Owner`s manual

* If you wish to restore the pattern to its original state, use
[INC] [DEC] or the [VALUE] dial to re-select the same
pattern. The next time that the pattern repeats, it will
return to its original settings.
* The resonance value will not increase beyond the value
specified by the Resonance Limiter.
☞ ÒSpecifying the Variable Range of Resonance
(Resonance Limiter)Ó (p. 164)
08:Cut+Reso2-S
(Cutoff + Resonance 2 Single)
Hand movement will modify the cutoff and resonance
of the current part.
As your hand comes closer to the controller, the cutoff
value will decrease, and the resonance value will
increase.
If your hand is outside of the effective range, the cutoff
value will be Ò127Ó and the resonance value will be
Ò0,Ó regardless of the location of your hand.
* If you wish to restore the pattern to its original state, use
[INC] [DEC] or the [VALUE] dial to re-select the same
pattern. The next time that the pattern repeats, it will
return to its original settings.
* The resonance value will not increase beyond the value
specified by the Resonance Limiter.
☞ ÒSpecifying the Variable Range of Resonance
(Resonance Limiter)Ó (p. 164)
09:Cut+Reso3-A
(Cutoff + Resonance 3 All)
Hand movement will modify the cutoff and resonance
of all parts.
The moment that your hand is placed over the con-
troller, the resonance will reach the maximum value,
and as your hand comes closer to the controller, the
cutoff value will increase.
If your hand leaves the effective range, the cutoff
value will be Ò127Ó regardless of the location of your
hand.
* If you wish to restore the pattern to its original state, use
[INC] [DEC] or the [VALUE] dial to re-select the same
pattern. The next time that the pattern repeats, it will
return to its original settings.
* The resonance value will not increase beyond the value
specified by the Resonance Limiter.
☞ ÒSpecifying the Variable Range of Resonance
(Resonance Limiter)Ó (p. 164)
10:Cut+Reso3-S
(Cutoff + Resonance 3 Single)
Hand movement will modify the cutoff and resonance
of the current part.
The moment that your hand is placed over the con-
troller, the resonance will reach the maximum value,
and as your hand comes closer to the controller, the
cutoff value will increase.
If your hand leaves the effective range, the cutoff
value will be Ò127Ó regardless of the location of your
hand.
* If you wish to restore the pattern to its original state, use
[INC] [DEC] or the [VALUE] dial to re-select the same
pattern. The next time that the pattern repeats, it will
return to its original settings.
* The resonance value will not increase beyond the value
specified by the Resonance Limiter.
☞ ÒSpecifying the Variable Range of Resonance
(Resonance Limiter)Ó (p. 164)
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Controlling a specific range
If you wish to use the DBeam Controller to control
only a specific range of cutoff or resonance, you can
use the Beam Range Lower and Upper System para-
meters to specify the lower and upper limits of the
variation. This will allow you to utilize the full valid
range of the DBeam Controller, so you can control the
tonal change with precision.
☞ ÒSpecifying How the DBeam Controller Will
FunctionÓ (p. 165)
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
11:Part Pan-A (Part Pan All)
Hand movement will modify the pan of all parts.
As your hand comes closer to the controller the pan
will move toward the right, and as your hand is taken
away from the controller the pan will move toward
the left.
If your hand leaves the effective range, the part pan
value will be Ò0Ó regardless of the location of your
hand.
* If you wish to restore the pattern to its original state, use
[INC] [DEC] or the [VALUE] dial to re-select the same
pattern. The next time that the pattern repeats, it will
return to its original settings.
Chapter 9. Using the DBeam Controller to Apply Various Effects
123
9