Specifications

Temperature Controller Driver
GP-Pro EX Device/PLC Connection Manual
239
continued to next page
Address Identifier Description Address Identifier Description
42 A1 Event 1 set value (EV1) 71 NR EDS action wait time (for disturbance 1)
43 A2 Event 2 set value (EV2) 72 NY EDS action wait time (for disturbance 2)
44 A3 Event 3 set value (EV3) 73 NT EDS value learning times
45 A4 Event 4 set value (EV4) 74 NU EDS start signal
46 A5 Control loop break alarm (LBA) time 75 EI Operation mode
47 N1 LBA deadband 76 ST Startup tuning (ST)
48 S1 Set value (SV) 77 Y8 Automatic temperature rise learning
49 P1 Proportional band [heat-side] 78 EF Communication switch for logic
4A I1 Integral time [heat-side] 79 XI Input type
4B D1 Derivative time [heat-side] 7A PU Display unit
4C CA Control response parameter 7B XU Decimal point position
4D P2 Proportional band [cool-side] 7C XV Input scale high
4E I2 Integral time [cool-side] 7D XW Input scale low
4F D2 Derivative time [cool-side] 7E AV Input error determination point (high)
50 V1 Overlap/Deadband 7F AW Input error determination point (low)
51 MR Manual reset 80 BS Burnout direction
52 HH Setting change rate limiter (up) 81 XH Square root extraction
53 HL Setting change rate limiter (down) 82 E0
Output assignment (Logic output selec-
tion function)
54 TM Area soak time 83 NA
Energized/De-energized (Logic output
selection function)
55 LP
Link area number 84 XA Event 1 type
56 A7 Heater break alarm (HBA) set value 85 FA Event 1 channel setting
57 NE
Heat break determination point 86 WA Event 1 hold action
58 NF Heater melting determination point 87 LF Event 1 interlock
59 PB PV bias 88 HA Event 1 differential gap
5A F1 PV digital filter 89 TD Event 1 delay timer
5B PR PV ratio 8A OA Force ON of Event 1 action
5C DP PV low input cut-off 8B XB Event 2 type
5D RB RS bias 8C FB Event 2 channel setting
5E F2 RS digital filter 8D WB Event 2 hold action
5F RR RS ratio 8E LG Event 2 interlock
60 DV Output distribution selection 8F HB Event 2 differential gap
61 DW Output distribution bias 90 TG Event 2 delay timer
62 DQ Output distribution ratio 91 OB Force ON of Event 2 action
63 T0 Proportional cycle time 92 XC Event 3 type
64 VI
Minimum ON/OFF time of proportioning
cycle
93 FC Event 3 channel setting
65 ON Manual manipulated output value 94 WC Event 3 hold action
66 RV Area soak time stop function 95 LH Event 3 interlock
67 NG EDS mode (for disturbance 1) 96 HC Event 3 differential gap
68 NX EDS mode (for disturbance 2) 97 TE Event 3 delay timer
69 NI EDS value 1 (for disturbance 1) 98 OC Force ON of Event 3 action
6A NJ EDS value 1 (for disturbance 2) 99 XD Event 4 type
6B NK EDS value 2 (for disturbance 1) 9A FD Event 4 channel setting
6C NM EDS value 2 (for disturbance 2) 9B WD Event 4 hold action
6D NN EDS transfer time (for disturbance 1) 9C LI Event 4 interlock
6E NO EDS transfer time (for disturbance 2) 9D HD Event 4 differential gap
6F NQ EDS action time (for disturbance 1) 9E TF Event 4 delay timer
70 NL EDS action time (for disturbance 2) 9F OD Force ON of Event 4 action