User Manual

Overall Settings
Introduction Playing/Creating Sounds Use with a Computer Overall Settings Appendix
Quick Guide
MIDI Settings (MIDI)
Parameter Value Explanation
Device ID 17–32
When transmitting and receiving system
exclusive messages, the device ID numbers of
both devices must match.
Studio Set
Control
Channel
1–16, OFF
Species the MIDI receive channel on which
MIDI messages (program change/bank select)
from an external MIDI device will be received
by the INTEGRA-7 to switch studio sets.
Choose “OFF” setting if you don’t want studio
sets to be switched from a connected MIDI
device.
USB-MIDI
Thru
OFF, ON
Species whether MIDI messages received via
the USB COMPUTER port/MIDI IN connector
will be re-transmitted from the MIDI OUT
connector/USB COMPUTER port (ON) or not
be re-transmitted (OFF) (p. 45).
Tx Edit Data OFF, ON
When you edit tone or studio set settings,
this species whether your edits will be
transmitted as system exclusive messages
(ON) or not be transmitted (OFF).
Rx Program
Change
OFF, ON
Species whether program change messages
will be received (ON) or not be received (OFF).
Rx Bank
Select
OFF, ON
Species whether bank select messages will
be received (ON) or not be received (OFF).
Rx Exclusive OFF, ON
Species whether system exclusive messages
will be received (ON) or not be received (OFF).
Rx GM
System On
OFF, ON
Species whether GM System On messages
will be received (ON) or not be received (OFF).
Rx GM2
System On
OFF, ON
Species whether GM2 System On messages
will be received (ON) or not be received (OFF).
Rx GS Reset OFF, ON
Species whether GS Reset messages will be
received (ON) or not be received (OFF).
Motional Surround Settings (MOTIONAL SURROUND)
Parameter Value Explanation
2CH Out
Mode
SPEAKER,
PHONES
Species whether the two-channel surround
output will be processed appropriately for
listening through speakers (SPEAKER) or
headphones (PHONES).
5.1CH
Center SP
Switch
OFF, ON
Species whether sound will (ON) or will not
(OFF) be output from the front center speaker
of a 5.1 channel speaker system.
5.1CH Sub
Woofer
(LFE) Switch
OFF, ON
Species whether sound will (ON) or will not
(OFF) be output from the subwoofer of a 5.1
channel speaker system.
Preview Settings (PREVIEW)
Parameter Value Explanation
Preview
Mode
SINGLE,
CHORD,
PHRASE
SINGLE: The notes specied by Preview 1–4
Note Number will be sounded one at a time,
consecutively.
CHORD: The notes specied by Preview 1–4
Note Number will be sounded simultaneously.
PHRASE: The phrase provided for the
corresponding patch type (category) will be
played.
Preview
1–4 Note
Number
C-1–G9
Specify the pitches of the four notes that will
be sounded if you set the Preview Mode to
“SINGLE” or “CHORD.”
* These settings are ignored if Preview Mode
is set to “PHRASE.”
Preview 1–4
Velocity
OFF, 1–127
Specify the velocities of the four notes that
will be sounded if you set the Preview Mode
to “SINGLE” or “CHORD.”
* These settings are ignored if Preview Mode
is set to “PHRASE.”
Control Function Settings (CONTROL)
Parameter Value Explanation
System
Control
Src1–4
OFF,
CC01–31,
33–95,
PITCH BEND,
AFTER-
TOUCH
Specify the MIDI messages that will be used as
system controls.
System Control settings allow you to specify
MIDI messages that will apply in common to
the entire INTEGRA-7, and can be used for
controlling volume, tone, etc.
You can assign up to four MIDI messages for
this type of control.
If you want to make assignments for realtime
control of the sound and eects for each
tone independently, use “matrix control” or
“multi-eect control.”
For details, refer to the “Parameter Guide PDF.”
Control
Source
Select
SYSTEM,
STUDIO SET
SYSTEM: “System Control Src 1--4” will be
used for tone control.
STUDIO SET: Tone Control Src 1--4 (p. 32) of the
Studio Set will be used for tone control.
Viewing the System Version
Shows the INTEGRA-7’s software version.
1. In the MENU screen, choose “SYSTEM” and press the
[ENTER] button.
The SYSTEM screen will appear.
2. Use the cursor [ ] [ ] buttons to select the “VERSION”
tab.
49