Operator’s Manual With Te ch n o l ogy WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and follow the contents of this manual may result in electrical shock, fire, and/or serious personal injury. For support and additional information about using your Compact M40 go to support.seesnake.com/compact-m40 or scan this QR code.
Table of Contents Introduction Regulatory Statements ����������������������������������������������������������������������������������������������������������������������������������������������� 3 Safety Symbols ����������������������������������������������������������������������������������������������������������������������������������������������������������� 3 General Safety Rules Work Area Safety ������������������������������������������������������������������������������������������������������
Introduction The warnings, cautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Regulatory Statements The EC Declaration of Conformity (890-011320.10) will accompany this manual as a separate booklet when required. This device complies with Part 15 of FCC rules.
General Safety Rules WARNING Personal Safety • Stay alert, watch what you are doing, and use common sense when operating equipment. Do not use equipment while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating equipment may result in serious injury. • Dress properly. Do not wear loose clothing or jewelry. Loose clothes, jewelry, and long hair can be caught in moving parts. Read all safety warnings and instructions.
Equipment Use and Care • Do not force equipment. Use the correct equipment for your application. The correct equipment does the job better and more safely. Pre-Operation Inspection WARNING • Do not use equipment if the power switch does not turn it on and off. Any equipment that cannot be controlled with the power switch is dangerous and must be repaired. • Disconnect the plug from the power source and/or the battery pack from the equipment before making adjustments, changing accessories, or storing.
Compact M40 Overview Description The RIDGID® SeeSnake® Compact M40 camera reel offers fast, easy setup and can take on the most diverse and demanding inspection conditions.The Compact M40 features a self-leveling camera at the end of a moderately stiff cable that offers a good compromise between stiffness and the ability to navigate through turns. The FleXmitter® sonde helps locate points of interest in the pipe.
Specifications Weight 9.8 kg [22 lb] Dimensions Specifications Pipe Capacity § 38 mm to 203 mm [1.5 in to 8 in] System Cable Length 3 m [10 ft] Length 626 mm [25 in] Depth 360 mm [14 in] Temperature ‡ -10°C to 50°C [14°F to 122°F] Height 429 mm [16 in] Storage temperature -10°C to 70°C [14°F to 158°F] Drum diameter 432 mm [17 in] Ingress protection (without monitor) IP×6 Relative humidity 5 to 95 percent Altitude 4,000 m [13,123 ft] Camera depth rating Waterproof to 100 m [328.
Specific Safety Information System Components WARNING Frame Docking System This section contains important safety information that is specific to the Compact M40. Read these precautions carefully before using the equipment to reduce the risk of electrical shock, fire, and/or serious injury.
Operating Instructions Inspection Overview Placement To perform a pipe inspection, connect any SeeSnake monitor to the reel, power on the system, push the push cable through the pipe, and observe the display. Set up your SeeSnake system near the pipe entrance so you can manipulate the push cable while viewing the monitor. Make sure that the drum can spin freely.
CS6x Versa Docking System WARNING Do not carry the Compact M40 by the monitor’s mounting frame or kickstand. Doing so can cause the monitor to disengage from the docking system and may result in property damage and/or serious injury. 1. Place the Compact M40 so you can grasp both quick-release knobs. 2. Pull both knobs out and away from the docking fins. In the same motion as pulling the knobs out, turn the knobs together in either direction to disengage the locks.
System Cable Removal System Cable Installation 1. Disconnect the system cable from the reporting monitor and remove the monitor from the docking system. 2. Unwrap the system cable from the cable wraps. 3. Pop the frame cable anchor off the frame and unhook the system cable from the frame hook. Cable Anchor 1. Align the arrow on the slip-ring dial with the unlock symbol on the frame and insert the slip-ring dial into the slip-ring cavity. 2. Turn the slip-ring dial to the locked position . Frame Hook 4.
Maintenance and Support Support Cleaning For support and additional information about using your system, visit support.seesnake.com/compact-m40/. Clean your system with rags and a soft nylon brush. If desired, a mild detergent or disinfectant can be used. Do not use solvents or high pressure water to clean any part of the system. Maintaining Components Camera Head Scratches on the camera have a minimal effect on its performance. Do not use scraping tools or sand the camera to remove scratches.
Compact M40 – English – 13
– English – Compact M40
Compact M40 – English – 15
WWW.RIDGID.COM Ridge Tool Company 400 Clark Street Elyria, Ohio 44035-6001 USA 1-800-474-3443 Ridge Tool Europe NV (RIDGID) Ondernemerslaan 5428 3800 Sint-Truiden Belgium +32 (0)11 598 620 © 2019 Ridge Tool Company. All rights reserved. Every effort has been made to ensure that the information in this manual is accurate. Ridge Tool Company and its affiliates reserve the right to change the specifications of the hardware, software, or both as described in this manual without notice. Visit www. RIDGID.
