Owner`s manual

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
* Ties cannot be input.
* If you record the rhythm part in real time, and then use
Step Recording 2, the previously input notes can be
viewed on the front panel. However, you will see only
those notes that coincide with grid locations of the cur-
rently selected scale.
Also, if you change the scale during recording, notes
that had until then been visible may no longer be
shown on the front panel.
For example, if you input 32nd notes and then change
the scale to 16th notes, any notes that had been input
at keyboard pad locations 2, 4, 6, 8, 10, 12, 14 or 16 will
not be displayed.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Individually Editing Musical
Data (Microscope Edit)
By using Microscope Edit, individual data events can
be moved to a different location or edited in detail,
and you can also delete or insert individual notes, etc.
During step recording, you can switch to the
Microscope page at any time.
fig.10-56TEXT
1. Move from the Step Recording page to the
Microscope page.
While Recording in Step Recording 1 -> Press [REC].
While Recording in Step Recording 2 -> Press [PLAY].
You will enter the Microscope page, and the display
will indicate the current input location (measure, beat,
clock). This is referred to as the Òposition.Ó
fig.10-57
View the Musical Data That You
Input
Rotate the [VALUE] dial to move the position to a
location where musical data (notes and controller data,
etc.) was input. The display will show the position and
the type of musical data.
Rotating the [VALUE] clockwise will successively dis-
play the musical data that is located in the direction of
the pattern playback.
Rotating the [VALUE] dial counterclockwise will suc-
cessively display the musical data that is located in the
opposite direction of the pattern playback.
You can also use [FWD] and [BWD] to step through
the musical data instead of using the [VALUE] dial.
By holding down [SHIFT] and rotating the [VALUE]
dial, you can move the position in units of one clock.
* If two or more MIDI messages exist at the same position,
an Ò*Ó will appear in the upper left of the display.
fig.10-58TEXT
At this time you can press the PART button of another
part to view the recorded data of that part or change
the recording part. If you select the rhythm part, you
can also select rhythm tones.
2. To return to recording mode,
To Return to Step Recording 1 -> Press [REC].
To Return to Step Recording 2 -> Press [PLAY].
In the case of Step Recording 1, recording will resume
from the position to which you moved.
3. To exit the Microscope page, press [STOP].
If you wish to save the modified pattern, use the
Pattern Write operation.
☞ ÒSaving Patterns You've Modified (Pattern
Write)Ó (p. 26)
CURRENT NEXT
CURRENT NEXT CURRENT NEXT
E4
C4D3
G4
96 clocks=
Current position
Next position
Next position
measure 1
beat 1
clock 24
measure 1
beat 1
clock 85
measure 1
beat 2
clock 30
REC
NEXT
CURRENT
PLAY
Delete Insert Modify
Chapter 10. Recording Patterns
140
0