Instructions / Assembly

ManualsBrandsRIDGID ManualsPlumbing1 HP Ridgid Stainless Steel Smart Dual Suction Sump Pump

PUMP SPECIFICATIONS

POWER SUPPLY REQUIREMENTS 120 V, 60 Hz

MOTOR Single Phase, Dielectric Oil Filled

HORSEPOWER

1 HP ....................

CIRCUIT REQUIREMENTS 15 A (minimum)

DIMENSIONS

11-1/2 in. high x 9-3/4 in. base

ON LEVEL (FACTORY SET) Approximately 9.5 in.

OFF LEVEL (FACTORY SET)

Approximately 4.5 in.

Smart Submersible Sump Pump

Please read and save these instructions. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property

damage! Retain instructions for future reference.

Installation Manual 1000RSDSSmart

PERFORMANCE GAL/HR

Model HP

Discharge Head (Lift Distance)

0 ft 5 ft 10 ft 15 ft 20 ft

1000RSDSSmart 1 6600 6240 5640 4920 3660

www.homedepot.com

CONSTRUCTION

MOTOR HOUSING Stainless Steel

VOLUTE Cast Iron

IMPELLER

Glass Reinforced Thermoplastic

SHAFT Steel

DISCHARGE

1-1/2 in. NPT

CONTROLLER SPECIFICATIONS

SWITCH Solid State Air Switch

CONNECTIVITY Wi-Fi + BLE

AIR TUBE

PVC

Summary of content (12 pages)

PAGE 1
Smart Submersible Sump Pump Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
INSTALLATION MANUAL SUMP PUMP DESCRIPTION Sump pumps are automatic pumps used to remove ground water from sump pits. The most common application is for basement drainage to prevent flooding in residential buildings. These pumps are designed to pump clear water only. With the innovative and reliable Air Switch, your pump is no longer limited by the mechanical cycles of traditional float switch style pumps.
PAGE 3
INSTALLATION MANUAL NEVER HANDLE A PUMP or motor with wet hands or when standing on a wet or damp floor while the pump is plugged into the power supply. NE JAMAIS MANIPULER UNE POMPE ou un moteur de pompe avec les mains mouillées ou debout dans l’eau ou sur une surface humide. RISK OF ELECTRIC SHOCK. This pump has not been investigated for use in swimming pool and marine areas. RISQUE DE CHOC ÉLECTRIQUE.
PAGE 4
INSTALLATION MANUAL DO NOT USE THIS PUMP IN MUD, SAND, CEMENT, OIL CHEMICALS, GREY WATER, OR ANY OTHER WATER THAT IS NOT CLEAR GROUND WATER. NE PAS UTILISER CETTE POMPE DANS LA BOUE, LE SABLE, LE CIMENT, LES PRODUITS CHIMIQUES À L’HUILE, DE L’EAU GRISÂTRE OU TOUTE AUTRE EAU QUI N’EST PAS DE L’EAU CLAIRE SOUTERRAINE. DO NOT USE SUMP PUMPS TO HANDLE RAW SEWAGE. NE PAS UTILISER DE POMPES DE PUISARD POUR POMPER LES EFFLUENTS.
PAGE 5
INSTALLATION MANUAL DECLARACIÓN SOBRE INTERFERENCIAS DE LA FCC Este equipo ha sido probado y se ha comprobado que cumple con los límites de un dispositivo digital de clase B, de acuerdo con la sección 15 de las normas de la FCC. Estos límites están diseñados para proporcionar una protección razonable contra interferencias perjudiciales en una instalación residencial.
PAGE 6
INSTALLATION MANUAL Vertical Submersible Sump 11 2 3 4 6. Install a check valve (required) to prevent back-flow. The RIDGID® check valve (57028-001) may be positioned just above the basin to allow easy removal of the pump for cleaning and service. 1 10 12 5 MINIMUM BASIN HEIGHT 22 IN. 6 7 8 9 ON LEVEL 11 IN. DIAMETER MIN. APPROX. 9 IN. OFF LEVEL APPROX. 4 IN. 1. GFCI OUTLET 7. SUMP PUMP 2. CHECK VALVE 8. AIR SWITCH 3. VENT PIPE 9. BASIN 4. GASKET/BASIN LID 10.
PAGE 7
INSTALLATION MANUAL LED LIGHT DISPLAY (CHECK YOUR APP FOR SPECIFIC REAL TIME PUMP INFORMATION) Color Symptom/Possible Cause(s) Suggested Remedies Green 1. Good 1. Your pump is good, there is nothing needed Yellow 1. A clogged pump inlet 1. Open your sump pit and inspect the pump. Make sure the inlet screen is free of debris and there is nothing blocking the fow of water into the pump. 2. Electrical voltage or polarity issue detected 2.
PAGE 8
INSTALLATION MANUAL DEVICE ACTIVATION INSTRUCTIONS NOTE: Make sure your Wi-Fi and Bluetooth is connected. 1. Download the SmartSumpbyRIDGID App from your device’s app store. 2. Open the SmartSumpbyRIDGID App and click “+ Add Device” to begin device activation. 3. Select your RIDGID® device. 4. Verify that the status LED on the device is blinking yellow. Click Next to continue. 5. Allow access to your devices camera and use your camera to scan the QR code located on the front of your device.
PAGE 9
INSTALLATION MANUAL TROUBLESHOOTING WARNINGS 1. Submersible pump models have permanently lubricated bearings and require no additional lubrication. 2. Submersible pumps contain dielectric oil for cooling. Dielectric oil can be harmful to the environment. Follow state environmental laws when disposing of pump. ALWAYS DISCONNECT THE PUMP FROM POWER SUPPLY before installing, servicing or making any adjustments. 3.
PAGE 10
INSTALLATION MANUAL TROUBLESHOOTING CHART (CONTINUED) Symptoms Possible Cause(s) Suggested Remedies Pump trips GFCI 1. Bad GFCI 1. Contact an electrician to replace GFCI 2. Bad pump 2. Replace pump Pump operates 1. Worn bearings noisily or vibrates 2. Impeller broken excessively 3. Piping attachments to building structure too rigid or too loose 1. Replace pump Pump will not shut off 1. Switch 1. Run system test. Also, make sure your Air Tube is not constricted. 2. Switch obstructions 2.
PAGE 11
INSTALLATION MANUAL USING YOUR DIGITAL CONTROLLER MUTE ALARM: Will silence alarm for 12 hours. For custom mutes times, open the companion app while the alarm is active and press the alarm icon next to the alert pop-up. SYSTEM TEST: While your pump will automatically run periodic system tests; you can always force a system test via the controller or the companion app. A complete System Test which analyzes all aspects of Pump Health will be performed at Water Level 2 or higher.
PAGE 12
INSTALLATION MANUAL INSTALLATION MANUAL ADDRESS PARTS CORRESPONDENCE TO: RIDGID® Pumps 101 Production Drive Harrison, OH 45030 U.S.A. FOR REPLACEMENT PARTS OR CUSTOMER SUPPORT, CALL 1-877-9RIDGID® Please provide following information: - Model number - Serial number on cord tag (not to be removed) - Part description and number as shown in parts list Thank you for making RIDGID® Pumps a key part of your home maintenance program.