Use and Care Manual

ManualsBrandsRyobi ManualsMiscellaneous PartsReel Easy Trimmer Head with Speed Winder

REEL-EASY

™

TRIMMER HEAD

WITH SPEED WINDER

™

AC04156

WARNING:

To reduce the risk of injury, user must read and understand the

operator’s manual for their string trimmer before using this accessory.

Always wear eye protection with side shields marked to comply

with Z87.1 along with hearing protection. Ensure compatibility and

proper fit before using this accessory. Stop the string trimmer and

remove battery pack or disconnect spark plug wire before changing

or adjusting accessories.

WARNING:

Do not use this accessory if a part is damaged or missing. If you are

not comfortable performing any of the functions described in these

instructions, take your unit to an authorized service center. Use of a

trimmer head that has been improperly assembled could cause the

trimmer head to come apart and/or detach from your trimmer and

result in serious personal injury and/or property damage.

PACKING LIST

See Figures 1 - 2.

Trimmer Head Assembly, Spacer, Silver Bolt, Black Bolt, Silver Nut, Black

Nut, Black Line Guide, White Line Guide, 0.095 in. Line (16 ft.), Locking

Pin and Operator’s Manual

INSTALLING TRIMMER HEAD

See Figures 1 - 6.

The REEL-EASY

™

Trimmer Head installs differently on different string

trimmer attachments. Assembly instructions will vary based on the style

and type of attachment you have. See figures 3 and 4 to determine if you

have a curved shaft or straight shaft attachment and if your attachment

comes with or without an arbor. Refer to the Installation Chart to

determine the appropriate items for your attachment. Be sure to follow

the instructions for your attachment style and type.

NOTE: If you cannot identify the style and type of attachment you have,

contact customer service for assistance.

Stop the unit and remove battery pack or disconnect spark plug wire.

Open the REEL-EASY

™

Trimmer Head assembly by depressing the

tabs on each side. The contents of the trimmer head are spring loaded,

so keep your other hand over the lower housing while depressing

the tabs.

Seperate the upper housing, spring, spool, knob, from lower housing

and set aside.

Locate the bolt, nut, line guide, and/or spacer required to install the

trimmer head to your attachment. Refer to the Installation Chart for

details.

INSTALLATION CHART

If the trimmer head does not fit with any of the adaptors or

hardware supplied, contact Customer Service at 1-800-860-4050

for assistance.

Style Type Items Needed for Installation

Curved

Shaft

With

Arbor

Spacer, White Line Guide, Black Bolt,

and Trimmer Head Assembly

Curved

Shaft

Without

Arbor

Silver Nut, Black Line Guide,

and Trimmer Head Assembly

Straight

Shaft

With

Arbor

Spacer, White Line Guide, Silver Bolt,

and Trimmer Head Assembly

Straight

Shaft

Without

Arbor

Black Nut, Black Line Guide,

and Trimmer Head Assembly

Fig. 3

Fig. 4

Fig. 1

Fig. 2

STRAIGHT

SHAFT

UPPER

HOUSING

LOWER

HOUSING

SILVER

BOLT

SILVER

NUT

LOCKING

BLACK

NUT

BLACK

BOLT

BLACK

LINE GUIDE

WHITE

LINE GUIDE

CURVED

SHAFT

CURVED SHAFTS

STRAIGHT SHAFTS

ARBOR

SPRING

SPACER

TAB

SPOOL

KNOB

995000139

11-1-16 (REV:01)

Summary of content (6 pages)

PAGE 1
REEL-EASY™ TRIMMER HEAD WITH SPEED WINDER™ AC04156 WARNING: TAB To reduce the risk of injury, user must read and understand the operator’s manual for their string trimmer before using this accessory. Always wear eye protection with side shields marked to comply with Z87.1 along with hearing protection. Ensure compatibility and proper fit before using this accessory. Stop the string trimmer and remove battery pack or disconnect spark plug wire before changing or adjusting accessories.
PAGE 2
For units with arbors:  Install the spacer onto the upper housing.  Slide the spacer and upper housing onto the arbor.  Place the spring into the upper housing and push down to seat.  Install the white line guide into the spool. NOTE: When installing, align the keys located on the underside of the guide with the corresponding holes in the spool.  Insert the spool into the upper housing and onto the arbor.
PAGE 3
TÊTE DE COUPE DE REEL-EASY™ AVEC SPEED WINDER™ ERGOT ERGOT AC04156 BOÎTIER SUPÉRIEUR AVERTISSEMENT : Pour réduire les risques de blessure, l’utilisateur doit lire et comprendre le manuel d’utilisation de son taille-bordures avant d’employer cet accessoire. Toujours porter une protection oculaire certifiée conforme à la norme ANSI Z87.1 ainsi qu’un protection auditive. S’assurer que l’accessoire est compatible et qu’il est bien installé avant de l’utiliser.
PAGE 4
Pour les unités équipées d’un axe :  Installez l’entretoise sur la section du boîtier supérieur.  Glissez l’entretoise et la section du boîtier supérieur sur l’axe.  Placez le ressort sur la section du boîtier supérieur et poussez dessus.  Installez le guide de ligne blanc dans la bobine. NOTE : Lors de l’installation, alignez les clavettes situées sur le côté inférieur du guide avec les trous correspondants dans la bobine.  Insérez la bobine dans la section du boîtier supérieur et sur l’axe.
PAGE 5
CABEZAL DE LA RECORTADORA REEL-EASY™ CON SPEED WINDER™ LENGÜETAS LENGÜETAS AC04156 ARMAZÓN SUPERIOR ADVERTENCIA: Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador de la recortadora de hilo antes de usar este accesorio. Siempre póngase protección ocular con la marca de cumplimiento de la norma ANSI Z87.1 junto con protección auditiva. Asegúrese de que sea compatible con el producto antes de utilizar este accesorio.
PAGE 6
Para las unidades con árboles:  Instale el separador en el armazón superior.  Deslice el separador y el armazón superior en el árbol.  Coloque el resorte en el armazón superior y empuje hacia abajo.  Instale la guía de línea blanca en el carrete. NOTA: Al realizar la instalación, alinee las muescas ubicadas en la parte inferior de la guía con los orificios correspondientes en el carrete.  Inserte el carrete en el armazón superior y luego en el árbol.