Use and Care Manual

ManualsBrandsRust-Oleum Restore ManualsDeck Paint & Restoration5 gal. 4X Cedar Deck Coat

TECHNICAL DATA RST-07

RESTORE

4X DECK COAT

Form: GDH-443

Rev.: 030215

DESCRIPTION AND USES .

Restore

4X Deck Coat is a high build, water based acrylic

coating designed to resurface aged wood and concrete decks,

patios, and walkways. The high build finish provide slip

resistance and can bridge over or fill small cracks, checks, nail

holes, or other minor surface defects.

FOR DECKS: For wood and most composite decks. New

wood decks need to age at least six months before

application. Follow specific manufacturer’s

recommendation before applying to any composite

decking.

FOR CONCRETE: For use on broom swept or porous

concrete surfaces. Do not use on smooth or floated

concrete. Not recommended for driveways, garages or

other areas with vehicular traffic.

FOR EXTERIOR USE ONLY AND NOT RECOMMENDED

FOR DRIVEWAYS, GARAGES OR OTHER AREAS WITH

VEHICULAR TRAFFIC.

Restore 4X Deck Coat tint base must be tinted before use.

Restore 4X Deck Coat can be applied using a ⅜” or ½” nap

roller. Use of the Restore Honeycomb Roller is NOT

recommended.

. FEATURES .



Barefoot friendly



Conceals hairline cracks



Excellent coverage



For horizontal & vertical surfaces

.PRODUCTS .

SKU Description

41100 4X Deck Coat Tint Base – 1-Gallon

41500 4X Deck Coat Tint Base – 5-Gallon

282118 4X Deck Coat Timberline - 1-Gallon

282119 4X Deck Coat Cape Cod Gray – 1- Gallon

282120 4X Deck Coat Beach – 1-Gallon

282121 4X Deck Coat Navajo Red – 1-Gallon

282122 4X Deck Coat Timberline – 5-Gallon

282123 4X Deck Coat Cape Cod Gray – 5-Gallon

282125 4X Deck Coat Beach – 5-Gallon

282126 4X Deck Coat Navajo Red – 5-Gallon

COMPANION PRODUCTS ...

SKU Description

51752 Restore Deck & Concrete Cleaner

51750 Restore Crack Filler

287517 Restore Deck Start Wood Primer – 1-Gallon

287912 Restore Deck Stripper

PRODUCT APPLICATION .

REGARDLESS OF AGE OR SURFACE CONDITION,

FAILURE TO FOLLOW ONE OF THESE PREPARATION

METHODS WILL RESULT IN POOR ADHESION AND

POSSIBLE COATINGS FAILURE. NEW AND SEALED WOOD

DECKS NEED TO WEATHER AT LEAST 6 MONTHS

BEFORE APPLICATION.

PRODUCT APPLICATION .

SURFACE PREPARATION

NEW WOOD

New wood may be wet with chemicals or have mill glaze from

the manufacturing process. New wood should age for a

minimum of 6 months before applying Restore 4X Deck Coat.

The lumber must be dry completely before applying the product

to prevent peeling of the coating. The surface must also be

properly cleaned and prepared using Restore Deck & Concrete

Cleaner to remove all foreign material and mill glaze prior to

application. Follow the PREPARATION instructions to ensure

the Restore 4X Deck Coat adheres properly to the wood.

READ ALL INSTRUCTIONS BEFORE BEGINNING

PROJECT.

PREPARATION WITH RESTORE DECK START WOOD

PRIMER (HIGHLY RECOMMENDED)

Clean the surface using a deck brush and Restore Deck &

Concrete Cleaner. The surface must be clean and free of dirt,

grease, mildew and organic growth. Loose paint needs to be

scraped. For light repairs, secure raised nails heads, deck

screws or loose deck boards. Remove loose splinters and

replace severely damaged or rotting boards. Fill cracks with

Restore Crack Filler or similar acrylic, non-silicone filler. Allow to

dry. Apply Restore Deck Start Wood Primer using a ⅜” nap roller.

Saturate the roller cover and apply generously in a consistent

pattern. Work to a wet edge at all times.

WARNING! If you scrape, sand or remove old paint from any

surface, you may release lead paint dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS

ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN

CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID

EXPOSURE. Wear a NIOSH approved respirator to control lead

exposure. Clean up carefully with a HEPA vacuum and a wet

mop. Before you start, find out how to protect yourself and your

family by contacting the National Lead Information Hotline at

1-800-424-LEAD or log on to www.epa.gov/lead.

PREPARATION WITH RESTORE DECK STRIPPER

Previously applied coatings and existing stain/sealers need to be

removed completely. Strip the surface using a deck brush and

Restore Deck Stripper. Then sand the surface using 50 or 60 grit

sandpaper. Follow by cleaning the surface using a deck brush

and Restore Deck & Concrete Cleaner. The surface must be

clean and free of dirt, grease, mildew and organic growth.

Conduct a splash test by sprinkling water on at least four or more

areas, both in high traffic and non-traffic areas. If the water

absorbs rapidly into the wood, the surface is ready to coat. If the

water beads, puddles or is not absorbed, the surface is not ready

to coat and requires more surface preparation. Continue the

process until the water absorbs into the wood in all test areas.

Secure all raised nail heads, deck screws, or loose deck boards.

Remove loose splinters and replace severely damaged or rotting

boards. Fill cracks with Restore Crack Filler or similar acrylic,

non-silicone filler. Allow to dry.

Summary of content (3 pages)

PAGE 1
TECHNICAL DATA RST-07 RESTORE® 4X DECK COAT DESCRIPTION AND USES . PRODUCT APPLICATION ® Restore 4X Deck Coat is a high build, water based acrylic coating designed to resurface aged wood and concrete decks, patios, and walkways. The high build finish provide slip resistance and can bridge over or fill small cracks, checks, nail holes, or other minor surface defects. FOR DECKS: For wood and most composite decks. New wood decks need to age at least six months before application.
PAGE 2
TECHNICAL DATA RESTORE® 4X DECK COAT PRODUCT APPLICATION (cont) . PRODUCT APPLICATION (cont) . PRECAUTIONS & TEMPERATURE SAFEGUARDS DRY TIMES DO NOT APPLY IF RAIN IS EXPECTED WITHIN 48 HOURS OF APPLICATION. Apply when sir and surface temperatures are between 50-90°F (10-32°C) for a full 72 hours (day and night) after application. Dries to the touch in 2 hours and can be recoated in 4-6 hours. Longer dry time is required in cooler temperatures and at higher humidity.
PAGE 3
TECHNICAL DATA RESTORE® 4X DECK COAT PHYSICAL PROPERTIES . 4X DECK COAT Resin Type Water-based Acrylic Pigment Type A blend of inorganic and organic pigments Solvents Glycol Ethers, Water Per Gallon 11.6-11.9 lbs Per Liter 1.39-1.43 kg Weight By Weight 66-69% By Volume 53.4-54.4% Solids Volatile Organic Compounds <50 g/l (0.42 lbs./gal.) Recommended Dry Film Thickness (DFT) Per Coat Practical Coverage at Recommended DFT 4 mils Approximately 80 sq.ft./gal.