Reference Manual
Table Of Contents
- Rosemount 1408H Level Transmitter
- Contents
- 1 Introduction
- 2 Transmitter overview
- 3 Mechanical installation
- 3.1 Safety messages
- 3.2 Installation considerations
- 3.3 Mounting preparations
- 3.4 Mount transmitter on tank
- 4 Electrical installation
- 5 Configuration
- 6 Operation and maintenance
- 7 Service and troubleshooting
- 7.1 Safety messages
- 7.2 Diagnostic messages
- 7.2.1 Device hardware fault – Device exchange
- 7.2.2 General power supply fault – Check availability
- 7.2.3 Device software fault – Check firmware revision
- 7.2.4 Parameter error – Check data sheet and values
- 7.2.5 Short circuit – Check installation
- 7.2.6 Device memory failure – Restore default settings
- 7.2.7 Level measurement lost – Check application
- 7.2.8 Simulation active – Check operational mode
- 7.2.9 Device temperature over-run – Clear source of heat
- 7.2.10 Device temperature under-run – Insulate device
- 7.2.11 Primary supply voltage over-run – Check tolerance
- 7.2.12 Primary supply voltage under-run – Check tolerance
- 7.2.13 Maintenance required - Cleaning
- 7.3 Troubleshooting incorrect level readings
- 7.3.1 Reported level is too high or low
- 7.3.2 Level is stuck in measuring range
- 7.3.3 Level is stuck in full tank
- 7.3.4 Level value drops when close to antenna
- 7.3.5 Measured level fluctuates
- 7.3.6 Measured level is occasionally unstable
- 7.3.7 Lagging of measured level
- 7.3.8 Incorrect level at 100% (20 mA)
- 7.3.9 Incorrect level when product surface is above 50%
- 7.3.10 Dropping of level close to tank bottom
- 7.3.11 Level measurement is lost in an empty tank
- 7.3.12 Alarm mode close to tank bottom
- 7.4 Managing disturbance echoes
- 7.5 Service and troubleshooting tools
- 7.6 Service support
- A Specifications and reference data
- A.1 Performance specifications
- A.2 Functional specifications
- A.3 Physical specifications
- A.4 Dimensional drawings
- B Product certifications
- C Configuration parameters
components for hygienic seals meet the requirements stated in EMA/410/01 Rev. 3 and
ISO 22442-1:2015. Wetted components in hygienic seals are considered free of TSE.
A.3.3 Housing and enclosure
Materials
Polished stainless steel 316L (EN 1.4404)
Transmitter weight
1.1 lb (0.5 kg)
(4)
Ingress protection
• IP66/68
(5)
/69 (IEC 60529)
• IP6K9K (ISO 20563:2013)
• NEMA
®
4X
The stated ingress protection only applies when plugged in using a suitable M12
connector that has the appropriate ingress protection.
A.3.4 Surface finishes
Process wetted parts
• R
a
< 30 μ-in. (0.76 μ-m) for polymeric parts
• R
a
< 16 μ-in (0.4 μ-m) for metallic parts
Non-wetted parts
• R
a
< 30 μ-in. (0.76 μ-m) for stainless steel housing
A.3.5 Process connection
ISO 228/1-G1 thread with a wide choice of hygienic adapters
A.3.6 Material exposed to tank atmosphere
With adapter
• PTFE sealing: PTFE fluoropolymer
• Adapter: 316L (EN 1.4435)
• Hygienic O-ring: EPDM or FKM
(4) Adapter not included.
(5) IP68 at 9.8 ft. (3 m) for more than 30 minutes.
Specifications and reference data Reference Manual
September 2020 00809-0100-4480
78 Rosemount 1408H Level Transmitter