Owner`s manual

Various Settings (Function Mode)
Deutsch Français Italiano Español Português NederlandsEnglishEnglish
Display Value Explanation
F08
1
,
2
Changing the Tuning Method (Stretch Tuning)
This setting changes the type of stretch tuning, a tuning method that is used specically for pianos, in which the high notes are tuned
slightly sharper and the low notes are tuned slightly atter.
Normally, you should use the “1” setting (standard tuning curve).
F0g
F10
1
(Sostenuto, Soft),
2
(Start/Stop),
3
(Intro/Ending),
4
(Variation),
5
(Fill-in),
6
(Leading Bass)
Changing How the Pedals Work
Here you can assign the functions of the center pedal (
F0g
) and left pedal (
F10
).
1
" Sostenuto pedal (
F0g
), soft pedal (
F10
)
2
" Same function as the [s (Start/Stop)] button
3
" Intro/Ending function on/o (same function as the [y(Intro/Ending)] button)
4
" Variation on/o (same function as the [x (Variation)] button)
5
" Fill-in
6
" Leading Bass function on/o
F11
Off
,
On
Specifying How the Bass Part Behaves (Leading Bass)
The function that sounds the lowest note of a ngered chord as the bass tone is called “Leading Bass.”
O " The bass part of the rhythm plays the root of the chord. For example, if you play the chord E-G-C (C major), the note
C is sounded as the bass.
On " The bass part plays the lowest note of the chord you play. If you play the chord E-G-C (C major), the note E is
sounded as the bass.
The Leading Bass feature is always on while Split is o.
F12
1
(Intelligent),
2
(Standard)
Chord Recognition When Split Is On
Sets how the unit recognizes rhythm chords while Split function (p. 2) is on.
Intelligent " Plays chords even when basic chord tones are missing, allowing you to generate chords with very simple keyboard
playing. For details on how to play chords, refer to “Chord Fingering List” at the end of this manual.
Standard " Normal chord recognition.
F13
Off
,
On
Preventing Doubled Notes When Connected to a Sequencer
(Local Control)
If a software synthesizer is connected to USB MIDI, turn this item “OFF.”
Since most software synthesizer have their Thru function turned on,
notes you play on the keyboard may be sounded in duplicate, or get
dropped. To prevent this, you can enable the “Local O” setting so that
the keyboard and internal sound generator will be disconnected.
F14
U.01
–
U.10
(USER 01–10)
N.01
–
N.gg
(USB 01–99)
Copying a Song (Copy Song)
A song that you recorded on this unit can be copied to a USB ash drive.
The copy-source song number is displayed; use the [-] [+] buttons to select the desired number, and press the [s] button to conrm
it.
The copy-destination song number is displayed; use the [-] [+] buttons to select the desired number, and press the [s] button to
conrm it.
F15
None
Connecting to a Wireless LAN (WPS Connection)
This lets you establish a WPS connection.
The display indicates “
Svr
”; press the [y] (cancel) button or the [s] (execute) button to cancel or connect.
F16
None
Connecting to a Wireless LAN (Ad-Hoc Connection)
This lets you establish an ad-hoc connection.
The display indicates “
Svr
”; press the [y] (cancel) button or the [s] (execute) button to cancel or connect.
F17
000
–
ggg
Viewing the Ad-Hoc Key
Of the ve-digit ad-hoc key, the lower three digits are shown (the upper two digits are 00).
Software
Synthesizer
Local Control
Sound Generator
USB MIDI
In
USB MIDI
Out
Computer
page 15
page 15
page 15
13