Specifications

Chapter 9: Specifications
Firmware – S2011 and S3012
Revision: 1 (9/98) 74 © Saftronics, Inc.
Table 25 400 V Class Specifications (FP5/GP5)
Models
FP5/GP5
4018 4022 4030 4037 4045 4055 4075 4110 4160 4185 4220 4300
Maximum Applicable Motor
Output * (kW)
18.5 22 30 37 45 55 75 110 160 185 220 300
Inverter Capacity (kVA) 31 40 50 61 73 98 130 170 230 260 340 460
Rated Output Current (A) 41 52 65 80 96 128 165 224 302 340 450 605
Maximum Output Voltage 3-Phase, 380/400/415/440/460 V (Proportional to input voltage)
Output
Characteristics
Rated Output Frequency Up to 400 Hz available by programming
Rated Input Voltage and
Frequency
3-Phase 380/400/415/440/460 V 50/60 Hz
Allowable Voltage
Fluctuation
+ 10%, − 15%
Power
Supply
Allowable Frequency
Fluctuation
± 5%
Control Method Sine wave PWM
Frequency Control Range 0.1 to 400 Hz
Digital Command: ± 00.1% (− 10°C + 40°C)
Frequency Accuracy
Analog command: ± 0.1% (25°C ± 10°C)
Digital Operator reference: 0.1 Hz
Frequency Resolution
Analog reference: 0.1 Hz
Output Frequency
Resolution
0.1 Hz
Overload Capacity 120% of rated output current for 1 minute.
Frequency Setting Signal 0 to + 10 V (20kΩ), 4 to 20 mA (250Ω)
Accel/Decel Time 0.0 to 3600 seconds (Accel/decel time setting independently)
Braking Torque
Approximately 20%
(Braking Resistor cannot be mounted)
Approximately 20%
(Approximately 100% with Braking Unit and
Braking Resistor)
Control Characteristics
Number of V/f Patterns 15 preset V/f patterns, 1 custom V/f with voltage limit, 1 custom without voltage limit
Motor Overload
Protection
Protected by electronic Thermal Overload Relay
Instantaneous
Overcurrent
Motor coasts to a stop at approximately 180% of Inverter rated current.
Overload Motor coasts to a stop after 1 minute at 120% of rated output current.
Overvoltage Motor coasts to a stop if converter output voltage exceeds 820 V.
Undervoltage Motor coasts to a stop if converter output voltage drops to 380 V or below.
Momentary Power Loss
Immediately stop by 15 ms and above momentary power loss. (Factory setting)
Continuous operation during power loss less than 2 seconds is equipped as standard.
Heatsink Overheat Protected by thermistor.
Stall Prevention Stall Prevention during accel/decel and constant speed operation.
Ground Fault Protected by electronic circuit.
Protective Functions
Power Charge Indication CHARGE LED stays ON until bus voltage drops below 50 V.
Ambient Temperature
− 10°C to + 40°C (Enclosed wall-mounted type)
− 10°C to + 45°C (Open chassis type)
Humidity 90% RH or less
Storage Temperature −20°C to + 60°C
Locatioan Indoor (protected from corrosive gases and dust)
Elevation 1000 meters or less
Environment
Vibration 9.81m/s
2
(1G) at 10 to less than 20 Hz, up to 1.96m/s
2
(0.2G) at 20 to 50 Hz.
∗Based on a Saftronics standard 4-pole motor for maximum applicable motor output.
efesotomasyon.com - Control Techniques,emerson,saftronics -ac drive-servo motor