Installation and Programming Manual ProSYS version 7.
Installation and Programming Manual ProSYS version 7.
CE Declaration of Conformity Hereby, RISCO Group declares that this control panel (ProSYS 128, ProSYS 40, ProSYS 16), with wired accessories (including cables) and wireless accessories, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.
Table of Contents CHAPTER 1: INTRODUCING PROSYS......................................................................................... 1-1 WHAT IS PROSYS?........................................................................................................................ 1-1 INSTALLING PROSYS ..................................................................................................................... 1-2 ABOUT WIRE ................................................................................
Wiring Additional Modules ....................................................................................................... 3-7 STEP 5: APPLYING POWER.............................................................................................................. 3-7 CHAPTER 4: PROGRAMMING THE PROSYS.............................................................................. 4-1 USING THE PROSYS MAIN PANEL PROGRAMMING OPTIONS ..............................................................
Dialer: Alarm Restore............................................................................................................. 5-83 Dialer: Periodic Test............................................................................................................... 5-84 Dialer: More ........................................................................................................................... 5-85 REPORT CODES ...................................................................................
vi ProSYS Installation and Programming Manual
Chapter 1: Introducing ProSYS This chapter provides a basic introduction to the ProSYS system and its architecture and capabilities, as described in the following sections: ♦ What is ProSYS?, below ♦ Installing ProSYS, page 1-2 ♦ About Wire, page 1-2 ♦ ProSYS Architecture and Capabilities, page 1-5 ♦ ProSYS Features, page 1-6 What is ProSYS? ProSYS is an integrated security system with unrivalled flexibility and advanced expansion capabilities, together with being simple to install, program and maintain.
Installing ProSYS This ProSYS Installation and Programming Manual details how to install the ProSYS hardware and to program the ProSYS Main Panel, as described in the following main steps: ♦ Step 1: Mounting the Main Panel (Chapter 2) ♦ Step 2: Wiring the Main Panel (Chapter 2) ♦ Step 3: Identifying and Wiring Keypads and Expansion Modules (Chapter 3) ♦ Step 4: Adding Modules (Chapter 3) ♦ Step 5: Applying Power (Chapter 3) ♦ Step 6: Programming the ProSYS (Chapters 4 and 5) ♦ Step 7: Programming within th
AWG Gauge Size Inches Millimeters Ω Per Foot Ω Per 1000 Feet Ω Per Meter Ω Per 100 Meters 24 0.020 0.50 0.026 26.0 0.085 8.5 22 0.025 0.64 0.016 16.0 0.052 5.2 20 0.031 0.80 0.010 10.0 0.032 3.2 19 0.035 0.90 0.008 8.0 0.026 2.6 18 0.040 1.00 0.006 6.0 0.020 2.0 16 0.050 1.27 0.004 4.0 0.013 1.3 14 0.064 1.63 0.0025 2.5 0.008 0.
Total Auxiliary Power (Max Current Draw per Branch) Desired Wire Gauge in Particular Branch 32/02 mm 18 AWG 28/02 mm 19 AWG 24/02 mm 20 AWG 16/02 mm 22 AWG 7/02 mm 24 AWG Max Run Max Run Max Run Max Run Max Run Meters Feet Meters Feet Meters Feet Meters Feet Meters Feet 20mA 1195 3920 945 3100 750 2460 472 1550 296 970 30mA 793 2600 628 2060 500 1640 314 1030 197 646 40mA 597 1960 472 1550 375 1230 236 775 148 485 50mA 478 1568 378 1240 300 984 18
ProSYS Architecture and Capabilities The following diagram provides an overview of the ProSYS's architecture and capabilities. Examine this figure before beginning your ProSYS installation to obtain an overall picture of the full extent of the ProSYS system's capabilities.
ProSYS Features This section describes the features of the ProSYS system, including features specific to each ProSYS model.
Main Panel The Main Panel is the foundation of the system's operation and has the following features: ♦ 8 basic hardwired zones ♦ 6 Utility Outputs: 1 x relay (programmable output) (3 Amps) 1 x 500mA transistor (Open Collector) 4 x 70mA transistors (Open Collector) ♦ Box tamper input (normally open) ♦ Bell tamper input (using a 2.2KΩ end-of-line resistor) ♦ Two different 4-wire BUSes with "quick connectors" from the Main Panel, which is the initial point for all system.
The Wireless expansion module includes the following features: ♦ Super heterodyne technology ♦ Programmable supervision time ♦ Tamper detection ♦ Low battery in transmitters detection ♦ Signal jamming indication ♦ Programmable supervision time Partitions/Areas ♦ ♦ ♦ ♦ Up to 8 independent partitions/areas Any zone can be assigned to any partition/area Each partition/area supports both zone sharing and cross zoning.
User Codes and Authority Levels ♦ ♦ ♦ ♦ ♦ ♦ ♦ 1 engineer code 1 sub engineer code 1 Grand Master code Up to 99 user codes (ProSYS 128) 8 Authority levels Double code option for high security Codes can be defined to 4 or 6 digits (By default 6 digits) Programmable Utility Outputs ♦ ♦ ♦ ♦ ♦ Supports additional 16 (ProSYS 16), 32 (ProSYS 40) or 64 (ProSYS 128) outputs 4-relay or 8-transistor expansion output modules Outputs operation follows system events, codes or scheduling programs.
Advanced Digital Voice Module The Advanced Digital Voice module provides audible information about the status of your ProSYS system and enables any remote, touch-tone (DTMF) telephone to act as a keypad for the system. The Advanced Digital Voice Module can be used in the following situations: ♦ Upon event occurrence, such as alarm activation, the Advanced Digital Voice module informs you of a security situation, such as intrusion or fire, by calling you and playing a pre-recorded Event announcement.
Event Logging The ProSYS has the capability of storing up to 999 significant events, including arming, disarming, bypassing, alarms, troubles, restorals, and resets. These events are logged in order according to date and time, and when applicable, according to Zone, Partition, Area, User Code, Keypad, etc. When appropriate, such events can be displayed on an LCD keypad or uploaded to the MS via the Upload/Download software and printed for further analysis.
1-12 ProSYS Installation and Programming Manual
Chapter 2: Mounting and Wiring the Main Panel This chapter covers the first two steps of the ProSYS installation procedure, as follows: ♦ Step 1: Mounting the Main Panel, below ♦ Step 2: Wiring the Main Panel, page 2-3 Step 1: Mounting the Main Panel The ProSYS Main Panel . should be installed inside a metal box Attach the box to the wall using the proper hardware, as shown below. Figure 2-1: Mounting the Main Panel The mounting location should be: ♦ Dry. ♦ Near an AC power supply (switched off).
Safety Precautions When mounting the Main Panel, the following safety precautions are relevant: ♦ When the Main Panel is powered on, mains voltage is present on the main PCB. To prevent risk of electric shock, disconnect all power (AC transformer and battery) and phone cords before servicing. Under no circumstances should mains power be connected to the PCB other than to the main terminal block.
Step 2: Wiring the Main Panel This step explains the various wiring and connection procedures that must be performed when wiring the Main Panel, as follows: ♦ Wiring the Main Panel, page 2-3 ♦ Wiring the Zones to Sensors and Detectors (Zone Terminals Z1 through Z8), page 2-4 ♦ Wiring the Auxiliary Devices, page 2-6 ♦ Wiring the Bell Sounders, page 2-7 ♦ Wiring the Bell Tamper, page 2-7 ♦ Wiring the Box Tamper, page 2-8 ♦ Wiring External Triggerable Devices, page 2-8 ♦ Connecting the J10 Connector, page 2-9
The second set of four terminals on the left of the Main Panel represent the Expansion BUS. These support the connection of keypads and expansion modules.
NOTES: It is recommended that you use an End-of-Line Resistor at the far end of each hardwired zone to prevent short-circuits (16 resistors are supplied). For a zone with a tamper switch, you can use a Double End-of-Line Resistor to save additional Main Panel connections (refer to Figure 2-4 on page 2-6). 3. Terminate unused zones at the Main Panel. 4. Connect the power to the sensors and/or detectors, as described in Wiring the Auxiliary Devices, page 2-6.
Connections on Zone Expanders (ProSYS EZ8, ProSYS EZ16): Figure 2-4: Zone Connection Diagrams Wiring the Auxiliary Devices ¾ To wire auxiliary devices: ♦ Use the Auxiliary Power AUX (+) COM (-) terminals to power PIRs, glass-break detectors (4-wire types), smoke detectors, audio switches, photoelectric systems and/or any device that requires a 12V DC power supply. NOTES: The total power from the AUX terminals should not exceed 600mA.
Wiring the Bell Sounders ¾ To wire the bell sounders: 1. Connect a suitable wire to the internal sounding device(s) inside the building (bell, electronic siren, or loudspeaker). 2. Ensure that you note the polarity when connecting electronic siren(s) and/or polarized bells. ! WARNING: To avoid Bell Loop Trouble, if NO connection is made to an internal sounder, use a 2200Ω resistor in its place. NOTE: It is important to position the BELL/LS Jumper (J3) correctly.
Wiring the Box Tamper ¾ To wire the box tamper: ♦ Connect the box tamper to the BOX TMP and COM terminals on the Main Panel, as illustrated in Figure 2-2 on page 2-3. Refer also to the diagram shown below. Figure 2-5: Wiring the Box Tamper Wiring External Triggerable Devices ¾ 2-8 To wire external triggerable devices: ♦ Wire the external triggerable devices that you want to activate to the outputs UO1-UO6, as follows: UO1: Refer to the J10 connector instructions, described in the next section.
Connecting the J10 Connector POS NEG Figure 2-6: Connecting the J10 Connector The J10 connector (jumper) determines the UO1 connection (behavior), which is normally used for an external siren connection, as follows: ♦ Positive (POS): When the J10 connector is placed on POS, the C terminal on UO1 receives 13.8V. NOTE: The maximum current for UO1 and the bell should not exceed 900mA. ♦ Negative (NEG): When the J10 connector is placed on NEG, the C terminal on UO1 receives COM.
Connecting to Ground (Earth) ¾ To connect to ground (earth): ♦ Connect the metal box and the door of the metal box to mains earth (ground), as shown in the diagrams on the following page. Refer also to What Makes a Good Ground?, page 2-2. ! IMPORTANT: Connecting to ground must be performed according to the local National Electrical Code. Figure 2-7: Grounding the Metal Box Figure 2-8: Grounding the Metal Box Door Connecting Telephone Lines These lines are typically derived from an installed RJ31X jack.
Jumper Settings The ProSYS is equipped with internal jumpers. Use the following table to configure the jumpers according to the desired configuration. Jumpers Position Enables to default the panel and restore the ProSYS codes (Grand master, installer and sub installer) to the manufacturers default settings.
Connectors Connector Function J1, J5 BUS 1 Plug in connector. J8 BUS 2 Plug in connector. J4 SIG In connector. The J4 SIG IN voice connector enables the transfer of audio data between the Voice module RP200VC and the phone line. The J6 connector is used to connect the Advanced Digital Voice Module (rp128ev00uka) to the ProSYS. Connect the Voice module to the VOICE connector (J6) on the Main Panel via the supplied cable.
Chapter 3: Installing External Modules and Devices This chapter describes steps 3 to 5 of the ProSYS installation procedure, as follows: ♦ Step 3: Identifying and Wiring Keypads and Expansion Modules ♦ Step 4: Adding Modules, page 3-3 ♦ Step 5: Applying Power, page 3-7 Step 3: Identifying and Wiring Keypads and Expansion Modules This section explains how to program a unique ID number to identify each keypad and expansion module in the system and how to install a keypad, as follows: ♦ Programming Device ID
Installing a Keypad NOTE: For information on installing the Touchscreen keypad, refer to the ProSYS Touchscreen Keypad Instruction manual that is included with the product. ¾ To install a keypad: 1. Open the Keypad Cover: Remove the back of the keypad cover, and using a screwdriver, press in each of the retaining clips to separate the back cover from the keypad. Take care not to touch the circuitry of the keypad buttons. 2.
4. Set the Tamper Switch: Before mounting the keypad on the wall, locate the rear-mounted Tamper Switch and make sure that it is vertically oriented. 5. Replace the Cover: Carefully replace the keypad's printed circuit board in its cover. Join the cover and base by hooking the tops together and then snapping the bottom in place, returning the retaining clips to their positions.
Wiring Utility Output Modules Figure 3-5: Utility Output Module UO4 (Showing an Example of UO4 Wiring) Figure 3-6: Utility Output Module E08 ¾ Figure 3-7: Utility Output Module X-10 To wire Utility Output modules: 1. Set the Dip Switches: Assign a unique ID to each Utility Output expansion module by setting the dip switches, using Figure 3-1 on page 3-1. NOTE: The ID for the first Utility Output expansion module is 01, for the second 02, and so on.
3. Set the Tamper (TAMP COM): The Utility Output expansion module can be contained in a metal cabinet. Tamper the cabinet, as follows: Connect one (or more) normally open (NO) momentary-action pushbutton switches in a series between the TAMP and COM terminals in order to short-circuit these terminals while the cabinet door is closed. NOTES: It is not necessary to use a tamper switch if another module sharing the same cabinet is equipped with one.
Wiring Power Supply Expansion Modules OU OU 1 N.C N.O C N.C 2 C N.O (PS LED) (UO LED) PS ON BAT (Battery Jumper) Battery 1 2 3 4 1 2 3 4 OC (Over Current LED) BELL/LS (Bell/Loudspeaker Jumper) Connections LS ON ON 1 2 3 4 BELL OFF SW1 BUS COM TAMP BLK YEL GRN + BELL LS AUX RED AC BUS Loudspeaker/ Bell Transformer Power to Accessories and Detectors Figure 3-8: 1.5A Power Supply Module PS ¾ Figure 3-9: 3A Power Supply Module PS To wire Power Supply expansion modules: 1.
If a tamper switch is not used, connect a wire jumper between the two terminals. 4. Connect the Internal Siren BELL/LS (+) (-): Connect a suitable wire to the internal device(s) to be driven by the Power Supply expansion module (bell, electronic siren, or loudspeaker). Use a larger wire gauge if the distance separating the siren and the module is significant.
3-8 ProSYS Installation and Programming Manual
Chapter 4: Programming the ProSYS This chapter explains the ProSYS programming options, how to use the keypad elements, and the basics about programming via the keypad, as described in the following sections: ♦ Using the ProSYS Main Panel Programming Options, below ♦ Using the LCD Keypad, page 4-2 ♦ Programming from the LCD Keypad, page 4-4 ♦ Using the Program Transfer Module, page 4-9 For detailed information about each Programming option, refer to Chapter 5, Using the Installer Programming Menus.
Using the LCD Keypad ? #/ Figure 4-1: The LCD Keypad Face The LCD keypad is a visual interface tool that helps you operate the ProSYS Main Panel. The LCD keypad contains six LED indicators and a variety of keys. Their typical uses are described in the following table: NOTE: For information regarding the TouchScreen keypad please refer to the instructions supplied with the product.
Item Key/LED Programming Mode/Function 7 A, B, C, and D Use these keys for defining groups and macros. Refer to the Groups section in Chapter 1, Introducing ProSYS for further details. 8 Use this key to exit the current programming selection and move up to the next higher level in the programming hierarchy. 9 LCD Program Display The LCD program display consists of two lines.
Programming from the LCD Keypad This section explains how to use the keypad to access the Installer Programming menu as well as how to restore the manufacturer's defaults, as described in the following sections: ♦ Accessing the Installer Programming Menu, below ♦ Restoring Manufacturer's Programming Defaults, page 4-6 ♦ Keypad Timeout, page 4-8 ♦ Using the Program Transfer Module (PTM), page 4-9 Accessing the Installer Programming Menu This section describes how to access the Installer Programming menu for
NOTE: Refer to Accessories: Auto Settings section of Chapter 5, Using the Installer Programming Menus for further details. The Power/ LED begins flashing slowly at this point, indicating that you have entered a programming session. ¾ To access the Installer Programming Menu from the regular operation mode: 1. When you power up the system, the following display appears: PLEASE WAIT… After a brief wait, the keypad displays the regular operation mode, as follows: 2. Press .
The main Installer Programming menu options are available, as follows: [1] SYSTEM [2] ZONES [3] UTIL OUTPUT [4] CODE MAINT [5] DIALER [6] REPORT CODES [7] ACCESSORIES [8] MISCELLANEOUS [9] ACCESS CONTROL [0] EXIT PROGRAM Each of the main Installer Programming menu options enables you to access and program all of the ProSYS options. Refer to Appendix E, Installer Programming Maps for a complete list of all the programming options.
and then press [0]. The keypad prompts you to save the changes by 5. Press displaying the following message: 6. Confirm saving the data by pressing the the keypad displays the following messages: / key. A short beep will sound, and 7. Next, the system will perform a Tamper Test. The following display appears: TESTING: PLEASE WAIT If a tamper occurs in the system (Bell, box or other) the display will show a list of the tamper faults in the system.
¾ To 1. 2. 3. 4. restore the Main Panel to the manufacturer's defaults: Disconnect all power from the Main Panel. Remove the J2 default jumper from its position on one of the J2 pins. Position the J2 default jumper on both of the J2 pins. Reconnect the power to the mains and backup battery to the Main Panel. The keypad sounds a long beep and all of the LEDs flash once. The following message is displayed on the keypad for 20 seconds: And then the following message is displayed: 5.
Using the Program Transfer Module (PTM) The Program Transfer Module (PTM) is used to create and apply standard programming templates. In addition, you can use the PTM on powered-up, properly functioning Main Panels, which have been previously programmed. ¾ To create a Programming Template by copying from a programmed Main Panel: ♦ Use a programmed Main Panel to create a Programming Template to be applied to other Main Panels. The programming on the Main Panel is ready for copying.
When the LED stops flashing rapidly, the keypad beeps once, and its display returns to the normal initial display. 6. Remove the PTM from the BUS connector and remove the J2 jumper plug. 7. Position the J2 jumper plug on one of the pins of the J2 connector. 8. From an LCD keypad, access the main Installer Programming menu by pressing [7] [1]. The first option of the main Installer Programming menu is displayed. 9. Without making any changes, exit the main Installer Programming menu by pressing [0].
Chapter 5: Using the Installer Programming Menus This chapter describes the ProSYS programming options and functions, as well as all quick key shortcuts.
NOTE: When programming items in sequence, you can use the / 1 key to exit to the previous level and the key to toggle the options. System The System menu provides access to submenus and their related parameters that are used for programming configuration settings applicable to the entire system.
System: Time Define Quick Keys 1 1 Parameter Default Range 30 seconds 0-255 seconds Exit/Entry Delay 1 1 Exit/Entry Delays (Group 1). 1 1 1 1 Entry Delay 1 Duration of Group 1 Entry Delay. Note: For SIA CP 01 installations the range of entry time should be between 30 to 240 seconds with default of 30 seconds. 1 1 1 2 Exit Delay 1 45 seconds 0-255 seconds Duration of Group 1 Exit Delay.
System: Time Define Quick Keys 1 1 1 1 6 6 Parameter Default Range 1 Jamming Time NONE NONE, 10, 20 or 30 seconds 2 Specifies the period of time that the ProSYS's wireless module tolerates unwanted radio frequencies capable of blocking (jamming) signals produced by the system's transmitters. Once the specified time is reached, the Main Panel sends a Report Code to the Monitoring Station (MS). (Refer to Jamming Trouble, page 5-102.) NONE: No jamming will be detected or reported.
System: Time Define Quick Keys 1 1 9 2 Parameter Default Range Guard Delay MIN: 30 01-99 minutes Specifies the time period that the system will be disarmed after an authorized user enters a Guard code. 1 2 System: System Control The System Control menu contains parameters that control specific system operations. ¾ To access the System Control menu: 1. Access the System menu, as described on page 5-2. 2. From the System menu, press [2] to access the System Control menu options.
System: System Control Quick Keys 1 2 06 Parameter Default Range Bell Squawk YES YES/NO YES: If a keyswitch or a rolling code remote control is used, a brief "chirp" is produced from the system's external sounder(s) (at the conclusion of the Exit Delay period), as follows: ♦ One chirp indicates the system is armed. (Also from keypad) ♦ Two chirps indicate the system is disarmed. ♦ Four chirps indicate the system is disarmed after an alarm. NO: No "chirp" is produced.
System: System Control Quick Keys 1 2 13 Parameter Default Range Alarm ZE Cut NO YES/NO YES: Produces an alarm if the communication between the Main Panel and any expander is lost. A report is transmitted to the MS. NO: No alarm occurs. The system, however, produces a local trouble indication. 1 2 14 Fire Temporal Pattern NO YES/NO YES: During a fire alarm, the external sounders produce a pattern of three short bursts, followed by a brief pause.
System: System Control Quick Keys 1 2 20 Parameter Default Range Summer/Winter Clock NO YES/NO YES: The ProSYS automatically sets its Time of Day clock one hour ahead in the spring (on the last Sunday in March) and one hour back in the Autumn (on the last Sunday in October). NO: No automatic time accommodation is made. 1 2 21 Forced Keyswitch Arming YES YES/NO YES: Keyswitch or Proximity Key arming is performed on any partition.
System: System Control Quick Keys 1 2 23 Parameter Default Range Arm Pre-Warning YES YES/NO Related to auto arm/disarm operation. YES: For any partition(s) set up for Auto Arming, an audible Exit Delay (warning) countdown will commence 4.25 minutes prior to the automatic arming. (Refer to the user's Daily Arm function in the ProSYS User's Manual for additional details.) During this period, Exit Delay beeps will be heard in the keypads assigned to these partitions.
System: System Control Quick Keys 1 2 28 Parameter Default Range IMQ Install NO YES/NO YES: Causes the following parameters to function as follows: 1 2 29 ♦ Auto Arm Bypass: If there is an open zone during the Auto Arm process, the system will be armed, and an alarm will be sounded (unless the open zone is closed). ♦ Guard User: If a Guard user disarms a partition, the system will be armed automatically after the predefined time period (refer to Guard, page 5-5).
System: System Control Quick Keys 1 2 32 Parameter Default Range Global Follower YES YES/NO YES: Specifies that all zones (that are programmed to follow an Exit/Entry Delay time) will follow the Exit/Entry Delay time of any armed partition. NO: Specifies that all zones (that are programmed to follow an Entry Delay time) will follow the Entry Delay time of only the partitions to which they are assigned.
System: System Control Quick Keys 1 2 38 Parameter Default Range Siren Auxiliary = Tamper NO YES/NO This parameter relates to the BUS siren. YES: A siren auxiliary trouble will be regarded as tamper alarm by the system. NO: A siren auxiliary trouble will be regarded as trouble by the system. 1 2 39 GSM Pre Alarm Indication NO YES/NO Related to the GSM/GPRS module. This parameter specifies if the ProSYS will send a pre alarm message to the GSM when an entry delay starts.
1 4 System: Windowing The Windowing menu enables you to define a time window and its effective days for Reporting of Opening/Closing signals when the system is either disarmed or armed outside of the specified time window. ¾ To access the Windowing menu: 1. Access the System menu, as described on page 5-2. 2. From the System menu, press [4] to access the Windowing menu options. The following display appears: 3.
NOTE: The data sequence of each key in the following table is suitable only for the English version. KEY DATA SEQUENCE 1 1 A B C D E F G H I J K L M 2 2 N O P Q R S T U V W X Y Z 3 3 ! '' & ' : – . ? / ( ) 4 4 a b c d e f g h i j K l m 5 n o p q r s t u v w X y z 5 6-0 Each of these keys toggles between producing their number and a blank space. / Use this button to toggle forward through the available characters.
System: System Labels Quick Keys 1 5 1 to 8 Parameter Default Range Partitions 1 through 8 Partitions 1 through 8 Any 12 characters Partitions 1 through 8. Example: The example below describes how to edit each partition label. TO ASSIGN THE JONES'S NAME TO PARTITION 1, FOLLOW THE STEPS BELOW: 1. Press [1] for partition 1 and press / . 2. Press the [2] key repeatedly until a T appears in the display; press the key once to move the cursor to the right. / 3.
System: Tamper Sound Quick Keys Parameter Default Range NOTE: If you select the last option (5), during a Tamper alarm, a bell will sound when the system is armed, and a buzzer will sound when the system is disarmed. 1 7 System: Default Enable/Disable Default: Enable Range: Enable/Disable The Default Enable/Disable menu contains parameters that relate to what happens if the Main Panel's DEFAULT (J2) Jumper is in place when power to the Main Panel is switched off and then on.
System: Service Information Quick Keys 1 8 2 Parameter Default Service Phone Range Any 16 characters Enables you to insert and/or edit the service phone number. 1 9 System: System Version The System Version menu supplies the current system version information. ¾ To access the System Version menu: 1. Access the System menu, as described on page 5-2. 2. From the System menu, press [9] to access the System Version menu option. The system version with the software's checksum number is displayed.
2 Zones The Zones menu provides access to submenus and their related parameters that are used for programming the characteristics of each of the system's protected zones. You can program by zone or by category. The first submenu allows you to program all parameters for each zone one by one. You can also program one or more zones by category using the following sub-menus: Partitions/Groups, Zone Type, Zone Sound, Termination, Loop Response, Cross Zone, and Labels.
The following procedure describes how to program the full complement of parameters for each zone on a one-by-one basis. ¾ To access the One by One menu: 1. Access the Zones menu, as described on page 5-18. 2. From the Zones menu, press [1] to access the One by One menu options. The following display appears: NOTES: In the mm:zz designation, the mm = the module ID number, and the zz = the zone number for this module (the number next to the terminal block on the expander).
♦ To program one or more of the system's zones using the One by One method, changes made to any (or all) of the Zone parameters will NOT be recorded without going through the One by One list, ending with the Zone Labels parameter of the last zone you want to program. ♦ After making changes to the Zone Labels parameter, press . This / produces a one-second tone and assures that change(s) you make to the zone programming are recorded when you exit the One by One programming mode.
2 3 Zones: Zone Type The Zone Type menu contains parameters that enable you to program the zone type for any zone. Setting the zone type is partly determined by the arming levels. Three arming levels exist, as follows: ♦ Disarm: The system reacts only to those zones defined as 24 HR, Fire, Panic, and Trouble. ♦ Arm: The system reacts to all zones. ♦ Stay: The system does not react to zones defined as internal (home). This setting allows freedom of movement in those zones.
Zones: Zone Type Quick Keys 2 3 ZZ + / Parameter Default Arming Level/Range Exit (OP)/Entry Default for zone 1 ARM/STAY 03 Used for an exit/entry door, open during the armed period. This zone behaves as described in the Exit/Entry 1 parameter, shown above, except that, if faulted when the system is being armed, it does NOT prevent arming. To avoid an intrusion alarm, it must be secured before the expiration of the Exit Delay period.
Zones: Zone Type Quick Keys 2 3 Parameter ZZ + 08 / Default I+Exit(OP)/Entry (Interior+Exit(OP)/Entry) Arming Level/Range Arm Used for an exit/entry door that, for convenience, may be kept open when the system is being armed, as follows: ♦ In AWAY (ARMED) mode, refer to the explanation in Zone Type 03, page 5-22. ♦ In STAY (ARMED) mode, the zone will be bypassed.
Zones: Zone Type Quick Keys 2 3 Parameter Default 24 Hours ZZ + Arming Level/Range All 13 / Usually assigned to protect non-movable glass, fixed skylights, and cabinets (possibly) for shock detection systems. A violation of such a zone causes an instant intrusion alarm, regardless of the system's state. 2 3 Fire ZZ + / All 14 For smoke or other types of fire detectors.
Zones: Zone Type Quick Keys 2 3 Parameter Default Arming Level/Range Latch Keyswitch ZZ + 19 / Connect an external SPST latched (non-momentary) keyswitch to any zone terminals given this designation and operate the keyswitch, as follows: ♦ After arming one or more partitions using the keyswitch and then disarming using the keypad, the related partitions will be disarmed. In order to arm the partition using the keyswitch again, turn the key to the disarm position and then to the arm position.
. 3. Specify a two-digit zone number and press / 4. Access and configure the parameters in the Zone Sound menu, as follows: Zones: Zone Sound Quick Keys 2 4 Parameter Default Silent ZZ + 1 / Produces no sound. 2 4 Bell Only ZZ + 2 / Activates the bell sounders for the duration of the Bell Timeout period, or until a User Code is entered, followed by use of the 2 4 / key. Buzzer Only ZZ + 3 / Activates each keypad's internal piezo buzzer.
. 3. Specify a zone number and press / 4. Access and configure the parameters in the Termination menu, as follows: NOTE: When configuring the parameters in the table below, refer to Figure 2-4, Zone Connection Diagrams in Chapter 2, Mounting and Wiring the Main Panel, if required. Zones: Termination Quick Keys 2 5 Parameter Default Range N/C ZZ + 01 / Uses normally-closed contacts and no terminating End-of-Line Resistor.
2 5 / BUS Zone Input EOL ZZ + 08 Use this option to define EOL termination (see above description) for the relay zone input that exists on a BUS zone detector. 2 5 / BUS Zone Input DEOL ZZ + 09 Use this option to define DEOL termination (see above description) for the relay zone input that exists on a BUS zone detector. 2 5 / BUS Zone Input N/O ZZ + 10 Use this option to define N/O termination (see above description) for the relay zone input that exists on a BUS zone detector.
Zones: Loop Response Quick Keys 2 6 Parameter Fast ZZ + 3 / 10 ms (milliseconds). This loop response time is usually used for devices that require very quick responses, such as shockwave detectors or keyswitches. 2 6 Very Fast ZZ + 4 / 1 ms (millisecond). This loop response is usually used for shutters or other devices that require very quick responses. Note: This loop response time will be available only for zones located on the zone expander RP128EZ8F00A. 2 6 Half Hour ZZ + 5 5 = 0.
4. Select the zone pairs manually, as required, by making changes to the number of the first zone in the set, followed by the number of the second zone. If necessary, use the or / / keys to position the cursor. NOTES: Zones crossed with themselves are valid pairs. They need to register a violation twice to trigger the alarm. This process is known as Double Knock. You may want to establish a number of zone links, but leave them deactivated at this time (see below). 5.
2 8 Zones: Labels The Labels menu enables you to create and/or edit up to 15 characters to describe each of the system's zones. Default: Zone 01, Zone 02, Zone 03, Zone 04 and so on for each zone Range: Any characters ¾ To access the Labels menu: 1. Access the Zones menu, as described on page 5-18. 2. From the Zones menu, press [8] to access the Labels menu options. The following display appears: / 3. Press display appears: to label Zone 01 (or enter another zone number). The following 4.
Zones: Maintenance Quick Keys Parameter 3. Press the changed. 2 9 2 key to exit. The process is executed as the display is Delete a Zone Deactivates a designated zone by setting its Zone Type to Not Used, while maintaining all the previously programmed parameters. 1. Press [2]. / or keys or the [1 to 9] keys to 2. Use the / select the zone that is to be deleted. This process can also be used to temporarily disable a zone from the protection scheme. 3.
Zones: Maintenance Quick Keys 2 9 5 Parameter Wireless Module Calibration Measures the RF noise that the receiver is picking up. This is used for jamming indication in order to eliminate false jamming alarms. The range is 00-99. 1. Press [5]. The following display appears: 2. Select the wireless zone expander for which you want to establish the / threshold level and press showing the current threshold level: . The following display appears, 3.
Zones: Maintenance Quick Keys 2 9 6 Parameter ZZ Wireless Zone Allocation Options / + 1. Select the zone number intended for the first wireless transmitter. The first eight zones are reserved for the hardwired zones on the Main Panel. The following display appears: 2.
Zones: Maintenance Quick Keys 2 9 8 Parameter Zone Self-Test This feature provides an automated self-test for a selected group of localized intrusion sensors (for example, glass break detectors, sound discriminators and shock sensors) which respond to an artificial source of noise and/or vibration. Automated self-testing is especially useful when sensors are placed in high security areas where failure cannot be tolerated. Up to 16 zones can be designated for self-testing.
Zones: Maintenance Quick Keys Parameter 1. From the main Installer Programming menu, press [1] [1] and select option [7]. The following display appears: 2. Press / . The following display appears: 3. Press / again. The following display appears: 4. Define the time (in 24-hour format) for the first test to begin. The defaults are 00 hours and 00 minutes. The range is 00 to 24 hours and 00 to 59 minutes. 5. Use the / or / 6. Press 8. Press / keys to reposition the cursor. . / 7.
Zones: Maintenance Quick Keys Parameter 4. Press / . 5. Press [1] to select System. The following display appears: 6. Press / . The following display appears: 7. Press [8] to select the sensors test. The following display appears: 8. Press / . 9. Select the manner in which the UO is to operate, by choosing [2] PULSE N/O. The following display appears: 10. The UO, acting like a normally-open switch, is closed for a predetermined period, completing a circuit that activates a noise source. 11.
Zones: Maintenance Quick Keys Parameter 2. To put a zone on Soak Test, press appears: / . The following display 3. Press the keys as per the zone number (e.g. 001 for zone 1), as shown in the following display: 4. Press / . 5. To add a second zone for Soak Test, press the procedure above, / and repeat -ORPress the 2 0 key to return to the previous menu.
Zones: Miscellaneous Quick Keys Parameter Default 1. Press [1] and then press / Range . The following display appears: 2. Enter the number of the zone for forced arming and press 3. Use the / DISABLE and press or / / / . keys to select ENABLE or . The following display appears: 4. Repeat steps 1 to 3 to change the forced arm status of any additional zone. 2 0 2 key to exit. 5.
Zones: Miscellaneous Quick Keys 2 0 Parameter Default Range BUS Zone Parameters 3 The BUS Zone Parameters menu contains parameters that enable you to program the special parameters of a BUS zone. The options are determined according to the BUS detector type: ♦ Lunar Grade 3: A dual technology ceiling detector with a mounting height of up to 8.6m (28ft) that incorporates Anti-CloakTM Technology (ACT).
Zones Miscellaneous: BUS Zone – iWISE DT Grade 2 Quick Keys 2 0 3 ZZ 2 Parameter Default MW (Microwave) Range Trimmer Range Defines the microwave channel range. [1] Minimum [2] 25% [3] 50% [4] 65% [5] 85% [6] Maximum [7] Trimmer (MW is defined by the trimmer setting on the PCB) 2 0 3 ZZ 3 ACT No Defines the Anti-Cloak™ Technology (ACT) operation mode. [1] No - Disables the ACT mode. [2] Yes - Enables the ACT mode.
Zones Miscellaneous: BUS Zone – Lunar Grade 3/iWISE DT Grade 3 Quick Keys 2 0 3 ZZ 3 Parameter Default ACT No Range Defines the Anti-Cloak™ Technology (ACT) operation mode. [1] No - Disables the ACT mode. [2] Yes - Enables the ACT mode. 2 0 3 ZZ 4 Automatic Microwave Bypass No Defines whether the MW channel will be bypassed or not while the detector identifies trouble in the MW channel. [1] No - While detecting a problem in the MW channel it is not bypassed.
Zones Miscellaneous: BUS Zone – iWISE QUAD Grade 2 Quick Keys 2 0 3 ZZ 1 Parameter Default LEDS On Range Defines the LEDS operation mode. [1] Off - Disables the LEDS operation. [2] On – Enables the LEDS operation. 2 0 3 ZZ 2 Sensitivity High Defines the sensitivity of the detector (PIR). [1] Low [2] High 2 0 3 ZZ 3 Self Test Remote Used to test detection technologies. In the event of a failed test, a Self Test Trouble is created.
Zones Miscellaneous: BUS Zone – WatchOUT PIR Quick Keys 2 0 3 ZZ 1 Parameter Default LEDS 3 LEDS Range Defines the LEDS operation mode. [1] Off - Disables the LEDS operation. [2] Red Only - Only the Red LED will operate. This option is highly recommended to avoid the possibility that a burglar will “Learn” the detector behavior. [3] 3 LEDS - All 3 LEDs will operate. 2 0 3 ZZ 2 PIR Sensitivity Normal Defines the PIR sensitivity of the detector.
Zones Miscellaneous: BUS Zone – WatchOUT DT Quick Keys 2 0 3 ZZ 4 Parameter Default Alarm Logic PIR and Microwave Range Determine the detector’s logic of defining an alarm. [1] PIR and Microwave – An alarm is activated when both PIR and MW channels detect an alarm (AND Logic). [2] PIR or Microwave - An alarm is activated when either PIR or MW channels detect an alarm (OR Logic). 2 0 3 ZZ 5 Lens Type Wide Angle Defines the actual Lens of the detector.
Zones Miscellaneous: BUS Zone – WatchIN DT Grade 3 Quick Keys 2 0 3 ZZ 4 Parameter Default Alarm Logic PIR and Microwave Range Determine the detector’s logic of defining an alarm. [1] PIR and Microwave – An alarm is activated when both PIR and MW channels detect an alarm (AND Logic). [2] PIR or Microwave - An alarm is activated when either PIR or MW channels detect an alarm (OR Logic). 2 0 3 ZZ 5 Lens Type Wide Angle Defines the actual Lens of the detector.
3 Utility Output The Utility Output menu provides access to submenus and their related programming parameters that enable you to choose the event that will trigger a selected Utility Output, as well as the manner in which the output will be applied. Adding one or more Utility Output expansion modules to the system makes an extensive list of switched output possibilities available.
2. Press 3 1 / to disable the selected utility output. Utility Output: System The System menu contains Utility Output parameters that follow the System Event. ¾ To access the System menu: 1. Access the Utility Output menu, as described on page 5-47. 2. From the Utility Output menu, press [1] to access the System menu options. The following display appears: 3. Press / . The following display appears: 4.
Utility Output: System Quick Keys 3 1 05 Parameter Ground Pulse Activates when the ProSYS dialer dials out. This option is rarely used and is intended for older phone systems that require a "Ground Start" (a momentary connection between one side of the phone line and "earth") to obtain a dial tone. When the Utility Output is programmed (and properly wired) for this purpose, it provides the 2-3 pulses needed to furnish a dial tone to the dialer.
Utility Output: System Quick Keys 3 1 Parameter Digital Key Reader Communication 13 This Utility Output is activated when there is a BUS communication problem with the Proximity Key Reader. The pattern of the operation is Pulsed, and the default is 01 second for the pulse duration. The Utility Output will be activated for 5 consecutive times between the time that the Main Panel identifies a communication problem with the Digital Key Reader and the time it sends a restore event.
4. Select the partition event to be followed from those listed below, using the / or / keys to move the cursor left or right, respectively. Utility Output: Partition Quick Keys 3 2 01 Parameter Ready Follow Activates the Utility Output when all the selected partition(s) are in the READY state. 3 2 02 Alarm Follow Activates the Utility Output when an alarm occurs in the selected partition(s).
Utility Output: Partition Quick Keys 3 2 11 Parameter Exit/Entry Follow Activates the Utility Output when the selected partition(s) initiates an Exit/Entry Delay period. 3 2 12 Fire Trouble Follow Activates the Utility Output when a FIRE TROUBLE is detected in the selected partition(s). 3 2 13 Day (Zone) Trouble Activates the Utility Output when a DAY ZONE TROUBLE is detected in the selected partition(s).
Utility Output: Partition Quick Keys 3 2 Parameter Zone Loss Alarm 22 An alarm is activated when a wireless zone is lost. 5. Press / . The following display appears: NOTE: The XX in the UO=XX refers to the number of the Utility Output currently being programmed. / key to toggle between [Y] YES and [N] NO to designate the 6. Use the partition(s) that will activate the selected Utility Output (UO), -ORPress the partition number [1 to 8] to select or deselect it. 7.
Utility Output: Zone Quick Keys 3 3 Parameter Disarm Follow 4 Activates the Utility Output when the selected zones are disarmed. 5. Press / . The following display appears: / 6. Enter the zone numbers in the group and press Utility Output, you can define a group of up to five zones. after each one. For each NOTE: If you choose a zone number that is not in the system, a broken line is displayed (---). / and proceed to Pattern of Operation, page 5-54, to set the pattern 7.
Utility Output: Pattern of Operation Quick Keys 3 4 1 Parameter Default Range Pulse N/C 05 seconds 01-90 seconds The Utility Output is always Activated (N/C) before it is triggered (pulled down to negative). When triggered, it deactivates for the Pulse Duration specified below and then reactivates automatically. 1. Press [1] and then press / . 2. Choose the desired Pulse Duration, between 01-90 seconds. 3 4 2 3. Press / and set the activation by choosing ALL or ANY. 4. Press below).
Activation/Deactivation When the Utility Output is following more than one Partition or Zone, the Installer can choose the logic of the Utility Output activation or deactivation, as follows: ♦ If the Pattern of Operation is defined as Latch N/O or Latch N/C, the Installer can choose the activation and deactivation logic of the UO to follow either after all the Partitions/Zones or after any of the Partitions/Zones.
4 Code Maintenance The Code Maintenance menu provides access to submenus and their related parameters that enable you to maintain the User Codes in the system. In addition, the ProSYS contains the following special codes: ♦ Grand Master Code: Used by the system's owner or chief user. ♦ Installer Code: Used by the ProSYS installation company technician to program the Main Panel.
4 1 Code Maintenance: Authority Default: User The Authority menu enables you assign the Authority Level of each User Code. There are seven Authority Levels to match the needs of various users, as described in Authority Levels, below. ¾ To access the Authority menu: 1. Access the Code Maintenance menu, as described on page 5-57. 2. From the Code Maintenance menu, press [1] to access the Authority menu. The following display appears: 3.
♦ ♦ ♦ ♦ ♦ 4 2 Activating designated Utility Outputs Changing his/her own User Code Controlling uploading/downloading activities Administering selected system tests, except Walk Testing Arm Only: There are no restrictions in the number of Arm Only Codes (as long as they don't exceed the number of codes remaining in the system).
8. When you have completed the process, press the 4 3 key to return to the previous level. Code Maintenance: Grand Master Default: 1234 The Grand Master menu enables the owner or chief user to set the Grand Master Code. NOTE: The Grand Master code can also be changed in the User menu (by the Grand Master). The Grand Master is the highest Authority Level. Refer to Authority Levels, page 5-58, for additional details about other authority levels. ¾ To access the Grand Master menu: 1.
6. Press the 4 5 key to return to the previous level. Code Maintenance: Sub-Installer Default: 0228 The Sub-Installer Code allows limited access to selected parameters from the Installer Programming menu.
4 6 Code Maintenance: Code Length Default: 4 digits The Code Length specifies the number of digits (either 4 or 6) for the Grand Master, Manager, and Master Codes. All the other codes (User, Arm Only and Maid) use from one digit up to a maximum of six digits. ¾ To access and program the Code Length menu parameters: 1. Access the Code Maintenance menu, as described on page 5-57. 2. From the Code Maintenance menu, press [6] to access the Code Length menu. The following display appears: / . 3. Press 4.
Code Maintenance: Code Length Quick Keys Parameter NOTES: When you change the Code Length parameter, all User Codes are deleted and must be reprogrammed or downloaded. For a 6-digit Code Length system, 4-digit default codes like 1-2-3-4 (Grand Master), 0-1-2-8 (Installer), and 0-2-2-8 (Sub-Installer) become 1-2-3-4-0-0, 0-1-2-8-0-0, and 0-2-2-8-0-0, respectively. If you change the Code Length back to 4 digits, the system codes are restored to the default 4-digit codes.
Dialer 5 The Dialer menu provides access to submenus and their related parameters that enable ProSYS to establish communication with the MS and transmit data.
3. Access and configure the parameters in the Link-Up menu, as follows: Dialer: Link Up Quick Keys 5 1 Parameter Range MS Link-Up 1 The ProSYS enables to report events to the MS receiver in four connectivity (link-ups) options, depending on the communication options at the MS site: 1. Voice channel (land line or GSM): Up to 32 alphanumeric characters 2. TCP/IP (using the ACM) 3. SMS (using the GSM/GPRS module) 4.
Dialer: Link Up Quick Keys 5 1 1 Parameter 1 2 Range IP The ProSYS will report the MS over TCP/IP network using the Advanced Communication Module (ACM). 1. Type in the IP address that identifies the MS receiver on the network. 2. Press / the network. 5 1 1 1 3 and type in the MS Port address of the receiver on SMS The ProSYS will report the MS via SMS using the GSM/GPRS module. Type in up to 32 digits of the MS phone number with prefix included.
Dialer: Link Up Quick Keys 5 1 2 1 Parameter Range U/D Phone 1 Up to 32 alphanumeric characters Type in up to 32 digits followed by and area code or special letters. 5 1 2 U/D Phone 2 2 / . Include dialing prefixes Up to 32 alphanumeric characters The second number for the U/D software Special Letters When entering special letters, you must press and hold the required number at the same time without releasing the letter, you must release the letter. key and then press the key.
3. Use the / or / keys to select a partition and press / . If you select partition 1 or 2 in the ProSYS 40 or ProSYS 128,the following display appears: 4. Select the MS telephone number (up to three available numbers) and press / . The following display appears: NOTE: This display also appears if you selected partitions 3-8 in step 3. 5. Define a different account number for each MS telephone number. NOTE: For partitions 3-8, the same account number will be sent to all three MS telephone numbers.
4. Use the [0 to 9] keys to assign the format code (for example, 0420 ADEMCO Contact ID format. 5. Press / 6. Press / . again followed by the key to return to the previous level. NOTE: For SIA and Contact ID formats, refer to Dialer: Auto Codes, page 5-85. 7. Access and configure the parameters in the Communication Format menu, as follows: Dialer: Communication Format Quick Keys 5 3 1 Parameter Default Format for MS Tel No. 1 0000 Defines the protocol format for the first MS telephone number.
Monitoring Station (MS) Communication Formats Protocols Communication Formats Format Code DTMF, Parity 0420 Most Common Protocols: ADEMCO Contact (Point) ID SIA Level 0700 Simple Pulse Protocols: Silent Knight/ADEMCO Slow 010F Silent Knight/ADEMCO Slow-Extended 014F Radionics/DCI/Franklin Slow 0117 Silent Knight Fast 010E Silent Knight Fast-Extended 014E Sescoa/Franklin/Vertex/DCI Fast 0116 Sescoa/Franklin/Vertex/DCI-Extended 0156 Universal High Speed Non-Extended 0112 Radionics Proto
5 4 Dialer: Access and ID The Access and ID menu enables you to set the access and ID Codes for communication between the technician and the installation using the Upload/Download software. ¾ To access the Access and ID menu: 1. Access the Dialer menu, as described on page 5-64. 2. From the Dialer menu, press [4] to access the Access and ID menu options. The following display appears: 3.
Dialer: Access and ID Quick Keys 5 4 3 Parameter Default MS Lock 000000 MS Lock is a security function used in conjunction with RISCO Group's Upload/Download software. It provides greater proprietary security when viewing MS parameters. The same 6-digit code, which will be stored in the panel, must be entered into the corresponding account profile created for the installation in the Upload/Download software.
Dialer: Controls Quick Keys 5 5 02 Parameter Default FM Enable YES YES: Enables Follow-Me communication. (Refer to Follow-Me, page 5-79.) If both the MS phones and the FM phones are defined, the system will first call the MS phones and then the FM phones. NO: Disables Follow-Me communication. 5 5 03 U/D Enable YES YES: Enables communication between the MS and the ProSYS Main Panel using the Upload/Download software.
Dialer: Controls Quick Keys 5 5 09 Parameter Default Auto Batch NO YES: The ProSYS Main Panel calls the MS’s computer at a preset time. (Refer to Dialer: Periodic Test, page 5-84.) The Upload/Download software downloads a batch of previously programmed installation data from the MS to the account. NOTE: For the Auto Batch parameter to work: The computer must be turned on, connected to a phone line, and have the Upload/Download software loaded. -ANDThe call must be initiated by the account.
Dialer: Controls Quick Keys 5 5 14 Parameter Default Audible Kissoff NO YES: There is an audible sound emitted from the keypad when the dialer receives the kissoff signal from the MS’s receiver. NO: There is no audible sound on receipt of the kissoff signal. 5 5 15 Upload /Download GSM Enable NO This option allows performing remote Uploading /Downloading using the GSM/GPRS module through the data channel. NOTE: The data channel on the SIM card must be enabled.
Dialer: Parameters Quick Keys 5 6 1 Parameter Default Range MS Retries 08 01 to 15 The number of times the ProSYS redials the MS after failing to establish communication. 5 6 2 5 6 3 03 FM Retries 01 to 15 The number of times the Follow-Me phone number is redialed. 12 Rings to U/D 01 to 15 The number of rings before the ProSYS answers an incoming call (for remote programming). NOTE: When the Answering Machine Override parameter is enabled (refer to page 574), this parameter is ignored.
Dialer: Parameters Quick Keys 5 6 6 Parameter 1 Select [1] and press 5 6 6 2 6 6 3 6 / / to activate the Pulse @ 20 BPS dialing / to activate the Pulse @ 10 BPS dialing 61/39% Pulse Duty Cycle 7 to activate the DTMF dialing method. Pulse @ 10 BPS (pulses per second) Select [3] and press method. 5 Range Pulse @ 20 BPS (pulses per second) Select [2] and press method.
Press [1 to 4] to enter a report category. For each category, enter the number of the option you want to assign to the category or choose it by using the / or / keys and press / . key to return to the Dialer menu. Press the Dialer: Report Split Quick Keys 5 7 1 Parameter Default MS Arm/Disarm 1st Backup 2nd Reports Arming/Disarming (meaning Closings/Openings) events to the MS. 5 7 1 1 5 7 1 2 5 7 1 3 Do Not Call Does NOT report Openings and Closings.
Dialer: Report Split Quick Keys 5 7 4 Parameter Default By Partition FOLLOW ME In addition to reporting to the MS, the ProSYS has a Follow Me feature which enables reporting a system event to a predefined phone or email (using the ACM module or GSM/GPRS module). Up to 8 Follow Me types can be defined in ProSYS 16 and ProSYS 40 and up to 16 can be defined in ProSYS 128. This procedure is useful to alert a homeowner at work, or a business owner at home, of an alarm.
Dialer: Report Split Quick Keys 5 7 4 Parameter FM 1 Default Follow-Me Type This option allows you to configure the format of the message sent to the Follow Me destination, in an occurrence of an event. Use the or 5 7 4 7 4 FM 1 FM 1 / / keys until the required option is received. Voice 1 Events are reported to the Follow Me number by voice messages 5 SMS 2 Events are reported to the Follow Me number by SMS.
Dialer: Report Split Quick Keys Parameter Default [03] Emergency Y [04] Panic Y [05] Tamper N [06] Remote Programming N [07] AC Off N [08] Duress Y [09] Arm N [10] Disarm N [11] Bypass N [12] Wireless Lost N (When no supervision signal from the wireless zones is received.) [13] Wireless Low Batt N (wireless zone or keyfob) [14] Bell Trouble N [15] False Code N (When a wrong User Code is entered more than 3 times.
Dialer: Report Split Quick Keys 5 7 4 Parameter FM 4 Default Follow-Me Restore Specifies which events will activate this Follow-Me destination in the partitions assigned to the Follow-Me destination. / Use the or the list below, and then use the to select [Y] YES or [N] NO. / keys to select the events from / and / keys [01] Intruder [02] Tamper Y N [03] AC Off N [04] Wireless Lost N (When no supervision signal from the wireless zones is received.
Dialer: Report Split Quick Keys Parameter Default [6] SMTP User Name: A parameter that defines the user name that the SMTP server requires for authentication when defined as such by the IT department. Up to 21 characters can be used. [7] SMTP Password: A parameter that defines the password that the SMTP server requires for authentication when defined as such by the IT department. Up to 21 characters can be used.
5 9 Dialer: Periodic Test The Periodic Test menu enables you to set the time period that the ProSYS will automatically call the MS or Upload/Download phone numbers in order to check the phone line connection. It also sends reports of non-urgent events, which reduces the number of calls made (only if the Call Save option is defined as YES). (Refer to Call Save, page 5-73, for additional details). ¾ To access the Periodic Test menu: 1. Access the Dialer menu, as described on page 5-64. 2.
Dialer: Periodic Test Quick Keys 5 9 2 Parameter Default Range UD Test HR:00 MIN:00 00-24 hours 00-59 minutes Used to schedule periodic Auto Batch download using the Upload/Download software. This is the day, time of day (in 24-hour format) and time interval at which the customer's ProSYS automatically calls the MS’s computer to download the Batch (selected parameters). For additional details, refer to the Upload/Download User's Manual. Set the test time and daily interval, as follows: 1.
Dialer: More Quick Keys 5 0 Parameter Auto Codes 1 The Auto Codes menu enables the resetting of all MS Report Codes to 00 without the need to restore factory defaults for the auto setting of the following MS formats: ♦ SIA ♦ ADEMCO Contact ID 5 0 1 1 Contact ID The ProSYS allocates Report Codes supporting ADEMCO Contact (Point) ID. / to select this option and deselect the 1. Press SIA option (described below). The following display appears: 2. Press / and / to confirm your choice.
Dialer: More Quick Keys Parameter NOTE: Any change in the system parameters requires you to reload the Auto Codes parameters in order to update the information that is being sent to the MS. ACM Parameters 5 0 2 5 0 2 1 ACM IP Address 5 0 2 2 The static IP address that identifies the ACM module on the network. 03000 ACM UD Port 5 0 2 3 The port address of the ACM U/D application. 00502 ACM AUX 1 Port See ACM Installer Manual for more information. 192.168.001.
Dialer: More Quick Keys 5 0 3 Parameter 1 ACM Configuration Defines the ACM parameters configuration. [1] Client ATN (default N): Provision for optional functionality 5 0 3 2 [2] DHCP IP (default N): Defines whether the IP address, which the ACM refers to, is static or dynamic.
Dialer: More Quick Keys Parameter st nd 1 Backup 2 3 rd 1 Backup 3rd Call 2 Primary If (MS#1 is OK) Secondary else (MS#1 Fails) Backup Primary 2nd Backup 3rd Call 1 Primary Primary st Primary If (MS#2 is OK) Secondary else (MS#2 Fails) Backup If (MS#1 is OK) Secondary else (MS#1 Fails) Backup If (MS#2 is OK) Secondary else (MS#2 Fails) Backup NOTE: The installer must manually enter the report code value of 87 under the Report Codes programming menu using quick keys [6][8][0][4].
6 Report Codes The Report Codes menu enables you to program the codes transmitted by the ProSYS to report events (for example, alarms, troubles, restores, and supervisory tests) to the MS, as follows: ♦ The codes specified for each type of event transmission are a function of the MS’s own policies. Before programming any codes, it is important to check the MS protocols. ♦ While most Communication Formats support the Report Codes detailed in the following pages, some do not (refer to page 5-68).
6 1 Report Codes: Emergency Key The Emergency Key menu enables you to define the codes transmitted to the MS when an alarm is sent (meaning Police, Fire, and Auxiliary Emergency) via a keypad's emergency keys. ¾ To access the Emergency Key menu: 1. Access the Report Codes menu, as described on page 5-90. 2. From the Report Codes menu, press [1] to access the Emergency Key menu options. The following display appears: 3.
6 2 Report Codes: Zones The Zones menu contains parameters of the Report Code generated when an alarm (or alarm restoral) occurs due to the violation of an armed zone. ¾ To access the Zones menu: 1. Access the Report Codes menu, as described on page 5-90. 2. From the Report Codes menu, press [2] to access the Zones menu options. The following display appears: 3. 4.
Report Codes: Zones Quick Keys 6 2 8 Parameter Default Low Battery 00 To report a low battery condition in a wireless transmitter. 6 2 9 Low Battery Restore 00 To report the correction of a low battery condition. 6 3 Report Codes: Accessory Tamper The Accessory Tamper menu contains codes that enable reporting the violation (or restoral) of the tamper switch on a system accessory (a keypad or expansion module). Keypads have built-in tamper switches.
6 3 Event Logger 4 00 [1] Event Logger Tamper: Tamper Codes for event logging modules. [2] Event Logger Tamper Restore: Tamper Restore to Normal Report Code for event logging modules. 6 3 Wireless Button Accessory 00 5 [1] Wireless Button Accessory Tamper: Tamper Code for wireless buttons used in the installation. [2] Wireless Button Accessory Tamper Restore: Tamper Restore to Normal Code for wireless buttons used in the installation.
Report Codes: Main Trouble Quick Keys 6 4 1 Parameter Default Trouble Conditions 00 Trouble Codes assigned to the Power Supply Accessory module: [1] Low Battery: reports the detection of a weak (or missing) standby battery. [2] Bell: reports a trouble condition with the management of an internal sounder wired to the Main Panel. [3] Phone: reports a trouble condition regarding telephone service management. [4] AC Loss: reports a trouble condition regarding the AC power supply to the ProSYS.
6 5 Report Codes: Power Supply Accessory Module Trouble Default: 00 The Power Supply Accessory Module Trouble menu contains codes that enable reporting the detection or restoral of troubles relating to the operation of the Power Supply Accessory module. ¾ To access the Power Supply Accessory Module Trouble menu: 1. Access the Report Codes menu, as described on page 5-90. 2. From the Report Codes menu, press [5] to access the Power Supply Accessory Module Trouble menu options.
Report Codes: Power Supply Accessory Module Trouble Quick Keys Parameter Default [4] AUX: reports the restoring to normal of the Auxiliary power supplied by the Power Supply Accessory module. [5] Overload: A report code for user initiated overload restore (User menu [*] [2] [0] [5]). 6 6 Report Codes: Arm Codes (Closings) The Arm Codes menu contains codes that enable the reporting of the Closing Signals generated when the system is ARMED (closed under a variety of conditions).
Report Codes: Arm Codes Quick Keys 6 6 6 6 Parameter Default 5 Quick Armed 00 6 The 2-digit Report Code used when the system is Quick Armed. NOTE: No specific user identification is possible. Refer to the ProSYS User's Manual for additional details. 00 Forced Arm A Report Code used when the system is Force Armed. 6 6 Wireless Button Armed 7 00 1. Enter the 2-digit Wireless Button ID. 2. Enter the 2-digit Report Code transmitted when the system is armed with this specific device.
Report Codes: Disarm Codes Quick Keys 6 6 7 7 Parameter Default 3 Auto Disarmed 00 4 Report Code used when the system is Auto Disarmed by a previously scheduled event. NOTE: No specific user identification is possible. Refer to the ProSYS User's Manual for additional details. 00 Remote Disarmed Report Code for Remote Disarming by the MS using its Upload/Download software. 6 7 Wireless Button Disarmed 00 5 Code to report disarming with this device.
Report Codes: Miscellaneous Quick Keys 6 8 4 Parameter Default Periodic U/D Test 00 Report Code for the system's periodic Upload/Download (Auto Batch) transmissions. 6 8 5 6 8 6 6 8 7 Call Back Request 00 Report Code for automatic callback to the MS’s Upload/Download software. System Reset 00 Report Code for manual reset using the ProSYS DEFAULT (J2) jumper. Abort Alarm 00 Report Code used when the system sends an ABORT message to the MS.
Report Codes: Miscellaneous Quick Keys 6 8 0 4 Parameter Default Polling 00 Defines the value that represents the polling signal of the IP and GPRS report channels (for SIA and Contact ID). 6 9 Report Codes: Special Communication The Special Communication menu enables you to program the 3-digit Report Codes for MS Communication Formats requiring 3-digit Event Codes. Refer to the ProSYS Installer Programming Worksheets for additional details. ¾ To access the Special Communication menu: 1.
Report Codes: Accessory Code Quick Keys 6 0 1 1 Parameter Default Jamming Trouble 00 1. Enter the Wireless Zone Expander's 1-digit physical ID. 2. Enter the 2-digit Report Code for the module's detection of jamming interference, according to the parameters established on page 5-4. 6 0 1 2 Jamming Trouble Restore 00 1. Enter the Wireless Zone Expander's 1-digit physical ID. 2. Enter the 2-digit Report Code for the restore to normal detection of interference (see above).
Report Codes: Accessory Code Quick Keys 6 0 3 3 Parameter Default Printer Buffer Full 00 Report Code for a full buffer in the module (a printing difficulty). The event will be sent if the buffer is full (above 75% of its capacity). 6 0 3 4 Printer Buffer Full Restore 00 Report Code for the restoral-to-normal of the module's buffer. The restoral will occur once the buffer decreases to 75% of its capacity.
Report Codes: Accessory Code Quick Keys 6 0 6 Parameter 1 Default Trouble 00 Report codes for GSM faults: [1] Tamper: report code of GSM box tamper alarm condition. [2] Communication Trouble: report code of communication trouble between the GSM module and the ProSYS. [3] Mains Trouble: report Code of loss of main power to the GSM module. [4] Low Battery: report code for low battery condition.
7 Accessories The Accessories menu provides access to submenus and their related parameters that enable you to add to or remove keypads and expansion modules.
Accessories: Add Delete Module Quick Keys 7 1 1 Parameter Default Keypad LCD Range STEP 1: CHOOSING A KEYPAD TYPE: 1. Press [1]. The following display appears: 2. Use the / or / keys to position the cursor over the keypad ID number for which you want to assign (or delete) a keypad. The first keypad must be assigned to the first ID number, which is 01.
Accessories: Add Delete Module Quick Keys Parameter Default Range NOTES: 1. Non-partitioned systems are regarded as Partition 1. This partition specifies the location of the keypad and is mainly used for quick arming. Pressing the Arm Key automatically arms the partition. 2. In partitioned systems, keypads can be selectively assigned to specific partitions, but LED-type keypads can be used only in systems that do not exceed their ability to display zone indications.
Accessories: Add Delete Module Quick Keys Parameter Default Range BZ08 ( Virtual 8 Zone Expander) BZ16 (Virtual 16 Zone Expander) G3Z08 (an 8 Hardwired Zone Expander with TEOL termination) G3Z16 (a 16 Hardwired Zone Expander with TEOL termination) BZE08 (8 BUS zone expander) BZE16 (16 BUS zone expander) BZ24 (24 BUS zone expander) BZ32 (32 BUS zone expander) / 4. Press to confirm (and store) your choice. 5.
Accessories: Add Delete Module Quick Keys Parameter Default Range If a Utility Output module is found and NONE has been selected, the following display appears: 7. Press / to return to the prior display. -OR/ Press confirm the delete. 7 1 4 to select [Y] YES and press Power Supply Module / to NONE 1. Press [4]. The following display appears: 2. Use the / or / keys to position the cursor over the ID number to which you want to assign (or delete) the Power Supply module.
Accessories: Add Delete Module Quick Keys Parameter 9. Press Default Range to return to the previous programming level. If a Power Supply module is found and NONE has been selected, the following display appears: 10. Press / to return to the previous display, -OR/ Press confirm the delete. 7 1 5 to select [Y] YES and press Event Logging Module / to NONE The event log stores events with their zone, UO number, and user number and time.
Accessories: Add Delete Module Quick Keys 7 1 6 Parameter Default Wireless Button Module NONE Range The Wireless Button module is a wireless receiver add-on designed to process signals from up to eight handheld wireless button transmitters. Each wireless button transmitter (p/n RP128T4RC00A) is a rolling code transmitter with the following options: ARM, DISARM, PANIC, and UO ACTIVATION. 1. Press [6]. The following display appears: 2.
Accessories: Add Delete Module Quick Keys Parameter Default Range PRNA (prints Access Control events) PRN2 (prints both of the above) (If you use this option, you cannot define a second printer.) 4. Press / to store your choice and to repeat the process if there is a second Printer module in the system. NOTE: You can define two printers in the system, but both printers cannot print the same events. 5.
Accessories: Add Delete Module Quick Keys Parameter Default Range Select 1 door, 1 reader to initialize one door, and then proceed to step 7. -OR Select 1 door, 2 readers to initialize one door, and then proceed to step 6. -OR Select 2 doors, 2 readers to initialize two doors, and then proceed to step 7. 6. If you selected 1 door, 2 readers in step 5, then toggle the / and / keys to define the antipassback feature, as described / below, and then press .
Accessories: Add Delete Module Quick Keys Parameter Default Range KEY RAEDER: ID=01 TYPE=PKR 3. Use the / or / keys to position the cursor at ID=1 and type in the Proximity Key Reader ID number as defined by the dip switches that you set when you installed the module. 4. With the cursor positioned at the TYPE field, use the to toggle and choose the PKR option. 5. Press / 6. Use the / key . The following display appears: / key to toggle and choose [Y] YES.
Accessories: Add Delete Module Quick Keys Parameter Default Range If YES, the Bypass status will be indicated on the reader.If NO, no Bypass status indication will be indicated on the reader / . 14. Press NOTE: Recording tags can be performed only from Proximity Key Reader ID number 1. 7 1 9 2 Advanced Digital Voice Module 1. Press [2]. The following display appears: 2. With the cursor positioned at the TYPE field, use the to toggle and choose the VOICE option. 3. Press / / key .
Accessories: Add Delete Module Quick Keys Parameter Default Range P=12345678 S=1 Y....... 5. Use the / or / number and then use the / NO to assign that partition to the siren. 6. Press / . SIREN=1 SOUND? The following display appears. Y / 7. Use the deactivate the sound. 8. Press keys to select a partition key to toggle [Y] YES or [N] / key to toggle [Y] YES or [N] NO to activate or . The following display appears. SIREN=1 SQUAWK SOUND? Y / key to toggle [Y] YES or [N] NO.
Accessories: Add Delete Module Quick Keys Parameter Default Range NOTE: Make sure that the detector's physical ID number is identical to the ID number you select during programming. 3.
7 2 Accessories: Verify Module The Verify Module menu provides a verification list of the modules in accordance with the modules you defined in the Add Delete Module menu (page 5-105) or in the Auto Settings menu (page 5-119). ¾ To access the Verify Module menu: 1. Access the Accessories menu, as described on page 5-105. 2. From the Accessories menu, press [2] to access the Verify Module menu options. The following display appears: / or / keys to scroll down the list of displayed 3.
A result of less than 100% means that there are BUS connection problems (for example, bad wiring or cabling located in a harsh electrical environment or two modules in the same family have been given the same ID number). 7 4 Accessories: BUS Scanning The BUS Scanning menu scans the BUS and reports all modules found. ¾ To access the BUS Scanning menu: 1. Access the Accessories menu, as described on page 5-105. 2. From the Accessories menu, press [4] to access the BUS Scanning menu options.
¾ To access the Auto Settings menu: 1. Access the Accessories menu, as described on page 5-105. 2. From the Accessories menu, press [5] to access the Auto Settings Install menu. The Auto Settings process runs the BUS scanning. (Refer also to Accessories: BUS Scanning, page 5-119.) A list of the accessories that were found is displayed with the data definition that is required for each one. 3.
8 Miscellaneous Default: NONE The Miscellaneous menu contains submenus that enable you to define the parameters of various accessories: ¾ 8 1 Key-fob, below 8 2 Siren, page 5-124 8 3 GSM, page 5-125 To access the Miscellaneous menu: ♦ From the main Installer Programming menu, press [8] or press the / or / keys until you find the number [8] Miscellaneous option and then press / .
4. Press / . Changing the Wireless Button Parameters Each wireless button consists of 4 keys, and each key can be programmed to a different mode of operation. ¾ To change the wireless button parameters: 1. Assign the relevant partitions for the selected button. 2. Set the parameters for the Arm Key #1 (±) (used to perform the Away Arming operation) from the following options: NONE: The key is disabled (default). AWAY: The key is used for AWAY arming the assigned partitions.
8. Set the parameters for the UO Key #4 from the following options: NONE: The key is disabled (default). AWAY: The key is used for AWAY arming the assigned partitions. STAY: The key is used for STAY arming the assigned partitions. GROUP: The key is used for GROUP arming the assigned partitions UO: The key is used to operate a Utility Output. When selecting this option, you must select a Utility Output: NOTE: Away or STAY arming can be defined as instant or delayed (Exit Delay). 9.
8 2 Miscellaneous: Siren The Siren menu enables defining all parameters of an external siren that can be connected to the ProSYS as a BUS accessory. Up to 8 sirens can be added to the ProSYS and each can be assigned to any partition. Connection to the BUS enables Remote Control and Diagnostic support for a siren. Siren Parameters Quick Keys 8 2 1 Parameter Default Strobe Control Follow Bell Defines the Strobe operation mode [1] Always Off - The strobe is deactivated.
8 3 Miscellaneous: GSM RISCO Group's GSM/GPRS BUS Module is a cellular communication module for use with RISCO Group security panels that can be used as a backup or a substitute to a normal PSTN line. Reporting to the MS can be performed using Voice, SMS or GPRS channel using RISCO Group's IP/GSM Receiver at the MS site. Reporting to the user can be performed using Voice messaging, SMS or E-mail (using GPRS).
GSM Parameters Quick Keys 8 8 3 1 3 2 1 2 2 Parameter Default GSM Lost 10 minutes 001-255 minutes The time after which the module will switch over to the PSTN line upon GSM network lost. Notes: 1) Network loss is defined as RSSI level below the level defined in the minimum RSSI LEVEL parameter (Quick key [8][2][1][8]). 2) This parameter is relevant only for GSM/GPRS full version module. 00 00-36 Months 3 SIM Expire Date A Pre-paid SIM card has a defined life length defined by the provider.
GSM Parameters Quick Keys 8 3 3 to 1 Parameter Default Prefix Constant 3 8 A number that is not to be corrected by the algorithm when calling from the GSM network, for example cellular telephone prefixes.
GSM Parameters Quick Keys 8 3 1 5 Parameter 2 Default GPRS User Name Enter user name for the GPRS network (if required). The User name is provided by your provider. The ProSYS supports a user name field of up to 20 alphanumeric characters and symbols (!, &, ? etc). 8 3 1 5 3 GPRS User password The password to the GPRS network as provided by your provider (if required). The ProSYS supports a user name field of up to 20 alphanumeric characters and symbols.
GSM Parameters Quick Keys Parameter Default Note: The installer must manually enter the report code value of 87 under the Report Codes programming menu using quick keys [6][8][0][4]. This value represents SIA code ZZ and Contact ID code 999 that are used to validate the report process.
GSM Parameters Quick Keys 8 3 1 Parameter 6 3 Default SMTP User name A name identifying the user to the SMTP mail server The user name field can include up to 10 alphanumeric characters and symbols (!, &, ? etc). Provision for future functionality. 8 3 1 6 4 SMTP Password The password authenticating the user to the SMTP mail server The password can include up to 10 alphanumeric characters and symbols (!, &, ? etc).
8 3 2 GSM Control This sub menu enables to program parameters allowing proper operation of the GSM module Devices: GSM Quick Keys 8 3 2 1 Parameter Default Disable Incoming Call No This parameter is used to disable all incoming calls trying to come in via the GSM voice channel. Notes: 1. Only SMS or Upload/Download incoming calls are allowed. 2. This parameter is relevant only for GSM/GPRS full version module.
9 Access Control Default: NONE The Access Control menu enables you to define all the parameters for the Access Control module.
Access Control: Door Define Quick Keys 9 1 Parameter Default Range Partitions 1 Defines which partitions are assigned to the door. / 1. Press [1] and then press / or 2. Use the number and then use the / the door. 3. Press NOTE: . / keys to select a partition key to toggle [Y] YES or [N] NO to assign that partition to / . The logic that stands behind the partitions that are assigned to the door is to create a walking path.
Access Control: Door Define Quick Keys 9 1 2 3 Parameter Default Range Door Alarm Delay 10 seconds 1-99 seconds Determines the amount of time that the door can remain open before an alarm is activated (triggered on relay 3). This option also determines the amount of time that passes until an alarm is activated when the door is forced open. 1. Press [2] and / to enter the door time settings. 2. Press [3] and / . 3.
Access Control: Door Define Quick Keys 9 1 4 2 Parameter Default Range RTE Button NO (normally open) NO/NC When pressed, this device sends a command to the door relay. 1. Press [4] and / to enter the door input settings. 2. Press [2] and / . 3. Toggle the / termination, as follows: key to select the appropriate RTE button NO: Sets the RTE button to normally open. NC: Sets the RTE button to normally closed. 4. Press 9 1 / . Door Label 5 Enables you to assign a door label. 1.
9 3 Access Control: Special Code The Special Code menu enables you to assign codes to the arm cards defined in the system in order to perform operations in addition to opening the doors (such as arming the system). Users can arm the system only after the Arm Code has been entered, as this code informs the system that its about to be armed.
0 Exit Programming The Exit Programming menu enables you to save any programming changes made during the current session. Important: Any changes you make to the programmed parameters are not saved until you exit the Installer Programming Menu correctly. ¾ To access the Exit Programming menu: 1. From the main Installer Programming menu, press [0], or press the / / or keys until you find the number [0] Exit Program option, shown below, and / then press .
/ Discard your changes by using the NO on the display and then press / key to change the [Y] YES to [N] . The following display appears: The keypad returns to the normal user display.
Chapter 6: Installer Programming Within the User Functions Mode This chapter describes the ProSYS programming options and functions located in the user’s programming menu that can also be accessed and programmed by an authorized installer after inserting a valid installer code.
3. Use the / key to obtain the relevant menu item or use the specified Quick Key combination and your installer code. For example, to access Overload Restore, press: [2][0][2][Installer Code] 2 / .
Activities Quick Keys Parameter Range Notes: 1. The outgoing call will always be executed trough the GSM channel. 2. Talking is not optional during the call. 3. This option can be used to get any provider information. The call can be established to any phone number. 4. When using this feature on a non full GSM/GPRS version module the outgoing call will be executed through the PSTN line (if connected to the panel).
View Quick Keys 3 Parameter Range Zone Status 4 This parameter displays all system zones and their current status. 3 Event Log 5 This parameter enables viewing the event log of significant system events including date and time. Note that the events log cannot be erased. Scroll down using the event log entries. / key to view the next Notes: 1. Press the / key to view the zone label. 2. Use the / key to move forward 10 events or the key to move backward 10 events.
Maintenance Quick Keys 4 Parameter Range Battery Test 2 This parameter tests the system’s standby batteries. 4 Diagnostics 9 This menu enables performing diagnostic tests for: [1] BUS Zones [2] Power Supply [3] Siren [4] GSM 4 More 0 The More menu provides additional parameters. 1. From the Maintenance menu, press [0] and press The following display appears. / . MAINTENANCE: 1)WALK TEST 2.
Maintenance Quick Keys 4 0 3 Parameter Range Get ACM IP View the ACM IP address. Required for establishing remote communication for U/D through the IP network. 4 0 4 Pre-paid SIM When using Pre-paid SIM cards use this menu to program the parameters to be able to receive information regarding the SIM card credit level [1] SMS Message: When performing manual Credit Level check this message will be sent to the provider in order to receive the SIM card credit.
2. Enter your installer code and press / . The following display appears. MISCELLANEOUS: 1) PRINTER CNTRL 3. From the Miscellaneous menu, press [4] to access Voice Message and press / . The following display appears. VOICE MESSAGE: 1)MSG. STRUCTURE 4. You are now in the Voice Message menu and can access the required submenus, as described in the following sections.
Maintenance: Voice Message Quick Keys 9 4 2 Parameter 1 Range Common Message 1. Press [1]. The following display appears: COMMON MSG: 1)PLAY 2. Press the required option as follows: Press [1] to play the common message. Press [2] to record a new message. The following display appears: PRESS # TO START MESSAGE RECORD Press / and speak your message into the microphone. The counter in the display counts down the seconds remaining until the recording will stop. PRESS # TO STOP REC.
Maintenance: Voice Message Quick Keys 9 4 2 Parameter 3 Range Zone Message 1. Press [2]. The following display appears: ZONE#:01 ZONE 001 (01-32) 2. Select the zone number and press / . 3. Press the required option as follows: Press [1] to play the zone message. Press [2] to record a new message. The following display appears: PRESS # TO START MESSAGE RECORD Press / and speak into the microphone. The counter in the display counts down the seconds remaining until the recording will stop.
Maintenance: Voice Message Quick Keys Parameter Range 4. Press the required option as follows: Press [1] to play the utility output message. Press [2] to record a new message. The following display appears: PRESS # TO START MESSAGE RECORD Press / and speak into the microphone. The counter in the display counts down the seconds remaining until the recording will stop. Recording stops automatically after 2 seconds. If you finish your message in less than 2 seconds press / to stop recording.
Appendix A: Technical Data Main Panel Input Power 16.5 Volts AC @ 40 Volt-Amps (VA) (via integral transformer) Current Consumption 60 mA, typical / 70 mA, maximum Rechargeable Standby Battery 12 Volts up to 17 Amp-Hours (AH), typical Power Outputs: Y Auxiliary Power 12 Volts DC @ 600 mA, maximum (from all AUX terminals) Y Bell/LS (External) Sounder Output Programmable Voltage (Utility) Output 12 Volts DC @ 900 mA, maximum Cabinet Dimensions 37.5 cm x 33 cm x 9.
Zone Expansion Module: 16-Zone Current Consumption 27 mA, typical / 45 mA, maximum Main Panel Connection 4-wire BUS, up to 300 m from Main Panel Dimensions 16.5 cm x 6.6 cm x 1.8 cm BUS Zone Expansion Module Current Consumption 20 mA, typical Main Panel Connection 4-wire BUS, up to 300 m from Main Panel Dimensions 10.5 cm x 6.6 cm x 1.8 cm Wireless Expansion Modules 8-/16-Zone Current Consumption 40 mA , maximum Frequency 868.6-868.7 MHz (narrowband operation in EU) or 433.
3A Switched Power Supply Expansion Module Input Power 16.5VAC @ 50VA (via 230VAC/16.5VAC/50Hz transformer). Rechargeable Standby Battery 12V Up To 21 Amp-Hours (AH) Power Outputs: Auxiliary Output: 3A @13VDC Bell/LS (External) Bell/LS (External) Sounder Output: 1.
Listen In/ Message Unit Input Power 8V DC to 14V DC Current Consumption Audio Signal 9 mA (standby) / 60 mA (active speaking - normal volume) / 130 mA (active speaking - full volume) Vin max = 2.5V pp / Vout max = 4V pp Dimensions 6.2 cm x 11.3 cm x 3.2 cm Voice Messages Module Input Power 12V DC Current Consumption 6mA typique / 26mA maximum Dimensions 6.6 cm x 6.6 cm x 1.8 cm Proximity Key Reader Input Power 13.
Appendix B: ProSYS Accessories Keypads Description ProSYS KL08 ProSYS KL16 ProSYS KCL ProSYS KCLP ProSYS KTAG ProSYS KP ProSYS KPP RP200KT 8-LED Keypad (LEDS and Keys text indication) 16-LED Keypad (LEDS and Keys text indication) LCD Keypad (LEDS and Keys text indication) Proximity LCD Keypad+ 2 key tags (LEDS and Keys text indication) Proximity key tags (x10) Touchscreen keypad Touchscreen keypad with proximity (13.56 MHz) Proximity tags for ProSYS KPP (13.
WL T6CO WL T6G WL T6GS WL T312 WisDom KWL Wirless CO Detector Wirless Glass Break Detector Wirless GAS Detector Wirless WatcHOUT Wirless Keypad Power Supply Expanders Description ProSYS 1.5APS ProSYS 1.5APSB 1.5 Power Supply (PCB only) 1.5 Power Supply inside medium Metal box + Tamper (RP296EPSPUKA) 1.
Event Log Expander Description ProSYS EL5 ProSYS EL9 Event log expander to 512 events Event log expander to 999 events Advanced Communication Module Description ACM AA01 ACM AB01 ACM (RS485 and Ethernet interface) + modem ACM (RS485 and Ethernet interface) GSM/GPRS Module Description AGM 128GSX AGM 128GSM Bus Full Version in metal box Bus GPRS Version(SMS/GPRS/Data) in Metal box Fast PSTN Modem 2400 BPS Description ProSYS MD2400 Fast PSTN external modem 2400 BPS IP/GSM Receiver Description
B-4 ProSYS Installation and Programming Manual
Appendix C: Report Codes This appendix provides descriptions of all the Report Codes sent to the Monitoring Station.
Report Code Programming for ADEMCO POINT (CONTACT) ID (0420) C-2 PROGRAMMED DIGITS ADEMCO CODE EVENT REPORTING EVENT (RECOMMENDED) 3A 31 32 33 34 35 36 37 38 39 4A 41 42 43 44 45 46 47 48 49 5A 51 52 53 54 55 56 57 58 59 6A 61 100 110 111 115 120 121 122 123 130 131 132 133 134 135 136 137 140 144 145 150 155 156 300 301 302 305 321 330 333 351 373 380 Medical Key Fire Alarm Smoke Fire Key Panic Key Duress Silent Alarm Audible Alarm Burglary Perimeter Interior 24 Hour Entry/Exit Day/Night Outdoor Tam
PROGRAMMED DIGITS ADEMCO CODE EVENT REPORTING EVENT (RECOMMENDED) 62 63 64 65 66 400 401 402 403 407 Arm/Disarm Out Of Window User Arm/Disarm (with User ID) User Arm/Disarm (Group No. + User ID) Auto Arm/Disarm Remote Arm/Disarm 67 68 69 7A 71 72 73 74 75 76 77 78 79 8A 81 84 85 86 87 --- 408 409 411 421 570 574 602 143 307 334 336 355 381 384 406 606 139 312 999 626 Quick Arm Keyswitch Arm/Disarm Callback Request False Security Code Zone Bypass Forced Arm Communication Test Exp.
Report Code Programming for SIA (0700) C-4 PROGRAMMED DIGITS SIA EVENT CODE EVENT 1E 1F 20 21 AR AT CJ BA AC Restoral AC Trouble Dummy Burglary Alarm 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 BC BH BJ BT BX CA CF CG CJ CK CL CP CS CZ FT DD DT ER ET FA FB FC FH FJ FT FU HA HH JA JL MH JO JT LB Burglary Cancelled Burglary Alarm Restore Burglary Trouble Restore Burglary Trouble Burglary Test Automatic Closing ('+ Area Number') Forced Closing
PROGRAMMED DIGITS SIA EVENT CODE EVENT 44 45 46 47 48 LD LR LS LT LX Local Programming Denied Phone Line Restoral Local Program Success Phone Line Trouble Local Programming Ended 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B MA MH MJ MT OA OC OG PT OJ OK OP OR OS OZ PA PH PJ PT QA QH QJ QT RB UR RP RR TA TR TX UA UB UH UJ UR UT Medical Alarm Medical Alarm Restore Medical Trouble Restore Medical Trouble Automatic Opening Cancel Report Open Ar
PROGRAMMED DIGITS SIA EVENT CODE EVENT 6C 6D 6E 6F 70 UU VR VT XH YM Untyped Zone Unbypass Printer Restore Printer Trouble RF Interference Restoral Dummy 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 84 85 86 87 XJ XQ XR XS XT YA YC YH YK YM YP YQ YR YS YT BZ BZ BV LF IA IR ZZ RF Receiver Tamper Restoral RF Interface Transmitter Battery Restoral RF Receiver Tamper Transmitter Battery Trouble Bell Trouble Receiver/Transmitter Communication Fail Bell Restoral Communication Restoral System (Tra
Appendix D: Event Log Messages This appendix provides descriptions of all the Event Log messages.
EVENT MESSAGE DESCRIPTION ARM D:P=X C=YY Group D on Partition X is armed by user YY ARM D:P=X WB=YY Group D on partition X is set by wireless keyfob YY ARM FAIL P=X Fail to Arm Partition X by Guard due to not ready zones ARM:P=X C=YY Partition X armed by user YY ARM:P=X WB=YY Partition X armed by wirelesskeyfob YY AUT TST FAIL Failure of zone self-test AUTO TEST OK Automatic zone self-test OK AUX RS PS=X Restore of Aux power on power supply ID=X AUX RS ZE=X Restore of S.
EVENT MESSAGE DESCRIPTION COM OK WBA=X Bus communication OK with the wireless keyfob module ID=X COMM OK SIREN=X Bus communication OK with siren ID=X COMM OK PS=X Bus communication restore with power supply expander ID=X COMM OK UO=X Bus communication restore with UO expander ID=X COMM OK Z=XXX Bus communication OK with BUS zone XXX COMM OK ZE=X Bus communication restore with zone expander ID=X COMM.
EVENT MESSAGE DESCRIPTION FAULT Z=XXX Trouble in zone XXX (TEOL zone or BUS zone input TEOL) FIRE Z=XXX Fire alarm in zone XXX FIRE KP=XX Fire alarm from keypad (ID=XX) (keys 3 & 4) FOIL Z=XXX Trouble in foil (Day) zone XXX FOIL OK Z=XXX Restore in foil (Day) zone XXX FORCED P=X Partition X is force armed FOUND Z=XXX Wireless zone found, zone XXX FUNC=XX C=YY Quick key function XX by user YY GSM:BATTERY OK GSM battery OK GSM:GPRS PW ERR Authentication password is incorrect GSM:GPRS PW
EVENT MESSAGE DESCRIPTION IR RESTORE Z=XXX Trouble restore in the IR channel of BUS zone XXX IR TROUBLE Z=XXX Trouble in the IR channel of BUS zone XXX JAMM.
EVENT MESSAGE DESCRIPTION NO COM AC=X Bus communication failure with Access Control module X NO COM ACM Bus communication failure with the ACM module NO COM KP=XX Bus communication failure with keypad ID=XX NO COM KR=XX Bus communication failure with Proximity Key Reader XX NO COM PRN=X Bus communication failure with the printer module X NO COM VOICE Bus communication failure with Advanced Voice module NO COM WBA=X Bus communication failure with the wireless keyfob module ID=X NO COMM PS=X
EVENT MESSAGE DESCRIPTION READER=XX SET Set reader XX criteria REMOTE PROG The system has been programmed from the UD software RESTORE Z=XXX Alarm restore in zone XXX RMT ARM:P=X Partition X armed from the UD software RMT DIS:P=X Partition X disarmed from the UD software RMT HOM:P=X Partition X armed in Stay mode from the UD software SELF FAIL Z=XXX BUS zone XXX has failed the Self Test SELF OK Z=XXX Self Test in BUS zone XXX has been restored SOAK FAIL Z=XXX Zone XXX has failed in the So
EVENT MESSAGE DESCRIPTION UO TRIG ZN=XXX A zone defined as “UO Trigger” has been activated WEAK BAT PS=X Weak battery indication joined by 3A SMPS X WEAK BAT RS PS=X Weak battery restore indication joined by 3A SMPS X X.Modem:Comm OK BUS communication OK with the external modem X.Modem:TAMPER Tamper alarm in external modem X.
Appendix E: Installer Programming Maps [1] System [11] Time Define [111] Ex/En Delay 1 [115] S. Aux Break [119] More [112] Ex/En Delay 2 [116] WL MOD. Times [1191] Phone Line Cut Delay Time [113] Bell Timeout [117] Z.
[2] Zones [21] One by One [22] Partitions/Group [23] Zone Type [23zz00] Not used [23zz08] I+Ex(Op)/En [23zz16] Special [23zz01] Ex/En1 [23zz09] I+En Follower [23zz17] Pulsed KSW [23zz02] Ex/En2 [23zz10] I+Instant [23zz18] Exit Termination [23zz03] Ex(Op)/En [23zz11] UO Trigger [23zz19] Latch KSW [23zz04] En Follower [23zz12] Day Zone [23zz20] EN.
[3] Utility Output [30] Nothing [31] System [3101] Bell Follow [3107] AC Loss Fol [3113] D Key Reader Comm [3102] No Tel Line [3108] Sensors Test [3114] Switch AUX [3103] Comm. Fail [3109] Voice Module [3115] GSM Error [3104] Trouble Follow [3110] Battery test [3116] GSM:PSTN Loss [3105] GND Pulse [3111] Bell Burglary [3117] GSM:Low Bat [3106] Low Bat.
[5] Dialer [51] Link Up [511] MS Link Up [512] U/D Phones [541] Access Code [542] ID Code [543] MS Lock [5501] MS Enable [5507] User Initiate [5513] Show Handshake [5502] FM Enable [5508] Callback U/D [5514] Audible Kissoff [5503] U/D Enable [5509] Autobatch [5515] UD GSM Enable [5504] Call Delay [5510] Answer Machine [5516] X.
[7] Accessories [71] Add/Delete module [711] Keypad [717] Printer Module [7194] Siren [712] Zone Expander [718] Access Control [7195] BUS Zones [713] Utility Output [719] More [7196] GSM [714] Power Supply [7191] Dig Key Reader [7197] X. Modem [715] Event Logging [7192] Advanced Digital Voice [716] WL Button [7193] ACM [811] WL Button Param [812] WL Button Allocation [821] Strobe Control [823] Strobe Arm SQK [826] Proximity Level [822] Strobe Blink [824] Siren LED [827] Bat.
Email [575] Email [5751] Mail IP Address [5754] Email Prefix [5752] Mail SMTP Port [5755] Email Domain [5753] Mail POP3 Port [5756] SMTP User Name [5757] SMTP Password [83] GSM [831] GSM Parameters [8311] GSM Mode [83111] GSM Backup [83112] GSM Only [83113] GSM Main [8212] GSM Times [83121] PSTN Lost [83122] GSM Lost [83123] SIM Expire Date [8313] Prefix [8313 1 to 2] PBX Prefix [8313 3 to 8] Prefix Constant [83139] Remove Prefix [83130] Add Prefix [8314] PIN Code [8315] GPRS [83151] APN Code [83152]
RISCO Group Limited Warranty RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product.
Contacting RISCO Group RISCO Group is committed to customer service and product support. You can contact us through our website www.riscogroup.com or as follows: United Kingdom Tel:+44-161-655-5500 technical@riscogroup.co.uk USA Tel: +1-631-719-4400 support-usa@riscogroup.com Italy Tel: +39-02-66590054 support@riscogroup.it Brazil Tel: +1-866-969-5111 support-br@riscogroup.com Spain Tel:+34-91-490-2133 support-es@riscogroup.com China Tel: +86-21-52-39-0066 support-cn@riscogroup.
