FS-99 2-Way Touch Screen Remote Paging Alarm & Engine Starting System OPERATION INSTRUCTIONS 1
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.
Remote function table Remote command Buttons Conditions Arm Disarm Lock Ignition on Unlock Ignition on Silent Arm Silent Disarm Car Finder Arm state Anti-Hijack Ignition on Panic Ignition off hold 2 sec Shock by pass Activate Channel 1 (Trunk Release) Activate Channel 2 (2nd Unlock) See function program hold 2 sec See function program then Activate Channel 3 (Dome Light) See function program Activate Channel 4 See function program Activate Channel 5 See function program Activate Cha
Outside view: MAIN PAGE: Press KEY to display Page 0: press anywhere in touch area to display PAGE ONE Press KEY hold 2 sec to display black& white pages Press the button for KEY it will become the main page press again it will become clock, and there are four colors for the clock, just touch these color point, the clock will change the color too.
Other PAGES: Button define is same as PAGE ONE,such as : P10K3 is CH5 button in p10 When transmitter received the car alarming will play trigger movies and sound voice: The move will be stopped,if the key pressed Cancel count down: Cancel alert time: set count down =00:00 set alert time =00:00 Button in other page function table: 5
Buttons Explain Buttons Explain Arm Set count down start time Disarm Compass Trunk Infrared remote control Remote engine start LOCATE/FIND Silent arm key Status Check Silent disarm key Get vehicle battery volt Activate Channel 3 Get the outside temperature Activate Channel 4 car jack key Activate Channel 5 Remote valet Activate Channel 6 Set currently car to 1st Engine running time add Set currently car to 2nd Silent Mode Set currently car to 3rd Open/close garage1 Set currently
can enter the setting page, to change the following settings date power save: ON/OFF time mode24H/12H Melody: ON/OFF language Key beep: ON/OFF set time Shock: ON/OFF back light power OFF N/Y light delay compass reset N/Y alert time Pin code switch ON/OFF alert switch ON/OFF Pin code change temperature unit ℃/℉ Press can switch option, press can switch on/off Infrared ray remote control instructions Can learn 4 different infrared ray remote control Learning method: 1. First choose item 2.
Touch-Screen Locate/Find function description z Locate/Find page: Press the button z to enter the Locate/Find page Select the transmitter: Press Locate/Find/Learning/Name register z button to select different transmitter which you want to Register the name for your selected transmitter: Press the name button to register each Locate/Find transmitter name For example: Select TAG1 to name the 1st transmitter.
If learning successful, the Touch-screen transmitter will display “OK” on the top-right side of the screen also a confirm melody. z Locate a. Press Then press the button button to select different transmitter which you want to Locate. to Locate Activate this function can locate where the missing key is. If there is a successful returned signal receiving from the lost transmitter, will display OK on the top-right side of the handset. If failed, will display LOST.
1. Arm button once, system will chirp once, parking lights flash once, lock the doors, starter disabled, Press window close output 30 sec. (if CH4 programmed), status LED start to flash slowly, Will chirp 4 times and parking lights flash 4 times if door or hood or trunk isn’t closed well while arming, and will not detect the door (hood, trunk) open until there are full closed well. • The pre-warn is bypassed after 5 cycles and reinstated after 10 minutes.
7. Arm without ZONE 1. Arm bypass sensor 1 Press button , once to set arming, siren chirp, parking lights flash once, Sensor 1 will be bypassed. Sensor 2 is normal 2. Arm bypass sensor2 , once to set arming, siren chirp, parking lights flash once, Press button Sensor 2 will be bypassed. Sensor 1 is normal 3. Arm bypass sensor1 and sensor2 Press button , once to set arming, siren chirp, parking lights flash once, Sensor 1 and Sensor 2 will be bypassed. 4.
7. Two-Stage unlock will unlock driver’s door only. Hold button Press button for 2 seconds or press button twice (see program feature 10), will unlock the passenger’s doors (activate “2nd stage Unlock Output”). If programmed. 8. Lock Press button will lock the doors. 9. Unlock When system is disarmed and ignition key is on, press button button will unlock the driver’s door. Hold will unlock the passenger’s doors (activate “2nd stage Unlock Output”). 10.
14. Channel 3 (Dome Light) to activate channel 3, remote Output pulse time of channel 3 is Press and release button programmable function (program feature 12). 15. Channel 4 (HORN -0/P) Press and release button to activate channel 4, remote Output pulse time of channel 4 is programmable function (program feature 13). 16. Channel 5 (ACC –O/P) Press and release button function (program feature 14). activate channel 5, remote Output pulse time of channel 5 is programmable 17.
20. Valet mode At valet mode system can be remote door lock / unlock, activate channels. No any protect function. Enter and exit Valet mode procedure: - Turn on ignition in disarm mode - Press override button 5 seconds - Parking lights flash and siren chirps 2 times Enter valet mode led still on. Exit valet mode led will off Other way: - In disarm mode - Press and release button 21. Override disarm - turn ignition ON - press override button 5 seconds. The system will disarms. 22.
24. Learn tachometer (RPM) - turn on ignition - press override button 6 times, - wait 2s, parking lights flash and siren chirps 6 times - press override button 1 times, - siren chirps one time Start the vehicle with the key. while the engine is running, the parking will flash. if don’t, please check tachometer wire connection. Press on transmitter to record the RPM. Chirp once to confirm. And exit the RPM learn mode. Press on transmitter to exit the RPM learn mode. chirp 4 times and flash 4 times 25.
26. Learning codes of remote transmitter There are only four transmitters may be learned in system’s memory. Codes of learned remote transmitters will be erased each time the learning mode is activated.
28. Programming functions 1. Turn Key to the ON position 2. Press program / valet button 5 times. After a few seconds the unit will flash the Parking lights and siren chirps 5 times 3. Push the valet program button [again] the number of times that corresponds to the option number desired (1-20X). You must get a light flash after each button press. See chart on next page for option list.
wire) 15 16 17 18 19 20 21 22 23 24 Channel 6 Ignition Run Latch On/Off Output (Ground when Latch On/Off with Ign Reset (Blue/black wire) Running) Disarm with OFF ON Trunk Pop 30 Sec. Park ON OFF Lights w/Disarm Pink Wire Selection Diesel *(-) Start *15 Sec. Delay (+) Glow Plug or Gasoline Activation* Start* Engine Maximum Crank 0.8 Seconds (-) 0.1 Seconds (+) 0.
