Owner`s manual

103
Chapter 6 Making Original Patches
Chapter6
7. Press the [CURSOR (right/left)] buttons to move the
cursor below the tone number (T-1 to T-4) for which you
want to define the parameter.
8. Specify a value using the [VALUE] dial or the [INC/
DEC] buttons.
9. After the value is specified, press the [EXIT] button to
return to the previous screen.
Parameters that can be set
- MOD:
CONTROL1/2/3/4 DEST, CONTROL1/2/3/4 DEPTH
- BEND:
RANGE UP, RANGE DOWN, CONTROL1/2/3/4
DEST, CONTROL1/2/3/4 DEPTH
- AFT:
CONTROL1/2/3/4 DEST, CONTROL1/2/3/4 DEPTH
* See the following sections for descriptions of the setting ranges
and contents of the respective parameters.
Parameters common to CONTROL
MOD/BEND and CONTROL AFT
CONTROL1/2/3/4 DEST
These are the parameters that can be set up for MOD, BEND
and AFT, respectively.
Select the parameters that will be controlled when each
controller of the external MIDI device is operated. For each
controller, you can assign up to four parameters for each tone
(CONTROL 1 through CONTROL 4).
Range:
- OFF: No control
- PCH: Pitch control.
- CUT: refer to FILTER: CUTOFF (p. 92).
- RES: refer to FILTER: RESONANCE (p. 93).
- LEV: refer to AMP: TONE LEVEL (p. 95).
- PAN: refer to AMP: TONE PAN (p. 96).
- L1P: refer to LFO1/2: PITCH DEPTH (p. 99).
- L2P: refer to LFO1/2: PITCH DEPTH (p. 99).
- L1F: refer to LFO1/2: FILTER DEPTH (p. 99).
- L2F: refer to LFO1/2: FILTER DEPTH (p. 99).
- L1A: refer to LFO1/2: AMP DEPTH (p. 99).
- L2A: refer to LFO1/2: AMP DEPTH (p. 99).
- PL1: refer to LFO1/2: PAN DEPTH (p. 99).
- PL2: refer to LFO1/2: PAN DEPTH (p. 99).
- L1R: refer to LFO1/2: RATE (p. 98).
- L2R: refer to LFO1/2: RATE (p. 98).
CONTROL1/2/3/4 DEPTH
These are the parameters that can be set up for MOD, BEND
and AFT, respectively. Specifies the amount of change that
will occur for each parameter selected as a control
destination.
Range: -63– +63
With positive (+) settings, higher values will allow greater
control. With negative (-) settings, the direction of the change
will be inverted.
* Parameters that are modified using controllers are modified
only temporarily. The value of the parameter itself is not
directly changed.
CONTROL BEND parameters
BEND: RANGE
Bend Up/Down (Bend Range Up/Down)
Specifies the amount of pitch change (in semitone units) that
will occur when the pitch bend lever of an external MIDI
device is operated. You can make independent settings for
movement to the right (raising the pitch) and left (lowering
the pitch).
Range:
- Bend Range Up:0– +12
- Bend Range Down:0– -48
Higher settings will result in a greater pitch change when the
pitch bend lever is moved to the left or right.
For example, if Bend Range Up is set to “+12,” the pitch will
rise one octave when the pitch bend lever is moved to the
right-most position.
Setting example1
Using the modulation lever of an external MIDI keyboard to apply
vibrato (Example of using LFO1 and CONTROL1)
1. For each tone, set LFO1 PITCH DEPTH to "0"
➔ "LFO1/2: PITCH DEPTH": p. 98
2. Set LFO1 RATE to approximately "90"
➔ "LFO1/2: RATE": p. 98
3. For each tone, set CONTROL1 DEST to "L1P"
➔ "CONTROL 1/2/3/4 DEST": p. 103
4. For each tone, set CONTROL1 DEPTH to approximately "10"
➔ "CONTROL 1/2/3/4 DEPTH": p. 103
Setting example 2
Using the pitch bend lever of an external MIDI keyboard to change
the pan (Example of using CONTROL2)
1. For each tone, set Tone Pan to "0"
➔ "AMP: TONE PAN": p. 96
2. Set Bend Range Up/Down to "0"
➔ "BEND: RANGE": p. 103
3. For each tone, set CONTROL2 DEST to "PAN"
➔ "CONTROL 1/2/3/4 DEST": p. 103
4. For each tone, set CONTROL2 DEPTH to "63"
➔ "CONTROL 1/2/3/4 DEPTH": p. 103