User Manual
Table Of Contents
- English Owner’s Manual
- Deutsch Bedienungsanleitung
- SICHERER BETRIEB DES GERÄTS
- Wichtige Hinweise
- Schritte vor der Inbetriebnahme
- Kurzbetriebsanweisung
- Beispielanschlüsse
- Bedienelemente und Anschlüsse
- Verschiedene Anwendungen
- Komfortable Funktionen
- Verwenden eines Ständers
- Anhang
- Français Mode d'emploi
- UTILISATION DE L’APPAREIL EN TOUTE SÉCURITÉ
- Remarques importantes
- Étapes à suivre avant la mise sous tension
- Guide des opérations simples
- Exemples de branchement
- Commandes et connecteurs
- Utilisations variées
- Fonctionnalités pratiques
- Annexe
- Italiano Manuale dell'utente
- UTILIZZO SICURO DELL’UNITÀ
- IMPORTANTE:
- Passaggi da eseguire prima dell’accensione
- Semplice guida operativa
- Collegamenti di esempio
- Controlli e connettori
- Applicazioni varie
- Funzioni utili
- Appendice
- Español Manual del usuario
- UTILIZACIÓN SEGURA DE LA UNIDAD
- Notas importantes
- Procedimiento a realizar antes de encender la unidad
- Guía de funcionamiento sencilla
- Ejemplo de conexiones
- Mandos y conectores
- Diversas aplicaciones
- Funciones prácticas
- Apéndice
- Português Manual do proprietário
- USO SEGURO DA UNIDADE
- Observações importantes
- Etapas a serem executadas antes de ligar
- Guia de funcionamento simples
- Exemplo de conexões
- Controles e conectores
- Várias aplicações
- Recursos práticos
- Apêndice
- Nederlands Gebruikershandleiding
- HET APPARAAT VEILIG GEBRUIKEN
- Belangrijke opmerkingen
- Uit te voeren handelingen vóór het starten
- Handleiding voor eenvoudige bediening
- Voorbeeld van aansluitingen
- Bedieningselementen en aansluitingen
- Meerdere toepassingen
- Handige functies
- Appendix
8
Simple Operation Guide
Powering up and producing sound
Set all volume
controls to “0.”
1.
Set the volume of each
channel to the middle
position.
Also adjust the volume of the connected equipment.
4.
Use the MASTER [VOLUME]
to adjust the volume.
5.
Switch on the
BA-330’s power.
3.
Connect your microphones, instruments, portable audio player,
or other equipment.
For details on connections, refer to “Example connections” (p. 9).
Make sure that the volume knobs of all connected devices are set to “0.”
Switch on power to the connected equipment.
2.
1.
2.
Turn on power to your various devices in the order specied. By turning on devices in the wrong order, you risk causing malfunction and/or damage to
speakers and other devices.
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn o the power on all devices before
making any connections.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some
sound when the power is switched on, but this is normal, and does not indicate a malfunction.
*
*
*
*
Applying an eect
Turn on the [EFFECT] switch
for the channels to which
you want to apply an eect.
1.
Turn the [EFFECT] knob
to adjust the type and
amount of eect.
2.
Adjusting the tone quality
Adjusting the tone of each channel
Turn the [TONE] knob of the channel
that you want to adjust.
Adjusting the high and low ranges
of the overall sound (Equalizer)
Use the [LOW] knob to boost or
cut the low-frequency range.
Use the [HIGH] knob to boost or
cut the high-frequency range.