Product Brochure

PREPARATION
REGARDLESS OF AGE OR CONDITION, FAILURE TO FOLLOW THIS PREPARATION METHOD WILL RESULT IN POOR ADHESION
AND POSSIBLE COATING FAILURE. NEW WOOD DECKS NEED TO WEATHER AT LEAST SIX MONTHS BEFORE APPLICATION.
PREPARATION WITH DECK STRIPPER
READ ALL INSTRUCTIONS BEFORE BEGINNING.
STEP 1 – REMOVE EXISTING STAIN/SEALER: Previously applied coatings need to be removed completely. Strip the surface using
a deck brush and deck stripper. Then, sand the surface using 50 or 60 grit sand paper.
STEP 2 – CLEAN: Clean the surface using a deck brush and RESTORE DECK & CONCRETE CLEANER. The surface must be clean
and free of dirt, grease, mildew and organic growth.
STEP 3 – TEST SURFACE FOR APPLICATION: Conduct a splash test by sprinkling water on at least four or more areas,
both high traffic and non-traffic areas. If the water absorbs rapidly into the wood, the surface is ready to coat.
If the water beads, puddles or is not absorbed, the surface is not ready to coat and requires more preparation.
Follow STEPS 1 and 2 until the water absorbs.
STEP 4 – LIGHT REPAIRS: Secure raised nail heads, decks screws or loose deck boards. Remove loose splinters and replace
severely damaged or rotting boards. Fill cracks with RESTORE CRACK FILLER or similar acrylic, non-silicone filler. Allow to dry.
PREPARATION FOR RESTORE 2X AND
RESTORE OUTDOOR FURNITURE
Proper preparation is important for top coat adhesion. Use the ground breaking clear
RESTORE DECK START WOOD PRIMER before applying RESTORE 2X ONE COAT SOLID STAIN
with Cool Touch Technology and RESTORE OUTDOOR FURNITURE instead of stripping and sanding.
Simply clean the surface and apply one coat of primer.
METHODS FOR PREPARATION
MÉTODOS DE PREPARACIÓN
PREPARACIÓN
INDEPENDIENTEMENTE DE LA EDAD O DE LA CONDICIÓN DE LA SUPERFICIE, NO SEGUIR TODOS ESTOS PROCEDIMIENTOS
DE PREPARACIÓN, CAUSARÁ QUE LA ADHERENCIA SEA INSUFICIENTE Y ES POSIBLE QUE EL REVESTIMIENTO FALLE.
LAS TERRAZAS DE MADERA NUEVAS NECESITAN ACLIMATARSE POR AL MENOS SEIS MESES ANTES DE REALIZAR LA APLICACIÓN.
PREPARACIÓN CON UN RASPADOR PARA TERRAZAS
LEE TODAS LAS INSTRUCCIONES ANTES DE COMENZAR
PASO 1 – QUITA LOS TINTES/SELLADORES EXISTENTES: Los revestimientos aplicados con anterioridad deben ser eliminados
completamente. Raspa la superficie con un cepillo para terrazas y un rellenador de grietas. Después, lija la superficie
con un papel de lija de grano 50 o 60.
PASO 2 – LIMPIEZA: Limpia la superficie usando un cepillo para terrazas y un raspador para terrazas. La superficie debe estar
limpia y libre de suciedad, grasa, moho y crecimiento orgánico.
PASO 3 – COMPRUEBA LA SUPERFICIE PARA LA APLICACIÓN: Realiza una prueba de salpicadura rociando agua en al menos
cuatro áreas o más, tanto en áreas de mucho tráfico como en áreas de ninguno. Si la madera absorbe el agua rápidamente,
la superficie está lista para el revestimiento. Si el agua no es absorbida, o se mantiene en gotas o charcos, la superficie no
está lista para el revestimiento y necesita más preparación. Repite los PASOS 1 y 2 hasta que la madera absorba el agua.
PASO 4 – REPARACIONES LIGERAS: Asegura las cabezas de clavos levantadas, los tornillos para terraza o las tablas de terraza sueltas.
Quita las astilladuras sueltas y reemplaza las tablas gravemente dañadas o podridas. Rellena las grietas con
RESTORE CRACK FILLER o un relleno similar de acrílico que no contenga silicona. Deja secar.
PREPARACIÓN PARA RESTORE 2X Y
RESTORE OUTDOOR FURNITURE
Una preparación adecuada es importante para una adhesión óptima del revestimiento. Usa el innovador
RESTORE DECK START WOOD PRIMER claro antes de aplicar el RESTORE 2X ONE COAT SOLID STAIN
con tecnología Cool Touch y RESTORE OUTDOOR FURNITURE en lugar de raspar y lijar. Simplemente limpia
la superficie y aplica una capa del imprimador.