Quick Start Guide Owner's manual

ManualsBrandsRockwell Automation ManualsEquipment1336F PLUS II

PE PE

(L1)

(L2)

(L3)

(T1)

(T2)

(T3)

–

Dynamic Brake

Required

Input Fusing

Required Branch

Circuit Disconnect

Shield

Common Mode Core*

Diagram shows connections that are common for all drives.

Refer to User Manual for Detailed Information.

Ground per

Local Codes

Motor Frame

Motor

Terminator*

* Optional

Nearest

Building Structure Steel

AC Input

to Drive

Ground

Drive Output

to Motor

(Not on all drives) (Not on all drives)

Conduit/4-Wire Cable

BRK

–

Important: Verify motor insulation system peak voltage

rating. For cable lengths greater than 6.1

meters (20 feet), consult the User Manual.

Power Wiring – TB1

Digital Outputs – TB2

Only Present

on B Frame

& Up Drives

Reserved for

Future Use

CR2

CR1 CR3CR3 CR4CR4

11 12 13 14 15 16 17 18 A1 A2

Terminal

10, 11

11, 12

13, 14

14, 15

16, 17

17, 18

A1, A2

Signal

True Earth - Shield Termination

CR1 Programmable Contact

CR2 Programmable Contact

CR3 Programmable Contact

CR4 Programmable Contact

Reserved for Future Use

Resistive Rating = 115V AC/30V DC, 5.0A

Inductive Rating = 115V AC/30V DC, 2.0A

Contacts Shown in Unpowered State

(or Powered State with Fault/Alarm Present)

Important: On A Frame Drives, the power supply used for relay contact outputs requires a field installation of

transient voltage surge suppression with maximum clamping voltage of 2.5 kV on all control boards.

1336 PLUS II Quick Start Guide

This Quick Start Guide summarizes the basic steps needed to install, start-up and program the 1336 PLUS II Adjustable

Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualif

ied drive service

personnel

only. Refer to the 1336

PLUS II User Manual (publication 1336 PLUS-5.3) for details on other application

considerations and related precautions.

Publication 1336 PLUS-5.9ML – June, 2003 P/N 188747 (06)

Summary of content (6 pages)

PAGE 1
336 PLUS II Quick Start Guide This Quick Start Guide summarizes the basic steps needed to install, start-up and program the 1336 PLUS II Adjustable Frequency AC Drive. The information provided Does Not replace the User Manual and is intended for qualified drive service personnel only. Refer to the 1336 PLUS II User Manual (publication 1336 PLUS-5.3) for details on other application considerations and related precautions.
PAGE 2
1336 PLUS II Quick Start Guide Digital Inputs – TB3 A hazard of personal injury from automatic restart exists with 2-wire control. 2-wire control uses maintained Run contacts that act as both Run (closed) and Stop (open) devices. Opening the Stop contact (terminal 20) will stop the drive. If this contact is reclosed, any fault will be reset. If a valid Start command is still present, the drive will restart. Only use 2-wire control for applications outlined in NFPA79, "Under Voltage Protection.
PAGE 3
Analog I/O – TB2 Only Present on B Frame & Up Drives TE Signal Common TE 1 2 3 4 Std. Pot. Reference +5V 1, 3 Single-Ended Single-Ended Signal Input 0 Input 1 Common Pot., 10V or 20mA Pot.
PAGE 4
1336 PLUS II Quick Start Guide ❑ 5. If Analog Option is installed, verify that DIP switch(es) are properly set (refer to Option Instruction Sheet). ATTENTION: In all of the following steps, rotation of the motor may occur. To guard against injury, incorrect rotation and possible equipment damage, read each step carefully and perform with caution. ! ❑ 6. Apply AC power and control voltages to the drive, the LCD display should light and display a drive status of “Stopped” and an output frequency of “+0.
PAGE 5
1336 PLUS II Quick Start Guide OPERATOR LEVEL Power-Up Mode & Status Display ESC or SEL or or or MODE LEVEL Not Available on Series A HIMs (below Version 3.
PAGE 6
Not Available on Series A HIMs (below Version 3.0) Not Available on Series A HIMs (below Version 3.0) Read Only Save Values 2 Recall Values 2 Control Logic Fault Queue Reset Defaults HIM -> Drive 1 Drive -> HIM 1 to Linear List & Metering Ratings Masks Owners Adapter I/O Rated Volts (147) Rated Amps (170) Rated kW (171) Firmware Ver.