Owner's manual

27
Creating Phrases
Editing the Steps
You can edit the length, velocity and other aspects of the notes you
inputted for each step.
1. Follow the steps in “Selecting a Clip” (p. 19) to select the
clip you want to edit.
* If the track type is “drum kit,” switch the pads to Note mode and press pads
[1]–[16] to select the drum instruments.
2. Press the [EDIT] button, and then press the STEP SEQUENCER
[1]–[16] buttons to select the steps to edit.
The step edit screen appears.
3. Use the [VALUE] dial to display the parameter you want
to adjust, and use the [CTRL 1]–[CTRL 3] knobs to edit the
values.
Track type: Tone
* You can input notes while you are editing steps by pressing the pads.
Parameter Explanation
NUM
If multiple notes have been inputted for a step, use the [VALUE] dial to
select the number and switch to the note to edit.
NOTE Changes the note.
LEN
Species the length of the note. You can’t extend a note past another
instance of the same note that occurs later.
VEL Adjusts the note velocity.
STA Adjusts the timing at which the note begins.
SUB
Sets the sub step. For instance, when this is set to “1/2,” one step plays
twice.
Track type: Drum Track
Parameter Explanation
VEL Adjusts the note velocity.
STA Adjusts the timing at which the note begins.
SUB
Sets the sub step. For instance, when this is set to “1/2,” one step plays
twice.
MTE
Adjusts the probability that a note sounds. With a setting of 0, the note
sounds each time; higher values decrease the probability that the note
sounds.
LEN
Species the length of the note. You can’t extend a note past another
instance of the same note that occurs later.
Making Measure-Related Settings
Use these settings to set the clip length, the length of a note in a single
step and so on.
1. Follow the steps in “Selecting a Clip” (p. 19) to select the
clip you want to edit.
2. Press the [EDIT] button, and then press the MEASURE [<] or
[>] buttons.
The MEAS EDIT screen appears.
3. Use the [VALUE] dial to select a parameter, and edit the value.
Parameter Value Explanation
Step Length 1–128 Species the length of the clip in number of steps.
Scale
Species the length of one note for each step.
1/8 Eighth note
1/16 Sixteenth note
1/32 Thirty-second note
1/4T Quarter-note triplet
1/8T Eighth-note triplet
1/16T Sixteenth-note triplet
Mode
Species how the clip plays back.
FWD Plays forward from the rst step.
REV Plays backward from the last step.
FWD+REV
Plays forward from the rst step, and plays backward
after reaching the last step.
INV
Switches to playing (inverts) the even-numbered and
odd-numbered steps.
RND Plays steps randomly.
Shue -50– +50 Species the amount of shue (bounce).
MEMO
You can also set these parameters in the CLIP SETTING screen.
&“Editing a Clip’s Settings” (p. 19)
Setting the Tempo and Metronome
These settings relate to the song’s tempo, the count-in for recording
and the metronome.
1. Press the [SEQ] button to set the workow to “Sequencer.”
2. Hold down the [SHIFT] button and press the [SEQ] button.
The TEMPO screen appears.
3. Use the [VALUE] dial to select the parameter that you want to
edit, and edit the value.
Parameter Value Explanation
BPM 40.0–300.0 Species the tempo of the overall project.
Count-in ON, OFF
Turns the count-in on/o. When this is on, a one-
measure count-in plays before recording begins.
Metronome ON, OFF Turns the metronome on/o.
Metro Level 1–127 Adjusts the metronome’s volume.
Metro Type TYPE1–9 Adjusts the metronome’s sound.