r AR-3000 audio recorder RS-232C Reference AR-3000 RS-232C © 2001 Reference version 1.0 c Unauthorized copying or reproduction of this manual in part or in whole is prohibited. 2001.
r - Contents Section1 1.1 If You Have Been Using the AR-2000............................................................................................. 1 Section2 2.1 Introduction ....................................................................................................................... 1 Setup About the RS-232C Interface .......................................................................................................... 1 2.1.1 Connector and Cable ................................
r LW Recorded Phrase Protect Mode .......................................................................................... 12 SP System Copy ........................................................................................................................ 13 PC Copy Phrase......................................................................................................................... 13 PD Delete Phrase ..................................................................................
r EQ Equalizer Settings............................................................................................................... 27 VT Input Volume Thru Settings .............................................................................................. 27 BO Busy Out Settings ............................................................................................................... 27 DO Display Parameter Settings .........................................................................
r CR Card Remaining Capacity Output ..................................................................................... 40 DC Display Contrast Setting Output....................................................................................... 40 DP Direct Playback Setting Output......................................................................................... 41 SM System Setting Output .......................................................................................................
r Section1 Introduction This manual explains how to control the AR-3000 using RS-232C. For details on the operation of the AR-3000 itself, refer to the AR-3000 owner's manual. This manual assumes that you have a basic understanding of computers. For explanations of computer terminology or operation, please refer to commercially available manuals. The contents of this manual are subject to change without notice. 1.
r 2.3 Setup Procedure Here is the procedure for setting up the external computer and the AR-3000. 1) Connections with the computer Use an RS-232C cable to connect the two devices. Refer to “2.4 Connections with the computer.” 2) Turn on the power for the AR-3000 and the computer 3) Computer settings Set the communication parameters. Refer to “2.5 Computer settings.” 4) AR-3000 settings Set the communication parameters. Refer to “2.6 AR-3000 settings.
r Baud Rate Settings Set the baud rate to the desired value. (Refer to owner's manual p.118) 1) Press the MODE button. 2) Rotate the SELECT knob to select “7.1 Baud rate.” 3) Press the SELECT knob. 4) Rotate the SELECT knob to select the baud rate. Baud rate = 4800, 9600, 19200, 38400 bps Select the same setting as on the computer. 5) Press the SELECT knob. Rotate the SELECT knob to select “Yes” Press the ENTER button to set the baud rate. 6) Press the MODE button.
r a. The command is sent from the computer to the AR-3000. b. If the command was received correctly, the AR-3000 will transmit its settings as the Setting output command. If the command was received incorrectly, the AR-3000 will transmit an ER command. c. If the output from the AR-3000 is received correctly, send an ACK command. This ACK may be omitted, and is not absolutely necessary. If not correctly, an ER command “ER:0;” can be sent to the AR-3000.
r 3.1.2 Command Format Commands (control signals) have several formats. Type 0: Those consisting only of a control code. ' ; ' etc. is not attached. These consist only of a control code. Example) ACK Type 1: Commands with no parameters These commands end in ' ; ' Example) stxST; Type 2: Commands with parameters. Command : parameter, parameter . . .
r Section4 Details of each Command 4.1 Commands Transmitted from the External Device (Computer) to the AR-3000 The following 5 types of command are transmitted from the external device to the AR-3000. “External” in these explanations refers to the computer. “AR” refers to the AR-3000. 1) Control (execute) commands These command signals cause the AR-3000 to operate; e.g., playback or record. The player functions use mostly these commands.
r 3) Setting commands These commands are used to set AR-3000 parameters from the external device. 4) Request commands This command causes the AR-3000 to output the status of its current settings. When a Request command is transmitted to the AR-3000, the AR-3000 will transmit the requested contents as the Setting output command. In this case, an ACK will not be returned. However for the AC and AQ commands, an ACK will be output. If the command was not correct, an ER command will be returned.
r = PL (PLay) Function: Playback start Syntax: stxPL; Note: If the playback phrase has not been specified, the minimum default value (normally A001) will be used. The phrases specified by the PA command will be played back consecutively.
r Recording Commands = AE ( Auto inc rEc start ) Function: Starting Time-stamped Recording Syntax: stxAE: **** , ** , ** , ** , ** , ** , * ,* , * ; a b c d e f g h i a year ( 1998 – 2050 ) b month ( 1 – 12 ) c day ( 1 – 31 ) d hour ( 0 – 23 ) e minutes ( 0 – 59 ) f second ( 0 – 59 ) g RDAC-Grade 0 Announce 1 Long 2 2 Long 1 3 Standard 4 High 5 S-High h RDAC-Mode 0 Linear 1 Mode 1 2 Mode 2 3 Mode 3 4 H – Linear I Recording Type 0 Mono 1 Stereo Example) stxAE:2001,3,1,8,59,0,0,1,0; Add a time stamp for “20
r = RM (Rec Mode) Function: Record ready mode Syntax: stxRM: **** , * , * , * , * , * , * ; a b c d e f g a Phrase number b RDAC-Grade 0 Announce 1 Long 2 2 Long 1 3 Standard 4 High 5 S-High c RDAC-Mode 0 Linear 1 Mode1 2 Mode2 3 Mode3 4 H-Linear d Recording type 0 Mono 1 Stereo e Trigger recording 0 Off 1 Low 2 Mid 3 High f Recording Source 0 LINE - IN 1 MIDI - IN 2 LINE + MIC - IN 3 DIGITAL - IN g Time base 0 192 1 240 Example) RM:A1,3,2,1,0,1,1; This sets as follows; phrase “A0001”, RDAC-Grade “STANDARD”
r 4.2.2 Editing Commands = DM (Delete Mode) Function: Enable execution of editing commands. Syntax: stxDM; Note: In order for editing commands to be executed, the DM command must be used to put the unit into Delete mode. For the communication protocol, refer to 4.1 2) Editing commands. Caution:When Delete mode is exited, the AR-3000 will automatically output a CC command. The AR-3000 automatically escapes from the Delete mode two minutes after the DM command is issued.
r = FM (ForMat) Function: Format Card Syntax: stxDM; stxFM: * , * , * ; a b c a Card in slot 0 Card in slot A 1 Card in slot B b Maximum number of phrase 0 250 1 500 2 1000 c Reserved ( 0 or 1 ) Example) FM:0,1,0; The card in slot A is formatted as follows; the maximum number of phrases “500”. Note: The type and capacity of the card is detected automatically. Use only cards which the AR-3000 is able to use.
r = SP (Setting coPy) Function: System copy Syntax: stxDM; stxSP; Note: This copies the settings of the card in slot A to the card in slot B. Phrase Editing = PC (Phrase Copy) Function: Copy phrase Syntax: stxDM; stxPC: **** , **** ; a b a Phrase number of the copy source b Phrase number of the copy destination Example) PC:A1,A3; This copies the contents of phrase “A0001” to phrase “A0003”.
r > PV (Phrase diVide for AR-3000) Function: Divide Phrase Syntax: stxDM; stxPV: ****,**H**M**S**F*S,*****,***** ; a b c d a Phrase number b divide time ( 0H0M0S0F0S - 23H59M59S**F9S ) c Write-destination Phrase number d Write-destination Phrase number Note: Only audio phrases can be specified. The number of digits for **F (frame) increases according to the value of MTC type.
r > RT (Recording - Type convert for AR-3000) Function: Recording - Type convert Syntax_1: (Stereo to Mono) stxDM; stxRT: 0,*****,***** ; a b c a Recording Type 0 Stereo to Mono b Source Phrase number c Write-destination Phrase number Syntax_2: (Stereo to Mono1 , Mono2) stxDM; stxRT: 1,*****,*****,*****; a b c d a Recording Type 1 Stereo to Mono1 , Mono2 b Source Phrase number c Write-destination Phrase number 1 d Write-destination Phrase number 2 Syntax_3: (Mono1 , Mono2 to Stereo) stxDM; stxRT: 2,*****,**
r 4.2.3 Setting Commands Card Settings = CV (Card Volume label) Function: Card name setting Syntax: stxCV: * ,“********”, ***** ; a b c a Card in slot 0 Card in slot A 1 Card in slot B b Card name (up to 8 characters) c Reserved (Only '0') Example) stxCV:0,“ABCDEFGH”, 0; This specifies a name of “ABCDEFGH” for the card in slot A. Pattern Phrase Settings < PU (Pattern phrase set Up for AR-2000) Function: Pattern Phrase settings Syntax: stxPU: **** , * , **** , **S* , .... , **** , **S* ; a b c d ....
r > PS (Pattern phrase Set up for AR-3000) Function: Pattern Phrase settings Syntax_1: (Sequence or Random 1) stxPS: **** , * ,*, *** ,*****,***, **S* , .... , *** ,*****,***, **S* ; a b c d e f g …. d e f g a Pattern Phrase number b Pattern Phrase Playback mode 0 Sequence 1 Random 1 c Researved (Only '0') d Playback Sequence e Phrase number to be played back f Playback Volume (10 – 100 : 10% - 100% ) g Delay Time (0S0 - 59S9) Syntax_2: (Random 2 or Random 3) stxPS: **** , * ,*, *** ,*****,***, **S* , ....
r Phrase Settings < SU (phrase Set Up for AR-2000) Function: Phrase settings Syntax: stxSU: **** , “***********” , *** , **S* , * , **M**S , * , **M**S , *** , * ; a b c d e f g h I j a Phrase number b Phrase name (up to 12 characters) c Playback Volume (10 - 100) d Delay Time (0S0 - 59S9) e Repeat Playback 0 OFF 1 ON f Repeat interval (0M0S - 59M59S) g Control Output 0 OFF 1 ON h Offset time of control output (0M0S - 59M59S) i Tempo (5 - 260) j Reserved (Only '0') Example) SU:A001,“ABCDEFGHIJK”,100,10S5,1,
r > PO (Phrase control Out set up for AR-3000) Function: Control Out settings Syntax: stxPO: **** , *,**M**S; a b c a Phrase number b Control Out 0 OFF 1 ON c Offset Time (0M0S - 59M59S) > PP (phrase Playback Point set up for AR-3000) Function: Playback Point settings Syntax: stxPP: **** , **H**M**S**F*S, **H**M**S**F*S; a b c a Phrase number b Start (0H0M0S0F0S - 23H59M59S**F9S) c End (0H0M0S0F0S - 23H59M59S**F9S) Note: The number of digits for **F (frame) increases according to the value of MTC type.
r > VM(phrase VoluMe set up for AR-3000) Function: play Volume settings Syntax: stxVM: ***** , ***; a b a Phrase number b Play Volume %(10 - 100) > FD (phrase FaDe set up for AR-3000) Function: Fade In and Fade Out settings Syntax: stxFD: ****,*,**S*,*,**S*; a b c d e a Phrase number b Fade In Type 0 OFF 1 Time 1 2 Time 2 3 Time 3 4 ( 0S1 - 59S9 ) c Fade In Time ( 0S1 - 59S9 ) * This parameter is ignored when fade out type is 0 to 3. Please send one value of 0S1-59S9.
r MIDI Settings = MS (Midi Set up) Function: MIDI settings Syntax: stxMS: * , ** , * , * , ** ; a b c d e a Card in slot 0 Card in slot A 1 Card in slot B b MIDI Receive Channel 0 (OFF) 17 (ALL) 1-16 (MIDI Channel) c MIDI OUT 0 (OUT) 1 (THRU) d MIDI Note Trigger 0 (Trigger) 1 (Gate) e Device ID (1 - 32) > ME (Midi sEt up for AR-3000) Function: MIDI settings Syntax: stxME: * , * , * , * , * ; a b c d e a Card in slot 0 Card in slot A 1 Card in slot B b MIDI Note On Velocity 0 (OFF) 1 (ON) c MIDI Panpot 0 (OF
r = NM (Note Map) Function: MIDI note map settings Syntax: stxNM: * , **** , ..... , **** ; a 2 .....
r System Settings = BR (Baud Rate) Function: Communication speed setting Syntax: stxBR: * , * ; a b a Card in slot 0 Card in slot A 1 Card in slot B b Baud rate 0 (4800) 1 (9600) 2 (19200) 3 (38400) Note: Even if you use this command to specify the communication speed of the card, that of the AR-3000 will not be changed. It can be changed by turning on again or by setting from the front panel of the AR-3000 itself.
r = DP (Direct Play) Function: Direct Playback setting Syntax: stxDP: * , **** , **** , .... , **** ; a b c .... q a Card in slot 0 Card in slot A 1 Card in slot B b - q Phrase number which you wish to assign to control input pin b (CH1) c (CH2) | q (CH16) Example) DP:0,A1,_,A3,A4,_,A16; The setting will be written to “Card A”, and the phrases will be assigned to the control Input pin as follows; A0001 to CH1,...,A0003 to CH3, A0004 to CH4,..., and A0016 to CH16.
r < SM (SysteM for AR-2000) Function: System settings Syntax: stxSM: * , * , * , * , * , * ; a b c d e f a Card in slot 0 Card in slot A 1 Card in slot B b Line Input select 0 Mute : Line Thru ON , Volume 0% 1 Mix : Line Thru ON , Volume 100% 2 OFF : Line Thru OFF c Channel Playback (Dual Mono mode) 0 OFF 1 ON d Control Input select 0 Normal playback : for Direct Playback 1 Last-In playback : for Direct Playback 2 Sequence playback : for Direct Playback 3 Program(Count) playback 4 Binary playback e Binary P
r d Binary Playback Trigger Settings Level 0 Off 1 On e Binary Playback Trigger Settings Edge 0 Off 1 On f The Method used for specifying the phrase ( Terminal Recording ) 0 Binary 1 1 Binary 2 > AL (ArLink setup for AR-3000) Function: AR-LINK setting Syntax: stxAL: * , * ; a b a Card in slot 0 Card in slot A 1 Card in slot B b AR-LINK Mode 0 Off 1 Master 2 Slave > DN (Dual moNo mode setup for AR-3000) Function: Dual Mono Mode setting Syntax: stxDN: * , * ; a b a Card in slot 0 Card in slot A 1 Card in slot
r > EQ (EQualizer setup for AR-3000) Function: Equalizer setting Syntax: stxEQ: * , * , *** , * , *** , * , **; a b c d e f g a Card in slot 0 Card in slot A 1 Card in slot B b Equaizer 0 Off 1 On c Equalizer Low Gain dB ( -12 - +12 ) d Equalizer Low Frequency 0 200Hz 1 400Hz e Equalizer High Gain dB ( -12 - +12 ) f Equalizer High Frequency 0 3kHz 1 6kHz g Equalizer Attenation dB( -12 - 0 ) > VT (input Volume Thru for AR-3000) Function: Input Volume Thru setting Syntax: stxVT: * , * ; a b a Card in slot 0 C
r > DO (Display Off parameter for AR-3000) Function: Display Parameter setting Syntax: stxDO: * , * , * , * ; a b c d a Card in slot 0 Card in slot A 1 Card in slot B b Display Sleep 0 Off 1 On c Sleep Time (0M30S - 59M59S) 4.2.4 Request Commands < 2Q (pattern phrase reQuest for AR-2000) Function: Pattern Phrase setting contents request Syntax: stx2Q: **** ; a a Pattern Phrase number Note: This is a request for when the phrase type is pattern phrase.
r = AQ (All reQuest) Function: Reset the Phrase Output Counter Syntax: stxAQ: * ; a a Card in slot 0 Card in slot A 1 Card in slot B 2 Note: This sets the Phrase Output Counter to the lowest-numbered phrase of the phrases registered in the card. Use this command before you wish to output the settings of all phrases by using the PQ command, for example when you confirm the initial settings.
r = LQ (dispLay contrast reQuest) Function: Display Contrast setting request Syntax: stxLQ; Note: refer to DC command = MQ (Memory reQuest) Function: Card remaining capacity request Syntax: stxMQ; Note: refer to CR command = NQ (Note map reQuest) Function: MIDI note map setting contents request Syntax: stxNQ: * ; a a Card in slot 0 Card in slot A 1 Card in slot B Note: refer to NM command < PQ (Phrase reQuest for AR-2000) Function1: Phrase setting contents request Syntax: stxPQ: **** ; a a Phrase numb
r > QQ (phrase reQuest for AR-3000) Function1: Phrase setting contents request Syntax: stxQQ: **** ; a a Phrase number Note: The phrase settings for the specified phrase number will be output. The value of the Phrase Output Counter (described below) will not change. (* refer to the RU command) Function2: If the phrase number is not specified as a parameter, the AR-3000 will output the phrase settings for automatically incremented phrase number by the Phrase Output Counter.
r = TQ (Time stamp reQuest ) Function1: Time Stamp request Syntax: stxTQ: ****; a a Phrase number 0 Card in slot A 1 Card in slot B Note: Output the recording start time information for the specified phrase. (Refer to 4.4.1 TI Command.) The AR-3000 outputs an ER command for phrases in which time Information is not recorded.
r 4.2.5 Reply Commands = ACK Function: Response to normal reception of a command Syntax: ACK (06H) = ER (ERror) Function: Reply to the AR-3000 when an error has occurred Syntax: stxER: * ; a a Error number 0 Send this command to the AR-3000 when the output of the AR-3000 could not be read (In the case of a request command, the AR-3000 will re-transmit the Setting output command.) 1 Send this command when the output of the AR-3000 for confirmation is incorrect in Delete mode.
r f Card ID (Created automatically) g Reserved Note: refer to CQ command Phrase Settings < PU (Pattern phrase set Up for AR-2000) Function: Pattern Phrase setting output Syntax: stxPU: **** , * , **** , **S* , .... , **** , **S* ; a b c d ....
r < SU (phrase Set Up for AR-2000) Function: Phrase setting output Syntax: stxSU: **** ,“***********”, * , * , * , * , *** , **S* , * , **M**S , * , **M**S, ***, *, *******; a b c d e f g h I j k l m n o a Phrase number b Phrase name (up to 12 characters) c Phrase type 0 Phrase 1 Pattern Phrase 2 MIDI Phrase 3 Song Phrase d RDAC-Grade 0 Announce 1 Long 2 2 Long 1 3 Standard 4 High 5 S-High e RDAC-Mode 0 Linear 1 Mode 1 2 Mode 2 3 Mode 3 4 H-Linear f Recording Type 0 Mono 1 Stereo g Playback Volume (10 - 100
r > RU (phRase set Up for AR-3000) Function: Phrase setting output Syntax: stxRU: ***,”*********”, *,*,*,*,***,**S*,*,*,**M**S,*,**M**S,*,**S*,*,**S*, a b c d ef g h ij k l m n o p q **H**M**S**F*S, **H**M**S**F*S,*,*, **H**M**S**F**S, **H**M**S**F**S,***,**** ; r s tu v w x y a Phrase number b Phrase name (up to 12 characters) c Phrase type 0 Phrase 1 Pattern Phrase 2 MIDI Phrase 3 Song Phrase d RDAC-Grade 0 Announce 1 Long 2 2 Long 1 3 Standard 4 High 5 S-High e RDAC-Mode 0 Linear 1 Mode 1 2 Mode 2 3 Mode
r n Fade In Type 0 OFF 1 Time 1 2 Time 2 3 Time 3 4 ( 0S1 - 59S9 ) o Fade In Time ( 0S1 - 59S9 ) p Fade Out Type 0 OFF 1 Time 1 2 Time 2 3 Time 3 4 ( 0S1 - 59S9 ) q Fade Out Time ( 0S1 - 59S9 ) r Start (0H0M0S0F0S - 23H59M59S**F9S) s End (0H0M0S0F0S - 23H59M59S**F9S) t Loop Play 0 (OFF) 1 (ON) u The number of loops 0 ENDLESS 1 1 | 99 99 - Loop play Off v Loop 1 position (0H0M0S0F0S - 23H59M59S**F9S) w Loop 2 position (0H0M0S0F0S - 23H59M59S**F9S) x Tempo (5 - 260) y Phrase size (unit: byte) Note: refer to
r MIDI Settings < MS (Midi Set up for AR-2000) Function: MIDI setting output Syntax: stxMS: * , ** , * , * , ** ; a b c d e a Card in slot 0 Card in slot A 1 Card in slot B b MIDI Receive Channel 0 OFF 17 ALL 1 – 16 MIDI Channel c MIDI OUT 0 OUT 1 THRU d MIDI Note Trigger 0 Trigger 1 Gate e Device ID ( 1 - 32 ) Note: refer to IQ command > ME (Midi sEt up for AR-3000) Function: MIDI setting output Syntax: stxME: * ,**** , * , * , ** , * , * , * , * , * , * , * , * , * ; a b c d e f g h i j k lm n a Card in
r h MIDI Expression 0 OFF 1 ON i MIDI Note Output 0 OFF 1 ON j MMC Mode 0 OFF 1 Master 2 Slave k Sync Source 0 Internal 1 MTC l Sync Out 0 Off 1 MTC m MTC Type 0 30 1 29N 2 29D 3 25 4 24 n MTC Error Level ( 0 - 10 ) Note: refer to JQ command = NM (Note Map) Function: MIDI note map setting output Syntax: stxNM: * , **** , ..... , **** ; a 2 ....
r System Settings = AC (ACtive) Function: Active sensing reply Syntax: stxAC: * , **** ; a b a Status of AR-3000 0 During playback 1 During recording 2 During recording pause 3 During playback pause b Phrase number Note: During Dual Mono Mode, this is output twice. refer to the 4.2.4 AC command = CE (Count play sEt up) Function: Program (Count) Playback setting output Syntax: stxCE: * , * , **** , **** , .... , **** ; a b c c ....
r = DP (Direct Play) Function: Direct Playback setting output Syntax: stxDP: * , **** , **** , .... , **** ; a b c .... q a Card in slot 0 Card in slot A 1 Card in slot B b - q Phrase number which you assigned to control input pin b CH1 c CH2 | q CH16 Note: For unused direct channels, “----” is output. “PLAY” will be output for the direct channel which plays back the phrase shown in the display.
r > SY (SYstem for AR-3000) Function: System setting output Syntax: stxSY: * , * , * , * , * , * , * , * , * , * , **S* , **S* , * , ** , * , ** , * , ** , * , * , * , * , * , **M**S ; a b c d e f g h i j k l m n o p q r s t u v w x a Card in slot 0 Card in slot A 1 Card in slot B b Control Input select 0 Direct playback 1 Program playback 2 Binary playback 3 Terminal REC c Direct playback 0 Normal playback 1 First-In playback 2 Last-In playback 3 Sequence playback d Binary Playback Trigger Settings Level 0
r s Input Volume Thru 0 Off 1 On t Busy Out - During Delay Time 0 Off 1 On u Busy Out - During Phrase Play 0 Off 1 On v Busy Out - During Repeat Int 0 Off 1 On w Display Sleep 0 Off 1 On x Display Sleep - Sleep Time ( 0M30S - 59M59S ) Note: refer to YQ command = TI( Time stamp Info.
r = CC (Card Condition) Function: Card insertion status output Syntax: stxCC: * , * ; a b a Status of card slot A 0 Not inserted 1 Inserted b Status of card slot B 0 Not inserted 1 Inserted Note: This is transmitted automatically when a card is inserted or removed. This also occurs automatically for verification after the Delete mode has been exited. = %% (%?) Function: Card operation progress status output When a card operation is performed, this tells what percent has been completed.
r Note: When operation is paused with the PE command, the AR-3000 outputs the elapsed time from the start of the phrase to the point where paused. The number of digits for **F (frame) increases according to the value of MTC type = AE ( Auto inc rEc start ) Function: Output the total number of phrases recorded on the card Syntax: stxAE: S**** ; a a the total number of phrases recorded on the card Note: 4.4.2 This is output when AR receives an AE command.
r 21 Unsupported card or Incorrect format. Please change cards or format card. 100 The AR-3000 received a “2Q” or “3Q” command even though the specified phrase was not a pattern phrase. 101 A “PQ” or “TQ” command is used to request output even after the setting information of the last phrase has been output. 102 The AR-3000 received an RE command even though it was not in record-ready mode. 202 There is no time information for the specified phrase. 300 The command is not compatible with the Dual Mono mode.
r Section5 Appendix 5.1 AR-3000 Commands List 5.1.
r DQ IQ LQ MQ NQ PQ SQ TQ UQ VR Direct playback reQuest mIdi set up reQuest dispLay contrast reQuest Memory reQuest Note map reQuest Phrase reQuest System reQuest Time stamp reQuest coUnt playback reQuest VeRsion # Reply Commands ER ERror ACK(06H) Xon(11H)/Xoff(13H) Direct playback setting contents request MIDI setting contents request Display contrast setting request Card remaining capacity request MIDI note map setting contents request Phrase setting contents request System setting contents request Tim
r 5.1.
r # Commands sent from the AR-3000 to the external device # Setting Output Commands # Phrase PS SS RU Settings Pattern phrase Set up Song phrase Set up phRase set Up Pattern phrase setting output Song phrase setting output Phrase setting output type2 type2 type2 # MIDI Settings ME Midi sEt up MIDI setting output type2 # System Settings SY SYstem System setting output type2 Caution1: STX(02H) is attached to top of the command, and some commands has parameters with it.
r 5.3 Sample Algorithms The following are some examples of processing algorithms. 5.3.1 Playing Back a Phrase *1 *2 Refer to the error number to determine the cause. Is the command format incorrect? “ACK” will be output if the AR-3000 correctly recognizes the command. Note: - You can check the operating status by transmitting the “ AC “ command. - You can stop playback by transmitting the “ ST “ command.
r 5.3.2 Recording ( Nomal Recording ) *1 Setting such as RDAC-Grade and RDAC-Mode are made by “ RM “ command parameters. Note: - You can check the operating status by transmitting the “ AC “ command. - You can stop recording by transmitting the “ ST “ command.
r 5.3.3 *1 Recording ( Time-Stamped Recording) Setting such as RDAC-Grade and RDAC-Mode are made by “ AE “ command parameters. Note: - You can check the operating status by transmitting the “ AC “ command.
r 5.3.4 Verifying the Parameters (Data Settings) of All Phrases Starting with the Lowest-Numbered Phrase *1 What is the Phrase Output Counter? The AR-3000 has an internal counter for phrase output. When a phrase is output, the phrase that corresponds to the AR-3000's counter will be output. The maximum value will be the highest phrase number of each card. This will be reset by the AQ command (to the lowest phrase number).
r 5.3.5 *1 *2 Deleting a Phrase The AR-3000 will return the same “ PD “ command for confirmation. By transmitting “stxER:1:” you can exit Delete mode.
