Owner`s manual

Available Settings:
ROM1 (Room 1): Reverb with short decay and high-
density.
ROM2 (Room 2): Reverb with short decay and low
density.
STG1 (Stage 1): Reverb with much lingering rever-
beration.
STG2 (Stage 2): Reverb with strong early reflec-
tions.
HAL1 (Hall 1): Clear-sounding reverb.
HAL2 (Hall 2): Rich-sounding reverb.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Reverb on/off
Hold down [EFFECT SELECT] and press [PRESET] to
switch reverb on/off.
When reverb is off, the following display will appear.
fig.4-3
This setting cannot be stored in a pattern.
●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●
Adjusting the Length of
Reverberation (Reverb Time)
You can adjust the time over which the reverberation
will continue.
1. Make sure that the [FUNC] indicator is
dark.
If it is blinking, press the button to make it go dark.
2. Press [EFFECT SELECT] several times to make
the top indicator light.
3. Rotate the [REVERB TIME] knob to set the
reverb time.
fig.4-4
Range: 0Ð127
Rotating the knob clockwise will lengthen the reverb
time. Rotating the knob counterclockwise will shorten
the reverb time.
Adjusting the Tone of the
Reverberation (HF Damp)
Specifies the frequency at which the high frequency
portions of the reverberation will be cut.
1. Make sure that the [FUNC] indicator is dark.
If it is blinking, press the button to make it go dark.
2. Press [EFFECT SELECT] several times to make
the middle indicator light.
3. Rotate the [HF DAMP] knob to set HF
Damp.
fig.4-5
Range: 200Ð8000 (Hz), BYPASS
Lowering this setting will cause more of the upper fre-
quency content to be cut, making the reverberation
more muted in tone.
If you do not wish to cut the high frequency range,
rotate the knob fully right to select ÒBYPASS.Ó
Adjusting the Overall Reverb
Volume (Reverb Level)
You can adjust the overall volume of reverb for the
eight parts (rhythm part and parts 1Ð7).
1. Press [FUNC] to make the indicator blink.
2. Rotate the [REV LEVEL] knob to adjust the
Reverb Level.
fig.4-6
Range: 0Ð127
Rotating the knob clockwise will increase the reverb
volume. Rotating the knob counterclockwise will
decrease the reverb volume.
Adjusting the Reverb Volume for
Each Part (Part Reverb Level)
You can adjust the reverb volume for each part.
REVERB
REVERB LEVEL
EFX REVERB LEVEL
HF DAMP
REVERB TIME
FUNC
REVERB
REVERB LEVEL
EFX REVERB LEVEL
HF DAMP
REVERB TIME
FUNC
REVERB
REVERB LEVEL
EFX REVERB LEVEL
HF DAMP
REVERB TIME
FUNC
Chapter 4. Applying Effects to the Sound (Effects)
80
4