VH-11_e 1 ページ 2005年4月12日 火曜日 午後1時20分 Owner’s Manual We’d like to take a moment to thank you for purchasing the Roland V-Hi-Hat VH-11. When using the VH-11, you will need to make the settings for the sound module. Refer to p. 6 or p. 8. fig.Structure * Hi-hat stand is not included. For details on compatible stands, refer to p. 9. 201a 03893278 Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 2; p. 3).
VH-11_e 2 ページ 2005年4月12日 火曜日 午後1時20分 USING THE UNIT SAFELY The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.
VH-11_e 3 ページ 2005年4月12日 火曜日 午後1時20分 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 558d • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. • This instrument is designed to minimize the extraneous sounds produced when it’s played.
VH-11_e 4 ページ 2005年4月12日 火曜日 午後1時20分 Getting Started Features Similar Touch and Feel as with an Acoustic Hi-Hat The VH-11 is constructed with one floating cymbal, making it compatible with commercially available hi-hat stands and providing the same feel as you get from an acoustic hi-hat, including the stick rebound, the looseness of the cymbal when you strike it, and the vertical action of the cymbal when you press and release the pedal.
VH-11_e 5 ページ 2005年4月12日 火曜日 午後1時20分 Mounting on the Hi-Hat Stand 1. Remove the clutch included with the hi-hat stand from the cymbal rod. * The clutch included with the hi-hat stand will not be used. * It is not necessary to remove the felt (or rubber) pad on the hihat stand used for supporting the bottom cymbal. 2. Confirm that the cymbal rod is firmly secured. fig.Assy.
VH-11_e 6 ページ 2005年4月12日 火曜日 午後1時20分 Connecting and Adjusting Connecting to a Sound Module Adjusting the Sound Module TD-12 and VH-11’s Offset 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 1. Connect the VH-11’s TRIGGER OUT jack to the sound module’s TRIGGER INPUT HI-HAT jack, and the VH-11’s CONTROL OUT jack to the sound module’s HH CTRL jack.
VH-11_e 7 ページ 2005年4月12日 火曜日 午後1時20分 Connecting and Adjusting 7. Press the [F3 (HI-HAT)] button. The “TRIGGER HI-HAT” screen appears. fig.TrigHH-12 Adjusting the Hi-Hat 1. Adjust the gap between the metal portion in the center of the lower hi-hat and the sensor’s center tip to a clearance of approximately 3 mm, then tighten the clutch screw. 8. Confirm the TD-12’s settings. Parameter Hi-Hat Type CC Max CC Resolution fig.HH-Adjust.e Value VH11/FD 90 NORMAL 9.
VH-11_e 8 ページ 2005年4月12日 火曜日 午後1時20分 Adjusting the Other Sound Module and VH-11’s Offset Using the TD-20 * If “VH11” is available as a Trigger Type setting on the TD-20 you are using, follow the instructions in Using the TD-12 (p. 6) to set the TD-20 and adjust the VH-11’s offset. 1. Confirm that the VH-11 and TD-20 are connected properly. 2. After making the hi-hat settings, release your foot from the pedal, and while keeping your foot off the pedal, turn on the power to the TD-20.
VH-11_e 9 ページ 2005年4月12日 火曜日 午後1時20分 Playing Methods Open/Closed The hi-hat tone changes smoothly and continuously from open to closed in response to how far the pedal is pressed. You can also play the foot closed sound (playing the hi-hat with the pedal completely pressed down) and foot splash sound (playing the hi-hat with the pedal fully pressed and then instantly opening it). Edge Shot This playing method involves striking the edge of the hi-hat with the shoulder of the stick.
VH-11_e 10 ページ 2005年4月12日 火曜日 午後1時20分 Troubleshooting No sound is heard Unable to control opening and closing Is the TRIGGER OUT connected to the sound module’s HH CTRL jack? Have you adjusted the VH-11’s offset? Connect the VH-11’s TRIGGER OUT jack to the sound module’s HI-HAT jack, and the CONTROL OUT to the sound module’s HH CTRL (p. 6).
VH-11_e 11 ページ 2005年4月12日 火曜日 午後1時20分 If the Clutch Was Apart from the Hi-Hat If the hi-hat clutch is inadvertently removed from the hi-hat, use the following procedure to reassemble and attach the clutch. Hi-Hat Being Properly Assembled fig.HH-Assy2.e Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-11. Be sure to use the special VH-11 clutch. Player Side The screw being in this direction fig.HH-Assy1.
VH-11_e 12 ページ 2005年4月12日 Information AFRICA EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SOUTH AFRICA That Other Music Shop(PTY)Ltd. 11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA TEL: (011) 403 4105 FAX: (011) 403 1234 Paul Bothner(PTY)Ltd.