Instructions / Assembly

ManualsBrandsRiver of Goods ManualsCeiling FansHalston 52 in. Blue Tiffany Stained Glass LED Ceiling Fan With Light

MODEL NO.:

16160S

Installation Guide

MODEL NO.: 16160S

You may install your ceiling fan as Flush Mount, using the Short or Long Rod. Measure your room height

before installing the fan and consider the different installation height options indicated in the above diagram.

INSTALL THE BULBS IN THE MOTOR HOUSING before

hanging the ceiling fan

Required bulbs (not included):

Light kit-

use –

E12, Type B, 40W x 2 (Not Included)

Motor housing-

use

- E12, Type C, 7W x 4 (Not Included)

Alternative bulbs usage: CFL or LED Bulbs may be used. Ensure the Max. Wattage indicated on the socket

labels is not exceeded, and verify the bulbs do not get in contact with any metal part of the fan components

(shade or motor housing)

Table of Contents:

Safety tips Pg.2 Wiring Pg.7 -

Unpacking your fan Pg.3 Blade Assembly Pg.9

Tools and material required Pg.4 Canopy Assembly Pg.9

Outlet Box Pg.5 Light Kit and Shade Assembly Pg.10

Hanging Bracket Installation Pg.4 -

Troubleshooting Pg.11

Bulb installation Pg.6 Maintenance Pg.11

Fan Assembly Pg.6 -

7 Changing Bulbs Pg. 12

Professional Installation Recommended

Note: Approximate time of assembly is 30 min to 1 hour

PAGE 1

READ AND SAVE THESE

INSTRUCTIONS

Summary of content (12 pages)

PAGE 1
MODEL NO.: 16160S Installation Guide READ AND SAVE THESE INSTRUCTIONS MODEL NO.: 16160S You may install your ceiling fan as Flush Mount, using the Short or Long Rod. Measure your room height before installing the fan and consider the different installation height options indicated in the above diagram.
PAGE 2
MODEL NO.:QCF‐DB52061 SAFETY TIPS WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
PAGE 3
MODEL NO.:QCF‐DB52061 1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or styrofoam to avoid damage to finish. Do not discard fan carton or styrofoam inserts should this fan need to be returned for repairs. Check against parts inventory that all parts have been included. 2. Parts Inventory.
PAGE 4
MODEL NO.:QCF‐DB52061 3. Tools Required •Step ladder •Pliers •Screw driver flat head and phillip •Electrical tape •Circuit tester 4. Installation Preparation To prevent personal injury and damage, ensure that the hanging location allows the blade a clearance of 7ft.(2.13m) from the floor and 30in.(76cm) from any wall or obstruction. The fan is suitable for room sizes up to 400 square feet (37.2square meters). This fan can be mounted with a down rod on a normal or vaulted ceiling.
PAGE 5
MODEL NO.:QCF‐DB52061 CAUTION: Be sure outlet box is grounded properly and that a ground wire (green or bare) is present. Partially loosen screws in slotted holes of canopy. Remove the other 2 screws (along with the star washers) -save for later use. Twist canopy to remove hanging bracket. Install hanging bracket to outlet box using original screws, spring washers and flat washers provided with new or original outlet box.
PAGE 6
MODEL NO.:QCF‐DB52061 6. Bulbs Installation. Installing bulbs in the Motor Housing, locate the four access plates on the motor housing top. Remove two screws per access plate to reach each socket, use phillip screwdriver. Do not remove the Center Screw on each Access Plate Install each candelabra base Type C, 7W bulbs (Not Included). Reattach the Access Plates ensuring the screws are tightened enough to avoid vibrations during the fan operation.
PAGE 7
MODEL NO.:QCF‐DB52061 8. Fan Assembly with Down Rod - Choose the 4” or 21” Down Rod Remove Pin and Clip from down rod (if you have not already done so). Slide the Down rod through the canopy, and the Down rod cover as shown. Thread the electrical wires through down rod and pull extra wire slack from the upper end of the down rod. Tip: Apply small piece of electrical tape to the ends of the electrical wires to keep them together when threading them through the down rod. Loosen the Yoke set screw.
PAGE 8
MODEL NO.:QCF‐DB52061 3. Install the receiver into the Hanging bracket of the fan. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only. Do not install in damp locations or immerse in water. For indoor use only. Do not pull on or cut the receiver wire leads shorter. 4. Proceed making the wire connections following this diagram carefully. CAUTION: Incorrect wire connection would damage the receiver.
PAGE 9
MODEL NO.:QCF‐DB52061 Important: Make sure all electrical connections comply with Local Codes or Ordinances and the National Electrical Code. If you are unfamiliar with electrical wiring, or if the house/building wires are different colors than those referred to in the instructions, please use a qualified electrician. 10. Blade Assembly. Time Saver: Washers for blade screws can be set on each blade screw prior to installing blades.
PAGE 10
MODEL NO.:QCF‐DB52061 11. Light Kit Assembly. 1. Remove the three screws from the Light kit. 2. Plug the connectors from the Light kit to the connectors from the Switch housing. Please note the correct wiring is: •White to White • Blue to Blue 3.Gently push the connectors into switch housing and align the holes in the Light kit with holes in the Switch housing. Secure the light kit with the 3 screws that were previously removed.
PAGE 11
MODEL NO.:QCF‐DB52061 Ceiling Fan Troubleshooting Guide Welcome to the River of Goods family! We’re honored you’ve decided to include one of our ceiling fans in your home.
PAGE 12
MODEL NO.:QCF‐DB52061 Changing Bulbs (flush mount) Time to change your motor housing bulbs? No worries! Follow the steps below to guide you through the bulb changing process, all while keeping your ceiling fan mounted. 1. Locate the four (4) hex bolts on the bottom of the motor housing (circled below), and remove using either a wrench or socket wrench (5/16 or 8mm) 2. From the top of the motor housing, remove the four (4) shade holding bolts 3.