User Manual

Overall Settings
System Settings
Here you can make overall settings that apply to the entire
INTEGRA-7, such as those for tuning and MIDI message reception.
1. In the MENU screen, choose “SYSTEM” and press the
[ENTER] button
The SYSTEM screen will appear.
2. Select the item whose settings you want to edit.
3. Select the parameter that you want to edit, and edit its
value.
Saving the System Settings
System settings will return to their previous state when you turn
o the unit. If you want these settings to be retained even after the
unit is turned o, you must save the system settings.
1. In the SYSTEM screen, hold down the [SHIFT] button and
press the [EDIT] button.
A message will indicate “Completed!” and the settings will be saved.
NOTE
Never turn o the unit while data is being saved.
System Parameter
The operations of the system parameters are explained below,
organized according to the structure of the parameters.
Setup Settings (SETUP)
Parameter Value Explanation
LCD
Contrast
1–20 Adjusts the contrast of the display.
LCD
Brightness
1–20
Adjusts the brightness of the display.
The brightness will increase as the value is
raised.
Top Screen
TYPE1,
TYPE2
TYPE1: A screen that shows the tone of the
current part in large characters
TYPE2: A screen that shows the studio set
and tones
* You can also switch this by pressing [SHIFT]
+ [ENTER] in the top screen.
Auto O
OFF,
30 [min],
240 [min]
Species whether the unit will turn o
automatically after a certain time has elapsed.
(p. 55)
If you don’t want the unit to turn o automati-
cally, choose “OFF” setting.
USB Driver
VENDER
(MIDI+AUDIO),
GENERIC
(MIDI Only)
Species whether the INTEGRA-7 will use
the dedicated driver provided by Roland
(VENDER) or the standard driver provided by
the operating system (GENERIC) (p. 44).
If you choose GENERIC, USB operation is
limited to MIDI.
* This setting will take eect after you save
the settings and turn the unit o, then on
again.
Startup Settings (STARTUP)
Parameter Value Explanation
Startup
Studio Set
LAST-SET,
(Studio Set
number)
Species the studio set that will be loaded
when the unit is turned on.
If you want the most recently selected studio
set to be loaded, choose “LAST-SET.”
Startup
Expansion
SlotA–SlotD
OFF, (Sound
Library
name)
Species the sound library that will be loaded
into each RAM slot when the unit is turned on.
Volume and Pitch Settings (SOUND)
Parameter Value Explanation
Master
Level
0–127 Species the overall volume of the INTEGRA-7.
Master Tune
415.3–466.2
Hz
Species the overall tuning. The displayed
value is the frequency of the A4 note (middle
“A”).
Output Gain -12–+12 dB
Adjusts the output gain of the analog output
and digital output.
Master Key
Shift
-24–+24 Transposes the overall pitch in semitone steps.
Sampling
Rate
44.1, 48, 96
kHz
Species the audio sampling rate.
Ext Part
Source
Select
USB AUDIO,
INPUT
Selects the input source that will be assigned
to the Ext part.
Synchronization Settings (SYNC/TEMPO)
Parameter Value Explanation
Sync Mode
MASTER,
SLAVE
MASTER: Choose this setting when using the
INTEGRA-7 by itself.
SLAVE: Choose this setting if you want the
INTEGRA-7 to operate in synchronization with
the MIDI clock of an external device.
Clock
Source
MIDI, USB
If the Sync Mode is set to “SLAVE,” you
can specify whether the INTEGRA-7 will
synchronize with clock received at the MIDI IN
or with clock received at the USB port.
System
Tempo
20–250
Species the system tempo.
* If the Sync Mode is “SLAVE,” this tempo
value is ignored because the INTEGRA-7 will
synchronize to clock data received from an
external MIDI device.
Tempo
Assign
Source
SYSTEM,
STUDIO SET
Species whether the tempo will follow the
system setting (System Tempo) or the tempo
of each studio set (Studio Set Tempo).
48