press the [Dir.Size Mag mm] key. 2 D Enter the horizontal size of the original with the number keys, then press the [#] key. Note ❒ To change the value entered, press the [Clear] or {Clear/Stop} key and enter the new value. E Enter the horizontal size of the copy with the number keys, then press the [#] key. F Enter the vertical size of the original with the number keys, then press the [#] key.
AdonisC2_AEcopy110F_FM.book Page 79 Wednesday, October 3, 2001 1:43 PM Duplex/Combine/Series Duplex/Combine/Series You can make copies in a variety of formats by combining the following modes: • 1 Sided/2 Sided originals • 1 Sided/2 Sided copies • Duplex • Combine • Book • Series B Select [1 Sided] or [2 Sided] for copying. 1 2 2 A Press [Dup./Combine/Series] and check your originals. And select [1 Sided] or [2 Sided] for the originals.
AdonisC2_AEcopy110F_FM.book Page 80 Wednesday, October 3, 2001 1:43 PM Copying Original Direction and Completed Copies Originals and Copy Direction The resulting copy image will differ according to the direction in which you set your original (lengthwise K or widthwise L). 2 You can select the orientation ([Top to Top], [Top to Bottom]). ⇒ P.80 “Specifying Orientation of Bound Originals”.
AdonisC2_AEcopy110F_FM.book Page 81 Wednesday, October 3, 2001 1:43 PM Duplex/Combine/Series B Press the [Orientation] key. 2 C Select an original orientation and a copy orientation. D Press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 82 Wednesday, October 3, 2001 1:43 PM Copying Duplex This function can be used in two ways: 1 Sided → 2 Sided ❖ 1 Sided → 2 Sided This mode makes two-sided copies from one-sided originals. 2 ❖ 2 Sided → 2 Sided This mode makes two-sided copies from two-sided originals. Limitation ❒ You cannot use the following copy paper in this function: • Paper smaller than A5K, 51/2" × 81/2"K (possible on A5L, 51/ 1 2" × 8 /2"L) • Paper thicker than 105g/m2, 28 lb.
AdonisC2_AEcopy110F_FM.book Page 83 Wednesday, October 3, 2001 1:43 PM Duplex B Press the [1 Sided] key for original, then press the [2 Sided] key for copy. 2 Sided → 2 Sided 1 2 Note ❒ To change the copy orientation to “Top to Bottom”, press the [Orientation] key and select [Top to Bottom]. ⇒ P.80 “Specifying Orientation of Bound Originals”. 2 1 2 A Press the [Dup./Combine/Series] key. C Press the [OK] key. D Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 84 Wednesday, October 3, 2001 1:43 PM Copying When setting an original on the exposure glass or in the document feeder using Batch mode Reference ⇒ P.31 “Batch mode”. 2 A Set the original, then press the {Start} } key. Note ❒ Start with the first page to be copied. B Set the next original. When it is placed on the exposure glass, press the {Start} } key. C Press the {#} } key after the last original has been scanned.
AdonisC2_AEcopy110F_FM.book Page 85 Wednesday, October 3, 2001 1:43 PM Combine Combine You can combine two or more originals into one copy. 1 Sided Combine mode is for 1-sided copies, and 2 Sided Combine mode for 2-sided copies. This function can be used in twelve ways: ❖ 1 Sided 2 Pages → Combine 1 Side Copies two 1-sided originals to one side of a sheet. ❖ 1 Sided 4 Pages → Combine 1 Side Copies four 1-sided originals together to one side of a sheet.
AdonisC2_AEcopy110F_FM.book Page 86 Wednesday, October 3, 2001 1:43 PM Copying ❒ When making copies in Combine mode, the border of each original can be automatically erased by 3mm, 0.1". ⇒ “Erase Original Shadow in Combine” in P.216 “Edit 1/2”. ❒ If the number of originals placed is less than the number specified for combining, the last page is copied blank as shown in the illustration. 2 1 Sided 2 Pages → Combine 1 Side Copies two 1-sided originals to one side of a sheet.
AdonisC2_AEcopy110F_FM.book Page 87 Wednesday, October 3, 2001 1:43 PM Combine A Press the [Dup./Combine/Series] key. 1 Sided 4 Pages → Combine 1 Side Copies four 1-sided originals together to one side of a sheet. 2 1 2 3 B Press the [1 Sided] key for the orig- 4 1 2 3 4 inal, then press the [Combine 1 Side] key for the copy. A Press the [Dup./Combine/Series] key. C Press the [2 Originals] key, then press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 88 Wednesday, October 3, 2001 1:43 PM Copying C Press the [4 Originals] key, then press the [OK] key. A Press the [Dup./Combine/Series] key. 2 B Press the [1 Sided] key for the orig- D Select the paper. inal, then press the [Combine 1 Side] key for the copy. E Set your originals, then press the {Start} } key. C Press the [8 Originals] key, then press the [OK] key. 1 Sided 8 Pages → Combine 1 Side Copies eight 1-sided originals together to one side of a sheet.
AdonisC2_AEcopy110F_FM.book Page 89 Wednesday, October 3, 2001 1:43 PM Combine 1 Sided 4 Pages → Combine 2 Side C Press the [4 Originals] key, then press the [OK] key. Copies four 1-sided originals to the two-page spread on both sides of a sheet. 2 1 2 1 2 3 4 4 3 D Check the orientation. A Press the [Dup./Combine/Series] key. B Press the [1 Sided] key for the original, then press the [Combine 2 Side] key for the copy.
AdonisC2_AEcopy110F_FM.book Page 90 Wednesday, October 3, 2001 1:43 PM Copying 1 Sided 8 Pages → Combine 2 Side C Press the [8 Originals] key, then press the [OK] key. Copies eight 1-sided originals together to both sides of a sheet. 2 1 2 7 1 2 5 6 3 4 7 8 1 2 D Check the orientation. 8 GCSHVYAE 1. Front 2. Back A Press the [Dup./Combine/Series] key. Note ❒ To change the copy orientation to “Top to Bottom”, press the [Orientation] key and select [Top to Bottom]. ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 91 Wednesday, October 3, 2001 1:43 PM Combine 1 Sided 16 Pages → Combine 2 Side C Press the [16 Originals] key, then press the [OK] key. Copies sixteen 1-sided originals together to both sides of a sheet. 2 1 1 2 3 4 2 5 6 7 8 1 15 16 9 10 11 12 D Check the orientation. 13 14 15 16 2 GCSHVY5E 1. Front 2. Back A Press the [Dup./Combine/Series] key. Note ❒ To change the copy orientation to “Top to Bottom”, press the [Orientation] key and select [Top to Bottom].
AdonisC2_AEcopy110F_FM.book Page 92 Wednesday, October 3, 2001 1:43 PM Copying 2 Sided 2 Pages → Combine 1 Side C Press the [2 Pages] key, then press the [OK] key. Copies one 2-sided original to one side of a sheet. 2 1 1 2 2 D Check the orientation. A Press the [Dup./Combine/Series] key. B Press the [2 Sided] key for the original, then press the [Combine 1 Side] key for the copy. Note ❒ To change the copy orientation to “Top to Bottom”, press the [Orientation] key and select [Top to Bottom].
AdonisC2_AEcopy110F_FM.book Page 93 Wednesday, October 3, 2001 1:43 PM Combine 2 Sided 4 Pages → Combine 1 Side C Press the [4 Pages] key, then press the [OK] key. Copies two 2-sided originals to one side of a sheet. 2 1 3 2 4 1 2 3 4 D Check the orientation. A Press the [Dup./Combine/Series] key. B Press the [2 Sided] key for the original, then press the [Combine 1 Side] key for the copy.
AdonisC2_AEcopy110F_FM.book Page 94 Wednesday, October 3, 2001 1:43 PM Copying 2 Sided 8 Pages → Combine 1 Side C Press the [8 Pages] key, then press the [OK] key. Copies four 2-sided originals to one side of a sheet. 2 1 3 1 2 3 4 5 2 7 4 5 6 7 8 6 8 D Check the orientation. A Press the [Dup./Combine/Series] key. B Press the [2 Pages] key for the original, then press the [Combine 1 Side] key for the copy.
AdonisC2_AEcopy110F_FM.book Page 95 Wednesday, October 3, 2001 1:43 PM Combine 2 Sided 4 Pages → Combine 2 Side C Press the [4 Pages] key, then press the [OK] key. Copies two 2-sided originals together to both sides of a sheet. 2 1 3 2 4 1 2 4 3 D Check the orientation. A Press the [Dup./Combine/Series] key. B Press the [2 Sided] key for the original, then press the [Combine 2 Side] key for the copy.
AdonisC2_AEcopy110F_FM.book Page 96 Wednesday, October 3, 2001 1:43 PM Copying 2 Sided 8 Pages → Combine 2 Side C Press the [8 Pages] key, then press the [OK] key. Copies four 2-sided originals together to both sides of a sheet. 2 1 3 5 2 7 4 6 8 1 2 5 6 3 4 7 8 1 2 D Check the orientation. GCSHVY2E 1. Front 2. Back A Press the [Dup./Combine/Series] key. Note ❒ To change the copy orientation to “Top to Bottom”, press the [Orientation] key and select [Top to Bottom]. ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 97 Wednesday, October 3, 2001 1:43 PM Combine 2 Sided 16 Pages → Combine 2 Side C Press the [16 Pages] key, then press the [OK] key. Copies eight 2-sided originals together to both sides of a sheet. 1 2 1 2 3 4 3 5 6 7 8 2 4 1 13 15 14 16 9 10 11 12 D Check the orientation. 13 14 15 16 2 GCSHVY6E 1. Front 2. Back A Press the [Dup./Combine/Series] key.
AdonisC2_AEcopy110F_FM.book Page 98 Wednesday, October 3, 2001 1:43 PM Copying Series/Book Series copies are made by separately copying the front and back of a 2-sided original or the two facing pages of a spread original onto two sheets of paper. A book is made by copying two or more originals in page order. The following types of Series and Book modes can be used: 2 ❖ Series Copies • Book → 1 Sided Copies the two facing pages of a spread original to make two 1sided copies.
AdonisC2_AEcopy110F_FM.book Page 99 Wednesday, October 3, 2001 1:43 PM Series/Book A Press the [Dup./Combine/Series] key. F Make sure that the [Auto Paper Select] key is selected. Note ❒ If the [Auto Paper Select] key is not selected, press the [Auto Paper Select] key. G Set your originals, then press the 2 {Start} } key. B Press the [Series/Book] key. Book → 2 Sided Copies a two-page spread original onto both sides of a sheet.
AdonisC2_AEcopy110F_FM.book Page 100 Wednesday, October 3, 2001 1:43 PM Copying A Press the [Dup./Combine/Series] key. G Set your originals, then press the {Start} } key. Front & Back → 2 Sided Copies each two-page spread original as it is onto both sides of a sheet. 2 B Press the [Series/Book] key. Limitation ❒ You cannot use the Front & Back → 2 Sided function from the document feeder. 1 2 1 3 C Make sure that the [Series] key is selected.
AdonisC2_AEcopy110F_FM.book Page 101 Wednesday, October 3, 2001 1:43 PM Series/Book A Press the [Dup./Combine/Series] key. G Set your originals, then press the {Start} } key. Note ❒ Press the {#} key after all originals are scanned. 2 B Press the [Series/Book] key. C Make sure that the [Series] key is selected. D Press the [Front & Back → 2 Sided] key, then press the [OK] key. E Press the [OK] key. F Select the paper.
AdonisC2_AEcopy110F_FM.book Page 102 Wednesday, October 3, 2001 1:43 PM Copying ❖ Open to Right Copying Book Originals Limitation ❒ You cannot use the bypass tray with this function. 1 2 3 3 2 4 4 Note ❒ The machine sets the reproduction ratio automatically to meet the paper size and copies the originals together onto the paper. 2 ❒ The machine uses ratios in the range of 25 to 400%. ❒ If the calculated ratio is under the available minimum ratio, it will be adjusted to the minimum ratio.
AdonisC2_AEcopy110F_FM.book Page 103 Wednesday, October 3, 2001 1:43 PM Series/Book C Press the [Book] key. How to fold copies to make a booklet 1 2 3 1 2 3 1 D Press the [1 Sided → Booklet] key, then press the [OK] key. GCBOOK2E 1. Open to Left 2. Open to Right A Press the [Dup./Combine/Series] key. E Press the [OK] key. F Select the paper. G Set your originals, then press the {Start} } key. B Press the [Series/Book] key.
AdonisC2_AEcopy110F_FM.book Page 104 Wednesday, October 3, 2001 1:43 PM Copying 2 Sided → Booklet Make 2 sided originals to copies in page order for a folded booklet as shown in the following illustrations: ❖ Open to Left 2 ❒ If the calculated ratio is under the available minimum ratio, it will be adjusted to the minimum ratio. However, with some ratios, parts of the image might not be copied. ❒ If the number of originals scanned is less than a multiple of 4, the last page is copied blank.
AdonisC2_AEcopy110F_FM.book Page 105 Wednesday, October 3, 2001 1:43 PM Series/Book B Press the [Series/Book] key. 1 Sided → Magazine Copies two or more originals to make copies in page order when they are folded and stacked. ❖ Open to Left 2 1 2 C Press the [Book] key. 2 7 8 7 1 8 4 5 3 6 GCBOOK3E ❖ Open to Right 1 D Press the [2 Sided → Booklet] key, 2 then press the [OK] key. 7 7 2 8 1 5 4 6 3 8 GCBOOK4E E Press the [OK] key. F Select the paper.
AdonisC2_AEcopy110F_FM.book Page 106 Wednesday, October 3, 2001 1:43 PM Copying ❒ If the calculated ratio is under the available minimum ratio, it will be adjusted to the minimum ratio. However, with some ratios, parts of the image might not be copied. ❒ If the number of originals scanned is less than a multiple of 4, the last page is copied blank. ❒ You can have a 3mm bounding margin around all four edges of the original left blank (erased). ⇒ “Erase Original Shadow in Combine” in P.216 “Edit 1/2”.
AdonisC2_AEcopy110F_FM.book Page 107 Wednesday, October 3, 2001 1:43 PM Series/Book G Set your originals, then press the {Start} } key. Note ❒ When placing one original on the exposure glass or in the document feeder in Batch mode, press the {#} key after all originals are scanned. 2 Sided → Magazine Copies two or more originals of 2 sided to make copies in page order when they are folded and stacked.
AdonisC2_AEcopy110F_FM.book Page 108 Wednesday, October 3, 2001 1:43 PM Copying How to fold and unfold copies to make a magazine B Press the [Series/Book] key. ❖ Open to Left 2 7 5 5 3 1 1 3 C Press the [Book] key. GCBOOK5E ❖ Open to Right 5 7 3 5 1 3 1 D Press the [2 Sided → Magazine] key, then press the [OK] key. GCBOOK6E A Press the [Dup./Combine/Series] key. E Press the [OK] key. F Select the paper. G Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 109 Wednesday, October 3, 2001 1:43 PM Edit Image Edit Image Image Repeat The original image is copied repeatedly. ❒ Part of a repeated image might not be copied depending on copy paper size, copy paper direction or reproduction ratio. ❒ You can insert separation lines between repeated images. ⇒ “Repeat Separation Line” in P.218 “Edit 2/2”. 2 A Select the size of the copy paper and the reproduction ratio. B Press the [Edit/Stamp] key.
AdonisC2_AEcopy110F_FM.book Page 110 Wednesday, October 3, 2001 1:43 PM Copying F Press the [OK] key. G Set your original, then press the {Start} } key. 2 ❒ See the following table when you select original and copy paper sizes with 100% ratio: ❖ Metric version Double Copies Original Size and Direction Copy Paper Size and Direction One original image is copied twice on one copy as shown in the illustration.
AdonisC2_AEcopy110F_FM.book Page 111 Wednesday, October 3, 2001 1:43 PM Edit Image C Press the [Double Copies] key. Note ❒ The original sizes and directions for centring are listed below. ❖ Metric version Original Original size and direction placed on: D Press the [OK] key. E Press the [OK] key. F Select the paper. G Set your originals, then press the {Start} } key. Centering You can make copies by moving the image to the centre of the copy paper.
AdonisC2_AEcopy110F_FM.book Page 112 Wednesday, October 3, 2001 1:43 PM Copying D Press the [Centering] key. B Press the [Edit Image] key. E Press the [OK] key. F Press the [OK] key. G Set your originals, then press the C Press the [Positive/Negative] key. 2 {Start} } key. Positive/Negative If your original is black and white, copy images are inverted. D Press the [OK] key. E Press the [OK] key. F Select the paper. G Set your originals, then press the {Start} } key. A Press the [Edit/Stamp] key.
AdonisC2_AEcopy110F_FM.book Page 113 Wednesday, October 3, 2001 1:43 PM Erase Erase This function erases the centre and/ or all four sides of the original image. This is useful for avoiding shadows on the copy image caused by the bound originals, such as books. This function can be used in three ways: ❖ Border This mode erases the edge margin of the original image. ❖ Center This mode erases the centre margin of the original image.
AdonisC2_AEcopy110F_FM.book Page 114 Wednesday, October 3, 2001 1:43 PM Copying Border Erase C Press the [Border] key. This function erases the edge margins. You can set the same margin width for all four sides, or you can set different margin widths for each side. 2 D Set the erase border width. Selecting [Same Width] A Press the [Same Width] key. Note ❒ If you want to erase the centre margin too, use the Centre/Border function. ⇒ P.116 “Center/Border Erase”. A Press the [Edit/Stamp] key.
AdonisC2_AEcopy110F_FM.book Page 115 Wednesday, October 3, 2001 1:43 PM Erase B Press the key for the border you wish to change and set an erase border width with the [n n] and [o o] keys. B Press the [Erase] key. Note ❒ To change the value entered, press the [n] and [o] keys and enter the new value. C Press the [OK] key. E Press the [OK] key. F Set your originals, then press the 2 C Press the [Center] key. {Start} } key. Center Erase This function erases the centre margin.
AdonisC2_AEcopy110F_FM.book Page 116 Wednesday, October 3, 2001 1:43 PM Copying Center/Border Erase C Press the [Center/Border] key. This mode erases both the centre and edge margins. You can set the same margin width for all four sides and centre, or you can set different margin widths for each. 2 D Set the erase margin width. Selecting [Same Width] A Press the [Center] key, then set the erase centre width with the [n n] and [o o] keys. A Press the [Edit/Stamp] key.
AdonisC2_AEcopy110F_FM.book Page 117 Wednesday, October 3, 2001 1:43 PM Erase Selecting [Diff. Width] A Press the [Diff. Width] key. 2 B Press the key for the part you wish to change and set an erase margin width with the [n n] and [o o] keys. Note ❒ To change the value entered, press the [n] and [o] keys and enter the new value. C Press the [OK] key. E Press the [OK] key. F Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 118 Wednesday, October 3, 2001 1:43 PM Copying Margin Adjustment You can shift the image left, right, top or bottom to make a binding margin. 2 A A Limitation ❒ If you set the margin too wide, areas you do not want to delete might be erased. Note ❒ You can change the width of the binding margin as follows: Metric version 0 – 30mm (in 1mm steps) Inch version 0" – 1.2" (in 0.1" steps) ❒ The margin width default is as follows.
AdonisC2_AEcopy110F_FM.book Page 119 Wednesday, October 3, 2001 1:43 PM Margin Adjustment C Set a binding margin for a front page. Press the [← ←] and [→ →] keys when setting the left and right margins, and the [↓ ↓] and [↑ ↑] keys when setting the top and bottom margins. 2 Note ❒ To change the value entered, press the [← ←], [→ →], [↓ ↓], [↑ ↑] keys and enter the new value. D Set a binding margin for back pages.
AdonisC2_AEcopy110F_FM.book Page 120 Wednesday, October 3, 2001 1:43 PM Copying Stamp This function prints stamp on the copies. Stamp modes are as follows: ❖ Background Numbering This function prints numbers on the background of copies. 2 ❖ Preset Stamp This function prints preset messages on copies. ❖ User Stamp This function prints custom messages on copies. Note ❒ You can change the size of the numbers with the User Tools. ⇒ “Size” in P.221 “Background Numbering”.
AdonisC2_AEcopy110F_FM.book Page 121 Wednesday, October 3, 2001 1:43 PM Stamp C Press the [Background Numbering] key. Preset Stamp 32 MB of memory is required to use this funct ion (If t he mach ine is equipped with the Printer unit, 32 MB memory is not required.). 2 D Enter the number to start counting from with the number keys. Then press the [OK] key. Note ❒ The number can be set from 1 to 999. ❒ To change the entered number, press the [Clear] or {Clear/Stop} key and enter the new number.
AdonisC2_AEcopy110F_FM.book Page 122 Wednesday, October 3, 2001 1:43 PM Copying ❒ You can choose the default settings for the position, size and density of the stamp with the User Tools. ⇒ “Stamp Position”, “Stamp Format” in P.221 “Preset Stamp 1/4-4/4”. ❒ You can choose the default settings for the print page with the User Tools. ⇒ “Stamp Format” in P.221 “Preset Stamp 1/4-4/4”. ❒ You can change the stamp language with the User Tools. ⇒ “Stamp Language” in P.221 “Preset Stamp 1/4-4/4”.
AdonisC2_AEcopy110F_FM.book Page 123 Wednesday, October 3, 2001 1:43 PM Stamp F Change the stamp position, size or density. If you do not wish to change, go to step G. To change the stamp position, size or density A Press the [Change] key. B Select the desired position, size and density. C Press the [OK] key. G After you specified all the desired settings, press the [OK] key. H Press the [Cancel] key.
AdonisC2_AEcopy110F_FM.book Page 124 Wednesday, October 3, 2001 1:43 PM Copying ❒ The relationship between the direction in which you set the original and stamp Orientation/ Position is as follows: B Press the [Stamp] key. 2 C Press the [User Stamp] key. GCSTMP6E ❒ You can change the stamp position to top, bottom, left and right each way in 1mm, 0.1" steps. ⇒ “Stamp position” in P.222 “User Stamp 1/22 /2”.
AdonisC2_AEcopy110F_FM.book Page 125 Wednesday, October 3, 2001 1:43 PM Stamp B Select the desired position. Program/Delete User Stamp A Make sure that the machine is in Copy mode. B Press the {User Tools/Counter}} key. 2 C Press the [OK] key. F After you specified all the desired settings, press the [OK] key. C Press the [Copier/Document Server] key. Note ❒ To cancel the settings, press the [Cancel] key. G Press the [OK] key. D Press the [Stamp] key.
AdonisC2_AEcopy110F_FM.book Page 126 Wednesday, October 3, 2001 1:43 PM Copying F Press the [Program/Delete Stamp] key. C Enter the user stamp name with the letter keys on the display panel. 2 To program the User Stamp A Press the [Program] key. Note ❒ You can register up to 10 characters. ❒ For details on entering characters, refer to "Entering Text Characters" in the System Settings manual. D Press the [OK] key. E Enter the horizontal size of the stamp with the number keys, then press the [#] key.
AdonisC2_AEcopy110F_FM.book Page 127 Wednesday, October 3, 2001 1:43 PM Stamp F Press the [Vertical] key, and enter the vertical size in the same way as step E. G Set the user stamp on the exposure glass, and then press the [Start Scanning] key. Note ❒ The machine scans the original three times. Do not lift the document feeder until the main menu of the Copy/ Document Server features appears.
AdonisC2_AEcopy110F_FM.book Page 128 Wednesday, October 3, 2001 1:43 PM Copying ❒ You can change the Date Stamp settings with the User Tools. ⇒ P.223 “Date Stamp”. ❒ The font and size of the Date Stamp can be changed with the User Tools. ⇒ “Font” and “Size” in P.223 “Date Stamp”. ❒ You can select whether the Date Stamp is printed negative if it overlaps black parts of an image. ⇒ “Superimpose” in P.223 “Date Stamp”. ❒ For how to set the date, see “Set Date” in the System Settings manual.
AdonisC2_AEcopy110F_FM.book Page 129 Wednesday, October 3, 2001 1:43 PM Stamp C Press the [Date Stamp] key. To change the stamp position A Press the [Change] key. 2 D Press the [All Pages] or [1st Page only] to select the print page. To change the style of date B Select the desired position of the Date Stamp. A Press the [Change Format] key. C Press the [OK] key. B Select the format of date. E After you specified all the desired settings, press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 130 Wednesday, October 3, 2001 1:43 PM Copying Page Numbering Use this function to print page numbers on your copies. There are six types of Page Numbering (n is the total number of pages in your original): • P1,P2,…Pn • 1/n,2/n,...n/n • -1-,-2-,...-n• P.1,P.2,...P.n • 1, 2…n • 1-1,1-2,..
AdonisC2_AEcopy110F_FM.book Page 131 Wednesday, October 3, 2001 1:43 PM Stamp ❒ If you combine this function with the Duplex (Top to Top) function, you can change the setting to stamp on the back side in the same position as the front side. ⇒ “Duplex Back Page Stamping Position” in P.224 “Page Numbering 1/2-2/2”. ❒ If you use this function with the Combine, Magazine, or Booklet function, the page is stamped as follows.
AdonisC2_AEcopy110F_FM.book Page 132 Wednesday, October 3, 2001 1:43 PM Copying D Select the format. H Specify the page and number. If you selected (P1,P2…, -1-,-2…, P.1, P.2…, 1, 2…, ) 2 E To A Press the [First Printing Page] key, then enter the original sheet number from which to start numbering with the number keys. change the stamp position, press the [Change] key. If you do not wish to change the stamp position, go to step G. F Select the stamp position, then press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 133 Wednesday, October 3, 2001 1:43 PM Stamp E Press the [Last Number] key, then enter the page number at which to stop numbering with the number keys. C Press the [Numbering from/to] key, then enter the page number from which to start numbering with the number keys. 2 Note ❒ If you wish to print onto the last page, press the [to the end] key and go to step J. F Press the {#} } key. D Press the {#} } key.
AdonisC2_AEcopy110F_FM.book Page 134 Wednesday, October 3, 2001 1:43 PM Copying H Press the {#} } key. I Press the [OK] key. If you selected (1-1, 1-2,…) E Press the [Numbering from/to] key, then enter the page number from which to start numbering with the number keys. A Press the [First Printing Page] key, then enter the original sheet number from which to start numbering with the number keys. 2 F Press the {#} } key. G Press the [OK] key. I Press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 135 Wednesday, October 3, 2001 1:43 PM Cover/Slip Sheet Cover/Slip Sheet Using this function, you can add or insert cover or paper designate. There are four types in this function: ❖ Front Cover The first page of your originals is copied on a specific paper sheet for covers. Front Cover The first page of your originals is copied on specific paper sheet for covers, or a cover sheet is inserted before the first copy.
AdonisC2_AEcopy110F_FM.book Page 136 Wednesday, October 3, 2001 1:43 PM Copying ❒ In “Cover” of the User Tools (System Settings), if you selected “Mode Selected” for “Tray Display” setting, the machine refers to the settings in “Cover” about whether the front and back covers are copied single-sided (“1 Sided Only”) or double-sided (“Duplex Copy”).
AdonisC2_AEcopy110F_FM.book Page 137 Wednesday, October 3, 2001 1:43 PM Cover/Slip Sheet Note ❒ You can specify whether to make a copy on a cover sheet. If you select [Copy], the first and last pages will be copied on the cover sheets. If you select [Blank], a cover sheet will just be inserted before the first copy and another sheet after the last copy. ❒ When choosing [Copy], select whether the front and back covers are copied single-sided (“1 Sided Only”) or double-sided (“Duplex Copy”).
AdonisC2_AEcopy110F_FM.book Page 138 Wednesday, October 3, 2001 1:43 PM Copying B Press the [Desig./Chapter] key. Designate Use this function to have certain pages of your original copied onto slip sheets. 2 10 10 5 1 5 C Press the key to select the chapter number. 1 Preparation Before using this function, set the special paper tray for slip sheets. ⇒ “Slip Sheet 1”, “Slip Sheet 2” in the System Settings manual. Limitation ❒ You cannot use this function with Slip Sheet mode.
AdonisC2_AEcopy110F_FM.book Page 139 Wednesday, October 3, 2001 1:43 PM Cover/Slip Sheet G When you wish to finish specifying page location, press the [OK] key. Chapter The page locations you specify with this function will appear on the front of copy sheets. 2 4 6 4 1 3 1 5 2 This display shows example settings. GC SHOW OJ Note ❒ To change the number entered, enter the new number in the same way as steps C to G. H Select the paper tray containing the non-slip sheet paper.
AdonisC2_AEcopy110F_FM.book Page 140 Wednesday, October 3, 2001 1:43 PM Copying B Press the [Desig./Chapter] key. F When you finish specifying the page location, press the [OK] key. 2 C Press the [Chapter] key. This display shows example settings. Note ❒ To change the number entered, enter the new number in the same way as in steps C to E. G Set your originals, then press the D Enter the page location of the first page of the first chapter with the number keys. Then, press the {#} } key.
AdonisC2_AEcopy110F_FM.book Page 141 Wednesday, October 3, 2001 1:43 PM Slip Sheets Slip Sheets Every time the original's page changes, a slip sheet is inserted. This function can be used to insert a slip sheet automatically between each OHP transparency copied or used as a stack function. You can also copy onto the inserted slip sheets.
AdonisC2_AEcopy110F_FM.book Page 142 Wednesday, October 3, 2001 1:43 PM Copying C Select [Copy] or [Blank], followed by the [OK] key. 2 D Select the paper tray containing the non-slip sheet paper. When using OHP transparencies, open the bypass tray. E Set your originals, then press the {Start} } key.
AdonisC2_AEcopy110F_FM.book Page 143 Wednesday, October 3, 2001 1:43 PM Combination Chart Combination Chart The combination chart given below shows which modes can be used together. When you read the chart, see the following table: ❍ means that these modes can be used together. $ means that these modes cannot be used together. The mode after you select will be the mode you're working in. × means that these modes cannot be used together. The mode before you select will be the mode you're working in.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 145 Wednesday, October 3, 2001 1:43 PM 3. Document Server Overview The Document Server enables you to save documents in the machine memory and then edit and print them as you want. There are three ways to save documents. • Scanning from the document feeder • Scanning from the exposure glass • Data sent from a computer.
AdonisC2_AEcopy110F_FM.book Page 146 Wednesday, October 3, 2001 1:43 PM Document Server Process A Prepare the documents you want to save by copying, fax transmitting, scanning, and PC data. B Save the documents. • The documents are saved in the machine memory. C Print the documents, send fax, and transfer the documents and the data to PC. • You can print saved documents with any settings you desire at any time. • Scanned documents data can be transfered to PC.
AdonisC2_AEcopy110F_FM.book Page 147 Wednesday, October 3, 2001 1:43 PM Features and Benefits Features and Benefits On Demand Printing Use to print any saved document as required. ❖ Your current situation might be… • When you need to print multiple sets of documents 2-sided and stapled together, you normally print the originals, make duplex copies and then staple them together manually.
AdonisC2_AEcopy110F_FM.book Page 148 Wednesday, October 3, 2001 1:43 PM Document Server ❖ With the Document Server If you save your document in the Document Server, you can print it out at any time with the necessary print settings, such as duplex and stapling. Your documents will not be confused with those of others in the exit tray. You can store fax documents, document data so that you can print them whenever necessary. 3 Note ❒ Stapling and punching require the installation of the optional finisher.
AdonisC2_AEcopy110F_FM.book Page 149 Wednesday, October 3, 2001 1:43 PM Features and Benefits File Merge Printing You can combine multiple scanned documents to print them in one set. ❖ Your current situation might be… You want to combine several originals that are different in density, size, and paper weight, e.g. You can merge documents that were created with different applications or that were created separately on different computers.
AdonisC2_AEcopy110F_FM.book Page 150 Wednesday, October 3, 2001 1:43 PM Document Server ❖ With the Document Server Set the print order to print documents together. Merge and print fax documents, document data sent, and originals that have been scanned. Merge documents created with different applications or created on different computers. Store electronic originals created by a computer on the network, and originals that have been scanned using the document feeder.
AdonisC2_AEcopy110F_FM.book Page 151 Wednesday, October 3, 2001 1:43 PM Features and Benefits Facsimile Resend You can print or resend a sent document received by fax. This is useful when you want to send a large document that needs to be sent several times, since you do not have to scan the document each time. ❖ You current situation might be... • When you need to retransmit multiples sets of the same documents.
AdonisC2_AEcopy110F_FM.book Page 152 Wednesday, October 3, 2001 1:43 PM Document Server Operation from a Computer If you install Desk Top Binder V2 Professional or Desk Top Binder V2 Lite on your computer you can check the display of electronic data, select the finish settings and print it. You can also delete data stored in the Document Server. In addition, you can also export documents stored in the Document Server as a file on your computer.
AdonisC2_AEcopy110F_FM.book Page 153 Wednesday, October 3, 2001 1:43 PM Scanning Originals Scanning Originals You can scan the originals you want to save in the Document Server using the control panel of the machine. The originals can be set either on the exposure glass or into the document feeder. The saved documents will automatically be named in the order of scanning as “COPY0001”, “COPY0002”….
AdonisC2_AEcopy110F_FM.book Page 154 Wednesday, October 3, 2001 1:43 PM Document Server B Enter the new file name using the letter keys on the display panel. To set the password A Press the [Password] key. B Enter the password using the number keys (4 digits). 3 Reference For details on entering characters, refer to "Entering Text Characters" in the System Settings manual. C Press the [OK] key. To set the user name A Press the [User Name] key.
AdonisC2_AEcopy110F_FM.book Page 155 Wednesday, October 3, 2001 1:43 PM Scanning Originals Reference For details, see the explanations of each function in this manual. F Press the {Start}} key. The document is saved in the Document Server. The saved documents are displayed on the “Select Files to Print” display. Note ❒ If you have set your originals in the document feeder, the “Select Files to Print” display appears automatically after all originals have been scanned.
AdonisC2_AEcopy110F_FM.book Page 156 Wednesday, October 3, 2001 1:43 PM Document Server Scanning in Copy mode A Press the {Copy}} key. D Set your originals. Reference For more information on the types of originals that can be set and how to set them, ⇒ P.29 “Setting Originals”. E Make the scanning settings for the original. 3 Copy display appears. B Press the [Stored File] key. Reference For details, see the explanations of each function in this manual. F Press the {Start}} key.
AdonisC2_AEcopy110F_FM.book Page 157 Wednesday, October 3, 2001 1:43 PM Printing Saved Documents Printing Saved Documents You can print any of the documents saved in the Document Server. Follow these steps to select a document and print it out. A Press the {Document Server}} key. The “Select Files to Print” display appears. B Press the line for the document you want to print. The selected line is highlighted. Note ❒ You can search the document you desire by the file name or the user name. ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 158 Wednesday, October 3, 2001 1:43 PM Document Server D If you need to change any of the print settings, press the [Print Settings] key. 3 The “Print Settings” display appears. E Enter the required number of prints using the number keys. Note ❒ Up to 999 can be entered. ❒ To change the value entered, press the {Clear/Stop} key and enter new value.
AdonisC2_AEcopy110F_FM.book Page 159 Wednesday, October 3, 2001 1:43 PM Printing Saved Documents Sample Printing Print First Page If you print multiple sets using the Sort function, you can check if the print order or the print settings are correct by printing out only the first set using the {Sample Copy} key. You can print the first page of the document selected in the “Select Files to Print” display to check the contents.
AdonisC2_AEcopy110F_FM.book Page 160 Wednesday, October 3, 2001 1:43 PM Document Server Searching Saved Documents You can use either the [Search by File Name] or [Search by User Name] keys to search for documents stored on the document server. You can also list the stored documents in the order you prefer. If you install Desk Top Binder V2 Professional or Desk Top Binder V2 Lite on your computer, you can search and rearrange the documents from your computer.
AdonisC2_AEcopy110F_FM.book Page 161 Wednesday, October 3, 2001 1:43 PM Searching Saved Documents To Check the Details of Stored Documents A Select the document for which you want detailed information. 3 B Press the [Detail] key. The detailed information about the document is displayed. Note ❒ If you have selected several documents, use the [U U] [T T] keys to view the details of each document.
AdonisC2_AEcopy110F_FM.book Page 162 Wednesday, October 3, 2001 1:43 PM Document Server Deleting Saved Documents You should delete any of the saved documents using the control panel of the machine. This section describes how to delete saved documents. Important ❒ You can save up to 3,000 documents in the Document Server. No more documents can be saved, when there are 3,000 documents in the Document Server. You should delete unnecessary documents.
AdonisC2_AEcopy110F_FM.book Page 163 Wednesday, October 3, 2001 1:43 PM Deleting Saved Documents D Press the [Delete File] key. A confirmation dialog box appears. 3 E Press the [Delete] key to delete it. Note ❒ To cancel the delete operation, press the [Do not Delete] key.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 165 Wednesday, October 3, 2001 1:43 PM 4. Troubleshooting If Your Machine Does Not Operate as You Want General Machine Status Problem/Cause Action Please wait. A message appears when you turn on the operation switch, or change the toner bottle. Wait for the machine. Cannot detect original size. Improper original is set. ⇒ P.19 “Sizes difficult to detect”. Set custom size original on the exposure glass. ⇒ P.29 “Setting Originals on the Exposure Glass”.
AdonisC2_AEcopy110F_FM.book Page 166 Wednesday, October 3, 2001 1:43 PM Troubleshooting Machine Status Problem/Cause Action Hole punch receptacle is full. Open the door as shown and empty receptacle. Punch hole receptacle is full. Check the punch waste box and remove punch wase. ⇒ P.200 “y Removing Punch Waste”. Cannot staple paper of this size. The Staple function cannot be used the paper size selected. Select the proper paper size that can be used in Staple mode. ⇒ P.47 “Staple”.
AdonisC2_AEcopy110F_FM.book Page 167 Wednesday, October 3, 2001 1:43 PM If Your Machine Does Not Operate as You Want Document Server Problem Action You forgot your password. You can confirm your password. Press [Yes] key onto “Display Password with Stored file” temporarily, you can check the password when you selected the file. ⇒ “Display Password with Stored file” in system settings. Without the password, you cannot edit or print the document. Scan the document again.
AdonisC2_AEcopy110F_FM.book Page 168 Wednesday, October 3, 2001 1:43 PM Troubleshooting Display Problem Problem/Cause Action The display panel is off. The screen contrast knob is turned to the dark position. Set the screen contrast knob to the light position for proper viewing of the display panel. The machine is in Energy Sav- Press the {Energy Saver} key to er mode. cancel Energy Saver mode. The operation switch is turned off.
AdonisC2_AEcopy110F_FM.book Page 169 Wednesday, October 3, 2001 1:43 PM If You Cannot Make Clear Copies If You Cannot Make Clear Copies Problem Cause Copies appear dirty. The image density is too dark. Adjust the image density. ⇒ P.35 “Adjusting Copy Image Density”. Auto Image Density is not selected. The reverse side of an original image is copied. Select Auto Image Density. The image density is too dark. Adjust the image density. ⇒ P.35 “Adjusting Copy Image Density”.
AdonisC2_AEcopy110F_FM.book Page 170 Wednesday, October 3, 2001 1:43 PM Troubleshooting If You Cannot Make Copies As You Want General Problem Cause Action Copies are not stapled. There are jammed staples in the stapler. Remove jammed staples. ⇒ P.196 “e Removing Jammed Staples”. Note ❒ After removing jammed staples, staples might not be ejected the first few times you try to use the stapler. 4 170 The number of copies exceeds the capacity of the stapler. Check the stapler capacity. ⇒ P.
AdonisC2_AEcopy110F_FM.book Page 171 Wednesday, October 3, 2001 1:43 PM If You Cannot Make Copies As You Want Adjust Image Problem Cause Action In Double Copies mode, parts of the original image are not copied. Combination of original and copy paper is not correct. Select A3L for A4 originals K, A4 for A5 originals, and B5 for B6 originals. ⇒ P.110 “Double Copies”. In Border, Center, or Center/ You set the wide erased marBorder mode, parts of the gin. original image are not copied.
AdonisC2_AEcopy110F_FM.book Page 172 Wednesday, October 3, 2001 1:43 PM Troubleshooting Combine Problem Cause Action You cannot make a book from Combine Original Booklet a booklet or magazine by fold- Format or Combine Original ing copies. Magazine Format is not correct. Change the setting. ⇒ P.85 “Combine”. Parts of the image are not cop- You specified an improper reied. production ratio that does not meet the sizes of your originals and copy paper.
AdonisC2_AEcopy110F_FM.book Page 173 Wednesday, October 3, 2001 1:43 PM If You Cannot Make Copies As You Want Duplex Problem Cause Action Order of copies is not correct. You set originals in the incorrect order. When setting a stack of originals in the document feeder, the last page should be on the bottom. If you set an original on the exposure glass, start with the first page to be copied. Orientation of copies (Top to Top, or Top to Bottom) is not correct.
AdonisC2_AEcopy110F_FM.book Page 174 Wednesday, October 3, 2001 1:43 PM Troubleshooting When Memory Is Full Limitation ❒ If memory is full on either the master unit or sub-unit, Interrupt Copy will not be available. Note ❒ If you set “Memory Full Auto Scan Restart”of the User Tools to “Yes”, the memory overflow message will not be displayed, but make Connect Copy for the scanned original automatically. Connect Copy continues scanning and copying until finishing the job.
AdonisC2_AEcopy110F_FM.book Page 175 Wednesday, October 3, 2001 1:43 PM B Loading Paper B Loading Paper Note ❒ If you want to change the paper size of tray 1-2 ⇒ P.188 “Changing the Paper Size”. C Square the paper and set it in the tray. Reference Regarding paper types and sizes, ⇒ P.21 “Copy Paper”. Loading Paper in Tray 1or 2 4 A Pull out the paper tray until it stops. B Remove the back fence. Important ❒ Do not stack paper over the limit mark.
AdonisC2_AEcopy110F_FM.book Page 176 Wednesday, October 3, 2001 1:43 PM Troubleshooting E Push the paper tray in until it stops. Important ❒ Do not stack paper over the limit mark. ❒ Make sure that the paper stack is flush with the right side fence. Note ❒ Shuffle the paper before setting it in the tray. ❒ Straighten the paper, if curled or warped, before placing it in the tray. C Square the paper and set it in the 4 Loading Paper in Tray 3 or 4 tray. A Pull out the paper tray until it stops.
AdonisC2_AEcopy110F_FM.book Page 177 Wednesday, October 3, 2001 1:43 PM B Loading Paper Loading Paper in the Large Capacity Tray C Place the paper in the tray along the edge on the left. A Press the key if it is not lit. The key blinks while the bottom plate is moving down. 4 Note ❒ The Tray contains up to 1,500 sheets. B When the key stops blinking and lights up, open the top cover. Important ❒ Do not stack paper over the limit mark.
AdonisC2_AEcopy110F_FM.book Page 178 Wednesday, October 3, 2001 1:43 PM Troubleshooting D Adding Toner When D is displayed, it is time to supply toner. R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
AdonisC2_AEcopy110F_FM.book Page 179 Wednesday, October 3, 2001 1:43 PM D Adding Toner • 3: Push the green lever, and then gently pull out the holder. 2 1 Toner2 • 4: Press the toner bottle backward to raise its head, and then gently pull out the bottle. 4 2 1 Toner3 • 5: Hold a new bottle horizontally and shake it 5 or 6 times. 1 Note 5 6 ❒ Do not remove the black cap when shaking. 2 • 6: Remove the black cap. Note Toner4 ❒ Do not remove the inner cap.
AdonisC2_AEcopy110F_FM.book Page 180 Wednesday, October 3, 2001 1:43 PM Troubleshooting • 8: Push the holder until it clicks. • 9: Push down the green lever. • 10: Close the front cover of the machine.
AdonisC2_AEcopy110F_FM.book Page 181 Wednesday, October 3, 2001 1:43 PM x Clearing Misfeeds x Clearing Misfeeds R CAUTION: • The fusing section of this equipment might be very hot. You should be very careful that you don't touch this section when removing the misfed paper. Important ❒ When clearing misfeeds, do not turn off the operation switch. If you do, your copy settings are cleared. ❒ To prevent misfeeds, do not leave any torn scraps of paper within the machine.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 188 Wednesday, October 3, 2001 1:43 PM Troubleshooting Changing the Paper Size Important ❒ If you wish to change the paper size set in the optional large capacity tray (LCT), contact your service representative. ❒ Be sure to select paper size with the user tools. Otherwise, misfeeds might occur. Reference For paper sizes, weight, and capacity that can be set in each tray, ⇒ P.21 “Copy Paper”. 4 B Remove the back fence. C Remove any remaining copy paper.
AdonisC2_AEcopy110F_FM.book Page 189 Wednesday, October 3, 2001 1:43 PM Changing the Paper Size E While pressing the release lever, adjust the side fences. F Square the paper and load it into G Lock the side lever. H Adjust the back fence to the new 4 paper size. the tray. Important ❒ Do not stack paper over the limit mark. ❒ Make sure that the paper stack is flused with the right side fence. Note ❒ For 11” × 17” paper, put the back fence inside 1.
AdonisC2_AEcopy110F_FM.book Page 190 Wednesday, October 3, 2001 1:43 PM Troubleshooting 4 To adjust the paper size to one not available with the paper size selector Changing the Paper Size in Tray 3 or 4 A Set the paper size selector to the p mark on the left. B Press the {User Tools/Counter} } key. C Press the [System Settings] key. D Press the [Paper Size Setting] key. E Press the [Tray Paper Size: Tray 1] or the [Tray Paper Size: Tray 2] key. F Select your desired size. Then, press the [OK] key.
AdonisC2_AEcopy110F_FM.book Page 191 Wednesday, October 3, 2001 1:43 PM Changing the Paper Size D Re-position the side fences to the paper size you want to use. Note ❒ Shuffle the paper before setting it in the tray. ❒ Make sure the leading corners of the paper are under the corners. G Adjust the back fence to the new paper size. E Fasten the fences with screws. 4 Note ❒ For 11” × 17” paper, put the back fence inside 1. F Square the paper and load it into the tray.
AdonisC2_AEcopy110F_FM.book Page 192 Wednesday, October 3, 2001 1:43 PM Troubleshooting d Adding Staples R CAUTION: • Our products are engineered to meet high standards of quality and functionality, and we recommend that you only use the expendable supplies available at an authorized dealer. Important ❒ If you use a staple cartridge other than that recommended, staple failure or staple jams might occur. 1000-Sheet Finisher 4 • 1: Open the front cover. fin101EE • 2: Remove the cartridge.
AdonisC2_AEcopy110F_FM.book Page 193 Wednesday, October 3, 2001 1:43 PM d Adding Staples • 4: Push in the new refill until it clicks. fin104EE • 5: Pull out the ribbon. 4 fin105EE • 6: Reinstall the cartridge. fin106EE • 7: Close the front cover.
AdonisC2_AEcopy110F_FM.book Page 194 Wednesday, October 3, 2001 1:43 PM Troubleshooting 2 Tray Finisher • 1: Open the front cover of the finisher. • 2: Hold the green lever and pull out the cartridge gently. 4 • 3: Hold the both sides of the cartridge. • 4: Pull up the upper unit of the cartridge. • 5: Take out the empty refill in the arrow direction. • 6: Align the arrows on the new refill and the cartridge, and then push in the refill until it clicks.
AdonisC2_AEcopy110F_FM.book Page 195 Wednesday, October 3, 2001 1:43 PM d Adding Staples • 7: Hold down the upper unit to the cartridge gently. • 8: Pull out the ribbon. 4 • 9: Hold the green lever and reinstall the cartridge until it clicks. • 10: Close the front cover of the finisher.
AdonisC2_AEcopy110F_FM.book Page 196 Wednesday, October 3, 2001 1:43 PM Troubleshooting e Removing Jammed Staples Note ❒ Staples might be jammed because of curled copies. In this case, try turning the copy paper over in the tray. If there is no improvement, change the copy paper with less curls. ❒ After removing jammed staples, staples might not be ejected the first few times you try to use the stapler. 1000-Sheet Finisher • 1: Open the front cover. 4 fin108EE • 2: Remove the cartridge.
AdonisC2_AEcopy110F_FM.book Page 197 Wednesday, October 3, 2001 1:43 PM e Removing Jammed Staples • 4: Remove the jammed staples. fin111EE • 5: Reinstall the cartridge. 4 fin112EE • 6: Close the front cover.
AdonisC2_AEcopy110F_FM.book Page 198 Wednesday, October 3, 2001 1:43 PM Troubleshooting 2 Tray Finisher • 1: Open the front cover of the finisher. • 2: Hold the green lever and pull out the cartridge gently. 4 • 3: Pull up the knob of the cartridge. • 4: Take out all staples slid from the cartridge. • 5: Pull down the knob of the cartridge until it clicks.
AdonisC2_AEcopy110F_FM.book Page 199 Wednesday, October 3, 2001 1:43 PM e Removing Jammed Staples • 6: Hold the green lever and reinstall the cartridge until it clicks. • 7: Close the front cover of the finisher.
AdonisC2_AEcopy110F_FM.book Page 200 Wednesday, October 3, 2001 1:43 PM Troubleshooting y Removing Punch Waste Note ❒ While “Hole punch receptacle is full.” is displayed, you cannot use the Punch function. C Reinstall the punch waste box. A Open the front cover of the 2 Tray finisher. 4 Note ❒ If you do not, “Hole punch receptacle is full.” is still displayed. B Pull out the punch waste box and remove punch waste. D Close the front cover of the 2 Tray finisher. “Hole Punch Receptacle Full.
AdonisC2_AEcopy110F_FM.book Page 201 Wednesday, October 3, 2001 1:43 PM 5. User Tools (Copy/ Document Server Features) Accessing the User Tools (Copy/ Document Server Features) This section is for the key operators in charge of this machine. You can change or set the machine's default settings. C Select the desired menu and press the key. Preparation After using the User Tools, be sure to exit from the User Tools. The selected key is highlighted.
AdonisC2_AEcopy110F_FM.book Page 202 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) Exiting From the User Tools A After changing the User Tools settings, press the [Exit] key on the User Tools Main Menu. Changing the User Tools is completed, and the machine is ready for copying. 5 Note ❒ To exit from the change of the machine's default settings and return to Copy mode, press the {User Tools/Counter} key.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 206 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) General Features 1/4 ❖ Auto Paper Select Priority As a default setting, Auto Paper Select is selected. You can cancel this setting. Note ❒ Default: Yes ❖ Auto Tray Switching If you load paper of the same size in two or more trays, the machine automatically shifts to another tray when the tray in use runs out of paper (when Auto Paper Select is selected.
AdonisC2_AEcopy110F_FM.book Page 207 Wednesday, October 3, 2001 1:43 PM General Features 1/4 ❖ Original Mode Display You can choose whether the original modes are shown on the initial display. Note ❒ Default: Display ❒ If you choose “Hide”, the display is shown as below. ❖ Auto Image Density Priority You can turn the Auto Image Density on or off for each of the original types (Text, Text/Photo, Photo, Pale, and Generation Copy).
AdonisC2_AEcopy110F_FM.book Page 208 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) • Text/Photo When there are photo(s) and text on the original, determine whether the photo or text takes priority. Note ❒ Default: Normal ❒ [Custom Setting] is the value set during service setup. ❒ [Normal] achieves a good balance between text and photos. • Photo For a photo original, adjust the finish quality level to match the type of photo original.
AdonisC2_AEcopy110F_FM.book Page 209 Wednesday, October 3, 2001 1:43 PM General Features 2/4 General Features 2/4 ❖ Duplex Mode Priority You can select the type of the Duplex function effective when the machine is turned on, Energy Saver mode is off, or Auto Reset is on. Note ❒ Default: • Metric version: 1 Sided→1 Sided • Inch version: 1 Sided→2 Sided ❖ Copy Orientation in Duplex Mode You can set the copy orientation when making two-sided copies.
AdonisC2_AEcopy110F_FM.book Page 210 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) ❖ Job End Call You can choose whether or not the beeper sounds when copying is complete. If the "Panel Tone" of the User Tools (System Settings) settings is "Off", the machine beeps to notify you that the machine did not complete a job for reasons such as copying was interrupted, the paper tray ran out of paper or a paper jam occurred.
AdonisC2_AEcopy110F_FM.book Page 211 Wednesday, October 3, 2001 1:43 PM General Features 3/4 General Features 3/4 ❖ Copy Function Key: F1-F5 You can register frequently used functions in Function Keys F1 to F5.
AdonisC2_AEcopy110F_FM.book Page 212 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) General Features 4/4 ❖ Document Server Storage Key: F1–F5 You can reqister frequently used functions in Function keys F1 to F5. You can also change the registered functions.
AdonisC2_AEcopy110F_FM.book Page 213 Wednesday, October 3, 2001 1:43 PM Reproduction Ratio 1/2 Reproduction Ratio 1/2 ❖ Shortcut R/E You can register up to three frequently used Reduce/Enlarge ratios other than the fixed Reduce/Enlarge ratio and have them shown on the initial display. You can also change the registered Reduce/Enlarge ratios.
AdonisC2_AEcopy110F_FM.book Page 214 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) Reproduction Ratio 2/2 ❖ Reduce 1-6 You can customize the reduction ratios available when you press the [Reduce/ Enlarge] key followed by the [Reduce] key.
AdonisC2_AEcopy110F_FM.book Page 215 Wednesday, October 3, 2001 1:43 PM Reproduction Ratio 2/2 ❖ R/E Priority Specify which Reduce, Enlarge or Input Ratio is shown on the display panel with priority when the [Reduce/Enlarge] key is pressed.
AdonisC2_AEcopy110F_FM.book Page 216 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) Edit 1/2 ❖ Front Margin: Left/Right You can specify left and right margins on the front side of copies in Margin Adjust mode. Note ❒ Default: • Metric version: Left 5mm • Inch version: Left 0.2" ❖ Back Margin: Left/Right You can specify left and right margins on the back side of copies in Margin Adjust mode. Note ❒ Default: • Metric version: Right 5mm • Inch version: Right 0.
AdonisC2_AEcopy110F_FM.book Page 217 Wednesday, October 3, 2001 1:43 PM Edit 1/2 ❖ 1 sided→ →2 sided Auto Margin:T to T In 1 sided → 2 sided Duplex mode, you can specify whether to automatically set the margins on the back side. The margin is set to the same value of “Back Margin: Left/Right”. Note ❒ Default: • Metric version: Right 5mm • Inch version: Right 0.
AdonisC2_AEcopy110F_FM.book Page 218 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) Edit 2/2 ❖ Image Repeat Separation Line You can select a separation line in Image Repeat mode from None, Solid, Broken A, Broken B, or Crop Marks. • None • Solid • Broken A 5 • Broken B • Crop Marks Note ❒ Default: None ❖ Double Copies Separation Line You can select a separation line in Double Copy mode from None, Solid, Broken A, Broken B,or Crop Marks.
AdonisC2_AEcopy110F_FM.book Page 219 Wednesday, October 3, 2001 1:43 PM Edit 2/2 • Broken A • Broken B • Crop Marks Note ❒ Default: None ❖ Separation Line in Combine You can select a separation line in Combine mode from None, Solid, Broken A, Broken B, or Crop Marks.
AdonisC2_AEcopy110F_FM.book Page 220 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) ❖ Front Cover Copy in Combine You can specify whether to make a combined copy on the front cover sheet when you select Front Cover copy mode. Note ❒ Default: Combine ❖ Designated Slip Sheet Copy in Combine You can specify whether to make a combined copy on the inserted slip sheets in Desig./Chapter Copy mode.
AdonisC2_AEcopy110F_FM.book Page 221 Wednesday, October 3, 2001 1:43 PM Stamp Stamp Background Numbering ❖ Size You can set the size of the numbers. Note ❒ Default: Normal • Small • Normal • Large ❖ Density You can set the density of the numbers. 5 Note ❒ Default: Normal Preset Stamp 1/4-4/4 ❖ Stamp Priority You can select the stamp type priority detected in Stamp mode. Note ❒ Default: Copy ❖ Stamp Language You can select the language of the message that is printed in Stamp mode.
AdonisC2_AEcopy110F_FM.book Page 222 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) • Inch Version: • Position: Top right • Top Margin: 1.0" • Right Margin: 1.0" ❖ Stamp Format You can adjust the size, density and print page for the stamp. • Size You can set the size of the stamp. Note ❒ Default: 1X • Density You can set the pattern used to print the stamp. Note ❒ Default: Normal ❒ Normal: The stamp is printed on the image. You cannot confirm which parts overlap the image.
AdonisC2_AEcopy110F_FM.book Page 223 Wednesday, October 3, 2001 1:43 PM Stamp • Inch version: • Position: Top right • Top Margin: 1.0" • Right Margin: 1.0" ❖ Stamp Format You can adjust the print page for User Stamp 1 to 4 you registered. Note ❒ Default: All Pages Date Stamp ❖ Format You can select the date format for Date Stamp mode. 5 Note ❒ Default: • Metric version: DD/MM/YYYY • Inch version: MM/DD/YYYY ❖ Font You can select the Date Stamp font.
AdonisC2_AEcopy110F_FM.book Page 224 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) ❖ Stamp Setting You can select whether the date is printed on the first page or all pages. Note ❒ Default: All Pages ❖ Size You can set the Date Stamp size. Note ❒ Default: Auto ❒ This setting is linked with Page Numbering. ❖ Superimpose You can select whether the Date Stamp is printed negative when it overlaps black parts of the image.
AdonisC2_AEcopy110F_FM.book Page 225 Wednesday, October 3, 2001 1:43 PM Stamp ❖ Duplex Back Page Stamping Position You can set the position of the duplex back page number that is printed in Duplex mode. Note ❒ Default: Opposite Position ❖ Page Numbering in Combine You can set how the pages are numbered when you use the Combine function and Page Numbering function together.
AdonisC2_AEcopy110F_FM.book Page 226 Wednesday, October 3, 2001 1:43 PM User Tools (Copy/Document Server Features) Input/Output ❖ Switch to Batch (SADF) You can select Batch mode or SADF mode when you press the Special Original key. ❖ SADF Auto Reset When you set one original at a time in the document feeder, the Auto Feed indicator lights for a selected time after an original is fed to show that the document feeder is ready for another original. You can adjust this time from 3 seconds to 99.
AdonisC2_AEcopy110F_FM.book Page 227 Wednesday, October 3, 2001 1:43 PM Input/Output ❖ Select Stack Function Specify which Stack or Rotate Sort is shown on the initial display with priority. Note ❒ Default: Stack ❒ The optional finisher or booklet finisher is required to use this function. ❖ Select Stapling Position Specify which Top 2 staples or Bottom is shown on the initial display with priority. Note ❒ Default: Top 2 staples ❒ The optional 2 Tray Finisher is required to use this function.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.book Page 229 Wednesday, October 3, 2001 1:43 PM 6. REMARKS Do's And Don'ts R CAUTION: • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. Important ❒ If you want to unplug the power cord or turn off the main power switch, make sure that the remaining memory space indicates 100% on the display for facsimile mode.
AdonisC2_AEcopy110F_FM.book Page 230 Wednesday, October 3, 2001 1:43 PM REMARKS Where to Put Your Machine Machine Environment Environments to avoid Your machine's location should be carefully chosen because environmental conditions greatly affect its performance. • Locations exposed to direct sunlight or strong light (more than 1,500 lux). • Locations directly exposed to cool air from an air conditioner or heated air from a heater.
AdonisC2_AEcopy110F_FM.book Page 231 Wednesday, October 3, 2001 1:43 PM Where to Put Your Machine Limitation ❒ Carefully move the machine, If not, the machine might be damaged or stored file might be deleted. ❒ Do not take off the holding stand. ❒ Avoid any strong shocking to the machine, the hard disk might be damaged, and stored files will be deleted. For precautionaly reasons files should be copied to another local computer.
AdonisC2_AEcopy110F_FM.book Page 232 Wednesday, October 3, 2001 1:43 PM REMARKS Maintaining Your Machine If the exposure glass, platen cover, or document feeder belt is dirty, you might not be able to make copies as you want. Clean them if you find them dirty. Cleaning the Document Feeder ❖ Cleaning the machine Wipe the machine with a soft, damp cloth. Then, wipe it with a dry cloth to remove the water. Important ❒ Do not use chemical cleaner or organic solvent, such as thinner or benzene.
AdonisC2_AEcopy110F_FM.book Page 233 Wednesday, October 3, 2001 1:43 PM 7.
AdonisC2_AEcopy110F_FM.book Page 234 Wednesday, October 3, 2001 1:43 PM Specification ❖ Copy paper size: • Trays: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L • Bypass: A3L – A6L, 11" × 17"L – 51/2" × 81/2"L • Bypass (custom size): Vertical: 100 – 297mm, 4.0" – 11.7" Horizontal: 148 – 600mm, 5.9" – 23.6" • Duplex: A3L – A5L, 11" × 17"L – 51/2" × 81/2"L (impossible on A5K, 51/2" × 81/2" K) • LCT: A4K, 81/2" × 11"K ❖ Copy paper weight: • Paper tray: 64 – 105g/m2, 17 – 28 lb. • Bypass tray: 52 – 163g/m2, 14 lb.
AdonisC2_AEcopy110F_FM.book Page 235 Wednesday, October 3, 2001 1:43 PM Mainframe ❖ Reproduction ratio: Preset reproduction ratios: Metric version Enlargement Inch version 400% 400% 200% 200% 141% 155% 122% 129% 115% 121% Full Size 100% 100% Reduction 93% 93% 82% 85% 75% 78% 71% 73% 65% 65% 50% 50% 25% 25% Zoom: From 25 to 400% in 1% steps. ❖ Maximum continuous copy run: 999 sheets 7 ❖ Copy paper capacity: • Tray 1, 2: 500 sheets (80g/m2, 20 lb.
AdonisC2_AEcopy110F_FM.book Page 236 Wednesday, October 3, 2001 1:43 PM Specification ❖ Dimensions (W × D × H up to exposure glass): Type 1, 2: 670 × 650 × 720mm, 26.4" × 25.6" × 28.3" ❖ Space for mainframe (W × D): • Type 1, 2: 980 × 650mm, 38.6" × 25.
AdonisC2_AEcopy110F_FM.book Page 237 Wednesday, October 3, 2001 1:43 PM Document Feeder (Option) Document Feeder (Option) ❖ Mode: ADF mode, Batch mode, Mixed Size mode, Custom Size originals mode ❖ Original size: • A3L – B6KL (2 sided original are impossible for B6KL) • 11" × 17"L – 51/2" × 81/2"KL ❖ Original weight: • 1-sided originals: 40 – 128g/m2 (11 – 34 lb.) • 2-sided originals: 52 – 105g/m2 (14 – 28 lb.) (Duplex) ❖ Number of originals to be set: 80 sheets (80g/m2, 20 lb.) or less than 11mm, 0.
AdonisC2_AEcopy110F_FM.book Page 238 Wednesday, October 3, 2001 1:43 PM Specification 1000-Sheet Finisher (Option) ❖ Paper size: A3L, B4L, A4KL, B5KL, A5KL, B6L, A6L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"L ❖ Paper weight: 52 – 157g/m2, 14 – 42 lb. ❖ Stack capacity: • 1,000 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.) • 500 sheets (B4L, 81/2" × 14"L or larger) (80g/m2, 20 lb.) ❖ Staple capacity: • 30 sheets (A4K, 81/2" × 11"K or smaller) (80g/m2, 20 lb.
AdonisC2_AEcopy110F_FM.book Page 239 Wednesday, October 3, 2001 1:43 PM 2 Tray Finisher (Option) 2 Tray Finisher (Option) Finisher Shift Tray 1: ❖ Paper size: A3L, B4L, A4KL, B5KL, A5KL, B6L, A6L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL ❖ Paper weight: 52 – 157g/m2, 14 – 42 lb. ❖ Stack capacity: • 500 sheets (A4KL, B5KL, A5K, 81/2" × 11"KL) (80g/m2, 20 lb.) • 250 sheets (A3L, B4L, 81/2" × 14"L, 11" × 17"Ls) (80g/m2, 20 lb.) • 100 sheets (A5L, 51/2" × 81/2"KL) (80g/m2, 20 lb.
AdonisC2_AEcopy110F_FM.book Page 240 Wednesday, October 3, 2001 1:43 PM Specification ❖ Staple position: • 1 staple – 3 positions • 2 staples – 1 position ❖ Power consumption: Less than 60W (power is supplied from the main frame.) ❖ Dimensions (W × D × H): 680 × 620 × 1.030mm, 26.7" × 24.4" × 40.5" ❖ Weight: Approx. 55kg, 121.2 lb.
AdonisC2_AEcopy110F_FM.book Page 241 Wednesday, October 3, 2001 1:43 PM Punch Kit (Option) Punch Kit (Option) ❖ Paper size • 2 holes: A3L – A5KL, 11" × 17"L, 81/2" × 14"L – 51/2" × 81/2"KL • 3 holes: A3L, B4L, A4K, B5K, 11" × 17"L, 81/2" × 11"K • 4 holes: • Metric version: A3L, B4L, A4K, B5K, 11" × 17"L, 81/2" × 11"K • Scandinavian version: A3L – A5K, 11" × 17"L, 81/2" × 14"L – 51/2" × 81/2"K ❖ Paper weight: • 4 holes: 52 – 163g/m2, 14 lb. – 43 lb. • 2 or 3 holes: 52 – 163g/m2, 14 lb. – 43 lb.
AdonisC2_AEcopy110F_FM.book Page 242 Wednesday, October 3, 2001 1:43 PM Specification Internal tray 2 (1 bin tray) (Option) ❖ Number of bins: 1 ❖ Available paper size: A3L, B4L, B5KL, A5L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2" L ❖ Paper capacity: 125 sheets (80g/m2, 20 lb.) ❖ Copy paper weight: 60 – 105g/m2 (16 – 28lb.) ❖ Maximum power consumption: Less than 15 W (power is supplied from the main frame.) ❖ Dimensions (W × D × H): 470 × 550 × 110mm, 18.6" × 21.7" × 4.4" ❖ Weight: Approx.
AdonisC2_AEcopy110F_FM.book Page 243 Wednesday, October 3, 2001 1:43 PM Extarnal Tray (Option) Extarnal Tray (Option) ❖ Dimensions (W × D × H): 265 × 395 × 65mm, 10.4" × 15.5" × 2.5" ❖ Weight: Approx. 600 g, 1.3 lb Note ❒ Specifications are subject to change without notice.
AdonisC2_AEcopy110F_FM.book Page 244 Wednesday, October 3, 2001 1:43 PM Specification Large Capacity Tray (LCT) (Option) ❖ Paper size: A4K, 81/2" × 11"K ❖ Paper weight: 60 – 105g/m2, 16 – 24 lb. ❖ Paper capacity: 1,500 sheets (80g/m2, 20 lb.) ❖ Power consumption Maximum. 40 W (power is supplied from the mainframe.) ❖ Dimensions (W × D × H, option unit): 390 × 500 × 390mm, 15.3" × 19.6" × 15.3" ❖ Weight: Approx. 17 kg, 37.5 lb. Note ❒ Specifications are subject to change without notice.
AdonisC2_AEcopy110F_FM.book Page 245 Wednesday, October 3, 2001 1:43 PM Paper tray unit (Option) Paper tray unit (Option) ❖ Copy paper weight: 60 – 105g/m2 (16 – 28 lb.) ❖ Available paper size: A3L, B4L, A4KL, B5KL, A5L, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2" L, 81/4" × 14"L, 11" × 14"L, 71/4" × 101/2" L, 8" × 13"L, 8" × 101/2"KL, 81/2" × 13"L, 8" × 101/2"KL, 81/4" × 13"L ❖ Maximum power consumption: Less than 50 W (power is supplied from the main frame.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
AdonisC2_AEcopy110F_FM.
