Owner's Manual
MFX types and parameters
98
r
VIMA JM-5
36. Chorus‰ DLY
This effect connects a chorus and a delay in series.
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Chorus Depth (0~127)—Modulation intensity.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
37. Flanger‰ DLY
This effect connects a flanger and a delay in series.
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Flanger Depth (0~127)—Modulation intensity.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
38. CHO‰ Flanger
This effect connects a chorus and a flanger in series.
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Modulation frequency of the cho-
rus effect.
●
Chorus Depth (0~127)—Modulation intensity of the chorus
effect.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Modulation frequency of the
flanger effect.
●
Flanger Depth (0~127)—Modulation intensity of the flanger
effect.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Level (0~127)—Output level.
39. CHO/DLY
This effect connects a chorus and a delay in parallel. (“Parallel”
means that the input signal is processed by two effects that do
not interact.)
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Chorus Depth (0~127)—Modulation intensity.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
40. Flanger/DLY
This effect connects a flanger and a delay in parallel.
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Frequency, i.e. modulation speed.
●
Flanger Depth (0~127)—Modulation intensity.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Delay Time (0.0~500.0ms)—Adjusts the time until the delay is
heard.
●
Delay Feedback (–98%~0~98%)—Adjusts the amount of the
delay sound that’s fed back into the effect. Negative (–) settings
invert the phase.
●
Delay HF Damp (200~8000Hz, Bypass)—Adjusts the frequency
above which sound fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies, set this parameter
to BYPASS.
●
Delay Balance (D100:0W, D50:50W, D0:100W)—Adjusts the vol-
ume balance between the sound that is sent through the delay
(W) and the sound that is not sent through the delay (D).
●
Level (0~127)—Output level.
41. CHO/Flanger
This effect connects a chorus and a flanger in parallel.
●
Chorus Pre Delay (0.0~100.0ms)—Adjusts the delay between the
incoming direct signal and the moment when the chorus starts
working.
●
Chorus Rate (0.05~10.0Hz)—Modulation frequency of the cho-
rus effect.
●
Chorus Depth (0~127)—Modulation intensity of the chorus
effect.
●
Chorus Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the chorus sound (W).
●
Flanger Pre Delay (0.0~100.0ms)—Adjusts the delay time from
when the direct sound begins until the flanger sound is heard.
●
Flanger Rate (0.05~10.0Hz)—Modulation frequency of the
flanger effect.
●
Flanger Depth (0~127)—Modulation intensity of the flanger
effect.
●
Flanger Feedback (–98%~0~98%)—Adjusts the proportion of
the flanger sound that is fed back into the effect. Negative (–)
settings will invert the phase.
●
Flanger Balance (D100:0W, D50:50W, D0:100W)—Volume bal-
ance between the direct sound (D) and the flanger sound (W).
●
Level (0~127)—Output level.
JM-5_US.book Page 98 Tuesday, December 14, 2010 10:29 AM