Owner`s manual

Range: OFF, ON
* When the arpeggiator is on, messages received at MIDI
IN will not be re-transmitted from MIDI OUT even if
this Thru setting is ON.
Specifying the Reception Status
for Each Part (MIDI Rx Switch)
For each part [R]Ð[7], you can specify whether or not
MIDI messages from MIDI IN will be received.
Use [PART SELECT] and the PART buttons to select
the part whose setting you wish to change.
Range: OFF (-), ON (+)
If this is ÒOFF,Ó the corresponding part cannot be
played from an external MIDI device.
Disconnecting the Keyboard
Pads from the Internal Sound
Generator (Local Tx Switch)
You can specify how MIDI messages from the con-
troller section (the keyboard pad and knobs, sliders,
DBeam Controller pedals etc.) will be sent to each part
[R]Ð[7].
Use [PART SELECT] and the PART buttons to select
the part whose setting you wish to modify.
Range:
INT (I): Messages from the controller section will
be transmitted only to the internal sound
generator.
EXT (E): Messages from the controller section will
be transmitted only to MIDI OUT.
BOTH (B): Messages from the controller section will
be transmitted both to the internal sound
generator and to MIDI OUT.
Normally you will leave this set at ÒBOTH.Ó
If you do not want messages from the controller sec-
tion to be transmitted from MIDI OUT, select ÒINT.Ó
If you want to use the controller section to control only
the external sound generator, select ÒEXT.Ó
Specifying the Channel That Will
Control Arpeggios
(Arpeggio Control Channel)
This specifies the channel that note messages arriving
from an external MIDI device need to be using in
order to control the arpeggios when the Remote
Keyboard Switch is ÒOFF.Ó
Range: OFF, 1Ð16
When note messages on the specified channel are
received from an external device, an arpeggio will be
generated based on those notes, and played by the
current part.
With the factory settings this is set at Ò16.Ó
☞ ÒUsing an External MIDI Keyboard to play
RPS or ArpeggiosÓ (p. 172)
* If the Remote Keyboard Switch is ÒON,Ó you can play
arpeggios on the current part simply by turning the
arpeggiator on.
Specifying the Channel That Will
Control RPS
(RPS Control Channel)
This specifies the channel that note messages arriving
from an external MIDI device need to be using in
order to control RPS when the Remote Keyboard
Switch is ÒOFF.Ó
Range: OFF, 1Ð16
When note messages on the specified channel are
received from an external device, RPS will play.
With the factory settings this is set at Ò15.Ó
☞ ÒUsing an External MIDI Keyboard to play
RPS or ArpeggiosÓ (p. 172)
* If the Remote Keyboard Switch is ÒON,Ó this setting is
ignored.
Specifying How Knob Data Is
Transmitted
(Edit Transmit/Receive Mode)
This specifies the type of MIDI message that will be
used to communicate with external devices when the
front panel knobs/sliders are moved while the [TONE
SELECT] indicator is dark.
* If a front panel knob/slider is moved while the [TONE
SELECT] indicator is lit, the corresponding setting will
be transmitted as a system exclusive message for each
tone. In the same way, the data from the knobs of the
REVERB section, DELAY section and EFX section will
also be transmitted as system exclusive messages, regard-
less of the mode.
Range: MODE1, MODE2
MODE1: Knob/slider data will be transmitted and
received as control changes and as system
exclusive data.
MODE2: Knob/slider data will be transmitted and
received as control changes.
With the factory settings this is set to ÒMODE1.Ó
169
Chapter 15. Configuration (System)
15