Specifications
Table Of Contents
- TWO YEAR LIMITED WARRANTY
- Safety Precautions
- 1. Introduction
- 2. Controls and Functions
- 3. Installation
- 3.1 Remote Control
- 3.2 Quick Setup
- 3.3 Installation Considerations
- 3.4 Installing the Optional CineWide Lens
- 3.5 Mounting the VX-2
- 3.6 Connections to the VX-2 and DHD Controller
- Connector Panel Access
- Connecting the DHD Controller to the VX-2
- Connecting Source Components to the DHD Controller
- RS-232 Controller Connection
- Connecting 12-Volt Trigger Outputs to External Theater Equipment
- Connecting to AC Power
- 4. Operation
- 4.1 Turning on the Power
- 4.2 Adjusting the Picture Orientation
- 4.3 Lens Adjustments
- 4.4 Using the On-Screen Menus
- 5. Maintenance and Troubleshooting
- 6. Serial Communications
- 7. Specifications
- Appendix A. VX-2 Color Gamut Adjustment
Operation
38 Runco VX-2cx/VX-2dcx Owner’s Operating Manual
PRE
L
IMINAR
Y
Figure 4-2. DHD Controller OSD Menu Structure for VX-2
Service
Test Video
Grey Bars 1
Grey Bars 2
Color Bars 1
Color Bars 2
Input Names Rename, Restore or Save
Remote Control
Primary
Secondary
Display Device
Installation
Picture Orientation
Lamp Hours (View/Reset)
Lens
Focus
Zoom
Shift (VX-2c ONLY)
Diagnostics
Red Only
Green Only
Blue Only
75 IRE Color Bars
100 IRE Color Bars
Horiz. Grey Ramp
Vert. Grey Ramp
Checkerboard
Alignment Grid
HD Format
HD/RGB 1
Auto, RGB or YUV
HD/RGB 2
ADC Bandwidth Auto, 75 MHz, 150 MHz or 300 MHz
YPbPr Input Resolution Auto, 480i/p, 576i/p, 720p or 1080i
Triggers 1 / 2 / 3 / Save
Miscellaneous
Language (currently, English only)
Menu Mode
Timeout
Side Bar Color
Film Mode (SD src. only)
Resolution
800x600 ... 1400x1050
480i ... 720p ... 1080i
System Reset
Restore Saved Settings
Note: Virtualwide 2.35 is
available only on VX-2
projectors equipped with the
CineWide option (secondary
anamorphic lens).
Input Source
Composite
S-Video 1
S-Video 2
Component SD
HD/RGB 1
HD/RGB 2
DVI 1
DVI 2
Aspect Ratio
Anamorphic
Standard 4:3
Letterbox
VirtualWide
Cinema
Virtualwide 2.35
Picture
Brightness
Contrast
Color
Tint
Sharpness
Input Position
Left/Right
Up/Down
Width
Height
Overscan
ISF Presets
Recall ISF Night
Recall ISF Day
Recall/Save Custom 1
Recall/Save Custom 2
Reset Custom 1 & 2 to Factory Default
Information
(read-only)
Serial Number
Hardware
Firmware
Date
Calibration
ISF Night - Display Color
Gain
Offset
Gamma
Lamp Power
Color Temp
ISF Night - Input Image
Brightness
Contrast
Color
Tint
Sharpness
ISF Night - Input Color
Gain
Offset
Chroma Delay
Phase
Noise Filter
ISF Day - Display Color
Gain
Offset
Gamma
Lamp Power
Color Temp
ISF Day - Input Image
Brightness
Contrast
Color
Tint
Sharpness
ISF Day - Input Color
Gain
Offset
Chroma Delay
Phase
Noise Filter
Save ISF Settings Back / Confirm
Output Shift
Left/Right
Up/Down
Width
Height
Save
Splash Configure
Owner Name
ISF Calibrated
ISF Other
OSD Position