Owner`s manual

❍ Effect 1 (Reverb Send Level) (Controller number 91)
status 2nd byte 3rd byte
BnH 5BH vvH
❍ Effect 4 (Reverb Send Level)(Controller number 94)
status 2nd byte 3rd byte
BnH 5EH vvH
❍ RPN MSB/LSB (Controller number 100,101)
status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
<<< RPN >>
Control Changes include RPN (Registered Parameter Numbers), which are extended para-
meters whose function is defined in the MIDI specification.
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
order) is transmitted to specify the parameter you wish to control. Then, Data Entry mes-
sages (Controller numbers 6 and 38) are used to set the value of the specified parameter.
Once a RPN parameter has been specified, all further Data Entry messages on that channel
are considered to apply to that specified parameter. In order to prevent accidents, when the
desired setting has been made for the parameter, it is recommended that RPN be set to
Null.
This device receives the following RPNs.
RPN Data entry
MSB LSB MSB LSB Notes
00H 00H mmH Ñ Pitch Bend Sensitivity
mm : 00HÐ0CH (0Ð12 semitones)
ll : ignored (processed as 00H)
Up to 1 octave can be specified in semitone steps.
* The Bend Range up parameter, Bend Range Down parameter
will also be changed.
* Not received by the Rhythm Part.
00H 01H mmH llH Master Fine Tuning
mm, ll: 20 00HÐ40 00HÐ60 00H ( -8192 *50 / 8192Ð0Ð+8192 * 50
/ 8192 cent )
* The Fine Tune parameter of each Part will change.
00H 02H mmH Ñ Master Coarse Tuning
mm : 10HÐ40HÐ70H (-48Ð0Ð+48 semitones)
ll : ignored (processed as 00H)
* The Coarse Tune parameter of each Part will change.
7FH 7FH Ñ Ñ RPN null
RPN and NRPN will be set as ÒunspecifiedÓ. Once this setting
has been made, subsequent Data Entry messages will be
ignored. (It is not necessary to transmit Data Entry for RPN
Null settings.
Parameter values that were previously set will not change.
mm, ll: ignored
● Program Change
status 2nd byte
CnH ppH
pp=Program number: 00HÐ7FH (prog.1Ðprog.128)
* Not received when the Rx Program Change parameter is OFF.
* Not received when the Rx SW parameter is OFF.
● Channel Aftertouch
status 2nd byte
DnH vvH
* Not received when the Rx SW parameter is OFF.
● Pitch Bend Change
status 2nd byte 3rd byte
EnH llH mmH
mm,ll=Pitch Bend value: 00 00HÐ40 00HÐ7F 7FH (-8192Ð0Ð+8191)
* Not received when the Rx SW parameter is OFF.
■ Channel Mode messages
● All Sound Off (Controller number 120)
status 2nd byte 3rd byte
BnH 78H 00H
* When this message is received, all notes currently sounding on the corresponding chan-
nel will be turned off.
* Not received when the Rx SW parameter is OFF.
● Reset All Controllers (Controller number 121)
status 2nd byte 3rd byte
BnH 79H 00H
* Not received when the Rx SW parameter is OFF.
* When this message is received, the following controllers will be set to their reset values.
Controller Reset value
Pitch Bend Change ±0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath type 0 (minimum)
Expression 127 (maximum)
However the controller will be at minimum.
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN Unset. Previously set data will not change.
NRPN Unset. Previously set data will not change.
System General purpose controller 1 0 (minimum)
System General purpose controller 2 0 (minimum)
● All Note Off (Controller number 123)
status 2nd byte 3rd byte
BnH 7BH 00H
* When All Note Off is received, all currently sounding notes of the corresponding chan-
nel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held
until these are turned off.
* Not received when the Rx SW parameter is OFF.
● Omni Off (Controller number 124)
status 2nd byte 3rd byte
BnH 7CH 00H
* The same processing as when All Note Off is received will be done.
* Not received when the Rx SW parameter is OFF.
● Omni On (Controller number 125)
status 2nd byte 3rd byte
BnH 7DH 00H
* The same processing as when All Note Off is received will be done. The instrument will
not be set to OMNI ON.
* Not received when the Rx SW parameter is OFF.
● Mono (Controller number 126)
status 2nd byte 3rd byte
BnH 7EH mmH
mm=Mono number: 00HÐ10H (0Ð16)
* The same processing as when All Note Off is received will be done, and the Key Assign
parameter will be set to SOLO.
* Not received when the Rx SW parameter is OFF.
● Poly (Controller number 127)
status 2nd byte 3rd byte
BnH 7FH 00H
* The same processing as when All Note Off is received will be done, and the Key Assign
parameter will be set to POLY.
* Not received when the Rx SW parameter is OFF.
235