/Operating System Upgrade Owner's manual

ManualsBrandsRockwell Automation ManualsEquipment1747-OS302_OS401 SLC 5/03 and 5/04 Processors Firmware

1 Publication 1747-IN007C-EN-P - October 2002

Installation Instructions

SLC 5/03™ and SLC 5/04™ Processors

Firmware/Operating System Upgrade

Introduction

Enclosed in this package is a firmware/operating system upgrade for

your SLC 5/03 or SLC 5/04 processor. Take anti-static precautions

when upgrading the firmware.

If you upgrade an SLC 5/03 or SLC 5/04 processor, you receive

anomaly fixes as well as added functionality. During the upgrade, the

ladder logic program inside the processor is erased. Therefore, the

first step in upgrading the firmware/operating system is to save the

processor’s ladder logic program.

This product is CE compliant for all applicable directives when

product or packaging is marked.

Installation Procedure

Follow these instructions carefully. Refer to page 3 for component

placement information.

1. Save the current user program to your hard drive using your

programming software, to a memory module, or to a 1747-PSD

Program Storage Device.

2. Remove the communication cable between the processor and

your programming terminal.

ATTENTION

The Flash EPROMs are electrostatic sensitive devices.

Do not handle without proper grounding

precautions. Do not install PROM with power

applied to the SLC 5/03 or SLC 5/04 processor.

IMPORTANT

The user program is cleared as part of the

firmware/operating system upgrade process.

You must restore your program after loading

the upgrade. Also, all communication ports are

returned to the default parameters.

Summary of content (8 pages)

PAGE 1
Installation Instructions SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade Introduction Enclosed in this package is a firmware/operating system upgrade for your SLC 5/03 or SLC 5/04 processor. Take anti-static precautions when upgrading the firmware. ATTENTION ! The Flash EPROMs are electrostatic sensitive devices. Do not handle without proper grounding precautions. Do not install PROM with power applied to the SLC 5/03 or SLC 5/04 processor.
PAGE 2
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade 3. Remove power from the chassis containing the processor. ATTENTION ! Do not remove the processor from the SLC 500 chassis until all power is removed from the SLC 500 power supply. 4. Remove the processor from the chassis. 5. Plug the firmware/operating system upgrade pack into the memory module socket. 6. Move the operating system write-protect jumper (J4) to the unprotected, or program, position.
PAGE 3
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade 3 Figure 1 Component Placement Information Catalog and Serial Number Label Place the firmware upgrade label here. SLC 500 PLACE FRN UPGRADE LABEL HERE PROCESSOR UNIT OPERATING SYSTEM INFO SER FAC OS # CAT SER FRN CURRENT REQUIREMENTS: PROTECT WHITE RED SERIAL NO. PROC. REV.
PAGE 4
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade 12. Move the operating system write-protect jumper (J4) back to the protected position (see diagram on page 3). IMPORTANT Failure to return the J4 jumper to the protected position results in an error (0x3D Hex) on the power cycle following the download of a valid program to the processor. This error condition prevents the module from going to run and causes Channel 0 communication settings to return to their defaults.
PAGE 5
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade 5 If the LED’s indicate:(1) POWER The Following Error Exists Probable Cause Recommended Action RUN FORCE FLT DH485 BATT RS232 Fatal Hardware Error Major hardware failure due to noise, improper grounding, or poor power source. Cycle power and see if the error repeats itself. If the error clears, you should be able to download the firmware. If the error persists, contact your Rockwell Automation representative.
PAGE 6
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade If the LED’s indicate:(1) POWER RUN FORCE FLT DH485 BATT RS232 The Following Error Exists Probable Cause Recommended Action Downloadable Operating System Failure Failure during transmission of downloadable operating system. Download the operating system.
PAGE 7
SLC 5/03™ and SLC 5/04™ Processors Firmware/Operating System Upgrade 7 If the LED’s indicate:(1) POWER RUN FORCE FLT DH485 BATT RS232 The Following Error Exists Probable Cause Recommended Action NVRAM error Major hardware failure due to noise, improper grounding, or poor power source. Cycle power and see if the error repeats itself. If the error clears, you should be able to download the firmware. If the error persists, contact your Rockwell Automation representative.
PAGE 8
Rockwell Automation Support Rockwell Automation provides technical information on the Web to assist you in using its products. At http://support.rockwellautomation.com, you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools.