OPERATOR’S MANUAL ELECTRIC LOG SPLITTER RY49701 Your Log Splitter has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product.
TABLE OF CONTENTS n Introduction ...................................................................................................................................................................... 2 �n General Safety Rules .....................................................................................................................................................3-4 �n Specific Safety Rules.............................................................................................................
GENERAL SAFETY RULES n DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected from power source. n AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool. n USE RECOMMENDED ACCESSORIES. Consult the operator’s manual for recommended accessories. The use of improper accessories may result in injury. n NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped. n CHECK DAMAGED PARTS.
GENERAL SAFETY RULES n WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. n ALWAYS STAY ALERT! Do not allow familiarity (gained from frequent use of your tool) to cause a careless mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ELECTRICAL EXTENSION CORDS SPEED AND WIRING Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat.
FEATURES PRODUCT SPECIFICATIONS Hydraulic Cylinder Pressure................................. 2320 psi Log Capacity Diameter, maximum............................ 10 in. Oil Capacity ......................................... 118 oz. (3.7 quarts) Log Capacity Diameter, minimum............................... 4 in. Input ................................120 V, 60 Hz, AC only, 15 Amps Log Capacity Length .............................................. 20.5 in. Net Weight`......................................
ASSEMBLY UNPACKING AXLE This product has been shipped completely assembled. n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping. n Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. n If any parts are damaged or missing, please call 1-800-860-4050 for assistance.
OPERATION WARNING: BLEED SCREW Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool.
OPERATION STARTING THE LOG SPLITTER See Figures 6 - 7. n Operator should be positioned at the rear of the log splitter as shown in figure 7. n Place the left hand on the hydraulic control lever and the right hand on the on/off switch. n Push down and hold the on/off switch. n While continuing to hold down the on/off switch, push down and hold the hydraulic control lever. NOTE: Both hands are required to start this product. The combination of both steps starts the ram which pushes the log into the wedge.
OPERATION FREEING A JAMMED LOG See Figures 10 - 11. n Release both controls. n After the ram is back at the starting position, insert a wood wedge under the jammed log. n Start the log splitter to push the wood wedge completely under the jammed log. n If the log is still jammed, repeat the above steps as needed using a thicker angled wood wedge until the log is completely freed. NOTE: Never try to knock the jammed log off the splitter.
MAINTENANCE NOTE: The oil level should be between the two grooves around the bottom of the dipstick as shown in figure 5. n Replace oil drain bolt. Tighten securely. n Dispose old oil at an oil recycling center. WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. SHARPENING THE WEDGE After using the log splitter for some time, it may be necessary to sharpen the wedge.
TROUBLESHOOTING PROBLEM Motor fails to start Won’t split logs POSSIBLE CAUSE SOLUTION 1. Overload Protection Device is disengaged to protect the log splitter from being damaged. 1. Push reset button. 1. Log is improperly positioned. 1. Refer to Operation section for log loading. 2. Reduce the log size before splitting. 2. The size or hardness of the log exceeds the machine’s capacity. 3. Wedge cutting edge is blunt. 4. Oil leaks. 5.
NOTES 15
OPERATOR’S MANUAL ELECTRIC LOG SPLITTER RY49701 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO.