User Guide

K-3800 Drain Cleaning Machine
Autofeed Assembly
Proper cleaning and lubrication of the autofeed assembly
is advised for long, trouble-free operation. After each
use, hose out autofeed assembly with water and lubricate
with lightweight machine oil.
Cables
Cables should be thoroughly flushed with water to prevent
damaging effects of sediment and drain cleaning com-
pounds. Periodically lubricate cables and couplings with
RIDGID Cable Rust Inhibitor.
When not in use, store cables indoors to prevent deteri-
oration by the elements.
Cables should be replaced when they become severely
corroded or worn. A worn cable can be identified when
outside coils of cable become flat.
Machine Storage
Motor-driven equipment must be kept in-
doors or well covered in rainy weather. Store the machine
in a locked area that is out of reach of children and peo-
ple unfamiliar with drain cleaners. This machine can
cause serious injury in the hands of untrained users.
Service and Repair
WARNING
The “Maintenance Instructions” will take care of most of
the service needs of this machine. Any problems not
addressed by this section should only be handled by an
authorized RIDGID service technician.
Tool should be taken to a RIDGID Independent Auth-
orized Service Center or returned to the factory. All re-
pairs made by Ridge service facilities are warranted
against defects in material and workmanship.
When servicing this machine, only identi-
cal replacement parts should be used. Failure to follow
these instructions may create a risk of electrical shock or
other serious injury.
Refer to Ridge Tool catalog for complete listing of tools
and accessories.
Maintenance Instructions
WARNING
Make sure machine is unplugged from electrical
system before making any adjustment.
Lubrication
Grease all exposed moving and rotating parts such as
guide tube assembly as required.
Ridge Tool Company 13
Catalog Model
No. No. Description
62990 T-201 Straight Auger, 5″ Long
62995 T-202 Bulb Auger, 1
1
/
8
″ O.D.
63000 T-203 Bulb Auger,
7
/
8
″ O.D.
63065 T-217 Drop Head, 4″ Long
54837 T-204 “C” Cutter - 1″
63005 T-205 “C” Cutter - 1
3
/
8
″
63010 T-206 Funnel Auger, 3″ Long
63015 T-207 Spiral Cutter, 1
1
/
4
″
63020 T-208 Spiral Cutter, 1
1
/
2
″
63025 T-209 Spiral Cutter, 2″
63030 T-210 Spade Cutter, 1″
63035 T-211 Spade Cutter, 1
3
/
8
″
63040 T-212 Spade Cutter, 1
3
/
4
″
63045 T-213 4-Blade Cutter, 1″
63050 T-214 4-Blade Cutter, 1
3
/
8
″
63055 T-215 4-Blade Cutter, 1
3
/
4
″
63060 T-216 Chain Knocker, 2″
49002 T-260 Tool Set:
- T-202 Bulb Auger
- T-205 “C” Cutter
- T-211 Spade Cutter
- A-13 Pin Key
Tools – Fit C-31, C-32 and C-33 Cables
Catalog Model
No. No. Description
62850 T-101 Straight Auger
62855 T-102 Funnel Auger
27642 T-125 Retrieving Auger
62865 T-104 “H” Cutter, 2
1
/
2
″
62870 T-105 Grease Cutter, 2
1
/
2
″
62875 T-106 Grease Cutter, 3
1
/
2
″
62880 T-107 Spade Cutter, 1
3
/
4
″
62930 T-112 4-Blade Cutter, 1
3
/
4
″
62935 T-113 4-Blade Cutter, 3″
62940 T-114 Chain Knocker
54842 T-141 Knife Blade Cutter, 1
1
/
2
″
54852 T-142 Knife Blade Cutter, 2
1
/
2
″
54992 T-270 Tool Set:
- T-102 Funnel Auger
- T-142 Knife Blade Cutter
- T-107 Grease Cutter
- A-12 Pin Key
Tools – Fits C-44, C-45, and C-46 Cables
WARNING
WARNING