Owner's manual

ManualsBrandsSaltDogg ManualsCarSHPE1000 Series Electric Drive Poly Hopper Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

—continued inside

SHPE1000 Series

SaltDogg

Electric Drive

Poly Hopper Spreader

1.0 cubic yards

Serial numbers 8500 and higher

Table of Contents

General Information ...................................................................1

Safety Precautions ......................................................................1

Warranty Information .................................................................2

Installation Instructions ........................................................ 2-4

Spreader Operation .....................................................................5

Spreader Maintenance ...............................................................5

Repair Parts & Drawings ......................................................6-10

General Information

Spreader models:

• SHPE1000- spreader with standard length chute

• SHPE1000X- spreader with extended length chute

Overall Length: 72 inches

Overall Width: 48 inches

Overall Height: (installed): 34 inches

Empty Weight: 343 lbs. (standard chute), 347 lbs. (extended

chute)

Capacity Struck: 1.0 cu. yd.

Vehicle Requirements

• 3/4 or 1 ton pick-up truck above 8500# GVWR.

• 135 AMP or higher alternator is recommended.

SHPE1000 SALT DOGG SPREADER WARRANTY

INFORMATION

This warranty replaces all previous warranties and

no employee of this company is authorized to extend

additional warranties, or agreements, or implications

not explicitly covered herein.

Buyers Products Company warrants all parts of the

product to be free from defects in material and work-

manship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including modifica-

tions, misuse, accident, or lack of maintenance will

not be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replac-

ing any part(s), which are returned, prepaid, 30

days after such defect is discovered, and returned

part(s) are found to be defective by Buyers Products

Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from

whom purchased.

Buyers Products Company shall not be liable for

damage arising out of failure of any unit to operate

properly, or failure, or delay in work, or for any con-

sequential damages. No charges for transportation

or labor performed on any part will be allowed under

this warranty.

CAUTION

Do not overload vehicle beyond the vehicle’s GVWR or GAWR.

Check vehicle's load rating certification sticker for maximum

vehicle capacity.

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 1,250

Coarse Salt-Dry 950

Sand/Salt up to 50/50 Mix-Dry 2,700

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Installation Instructions SHPE1000 Series SaltDogg® Electric Drive Poly Hopper Spreader 1.0 cubic yards Serial numbers 8500 and higher Table of Contents General Information....................................................................1 Safety Precautions.......................................................................1 Warranty Information..............................
PAGE 2
TM F. Attach the Chute Assembly to the spreader. First, hook the Chute to the spreader by openings in the Chute’s handle. Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1. Read this entire Owners Manual before operating this spreader. 2. Read all safety decals on the spreader before operating. 3.
PAGE 3
TM Fig. 4 2" x 6" FIT TO BOX WARNING Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. 6 2. Install Control Box & Vehicle Wiring Harness (Fig. 7). NOTE: THIS IS A WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK'S FRAME OR BODY ALLOWED! ALWAYS DISCONNECT BATTERY BEFORE ATTEMPTING TO INSTALL ELECTRICAL COMPONENTS ON YOUR VEHICLE. 2" x 4" 12 WARNING FIT TO BOX Use extreme caution when working around an operating vehicle engine.
PAGE 4
TM Fig. 7 CONNECT TO BATTERY POWER CABLE #3006842 MAIN WIRE HARNESS #3006724 CONNECT TO CHUTE CONNECT FUSE CONNECTOR CONNECT TO FUSE TERMINAL OR IGNITION SWITCH WIRE 36" LONG #0203700 (IF EQUIPPED) CONNECT BROWN WIRE CONNECT TO UTILITY LIGHT CONNECT OPTIONAL #3018009 CONTROLLER #3014199 CONNECT TO KNOWN GROUND CONNECT TO MOTOR COMPARTMENT HARNESS 2. When filling hopper use the supplied screen to prevent large chunks of material and debris in the material to get into hopper and cause damage.
PAGE 5
TM Controller Warnings 5. Use dielectric grease on all electrical connectors before an electrical connection is made or after connector is disconnected 6. Empty the spreader of all ice control materials when not in use. Wash out the spreader to prevent material builds up. 7. It is recommended to cover spreader with the tarp during storage periods. Check controller instruction sheet for latest controller updates and troubleshooting codes. Controller instruction sheet is inside controller shipping box.
PAGE 6
TM Repair Parts-Chute Assembly Bill of Materials 16 17 item 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 15 3 part no. 3007329 3007526 3006833 3007824 — 3007564 — 3004611 3007299 3007004 3007413 3006753 — — — — — — 3002631 3007844 5 2 qty. 1 1 1 1 3 1 3 1 1 1 1 1 16 10 10 6 1 1 1 1 description Chute Poly Std. Length Chute Poly Ext.
PAGE 7
TM Repair Parts-Hopper Assembly Bill of Materials item part no. qty. description 1 3022973 1 HOPPER POLY 1 CU YA 2 3 4 5 6 7 8 9 3024289 3022230 3022976 3024288 — — 3007416 — 1 2 1 2 6 4 1 4 10 11 12 — — — 16 10 12 TROUGH ASSEMBLY, SHPE CROSS MEMBER BRACKET VIBRATOR, WELDMENT RETAINER VIBRATOR WASHER, FLAT 3/8 USS SST NUT, NYLOCK 3/8-16 X 7/16 SST VIBRATOR 200 LBS 12 VDC WASHER, EXTERNAL TOOTH LOCK 3/8 SS SCREW, HHC-3/8-16 X 3/4 SST WASHER, FLAT 3/8 X 1.5 X.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Repair Parts- Spreader Bill of Materials item part no. qty. 1 2 3 4 5 6 7 8 3022974 3007412 3022978 66050 3024292 3014199 3006724 3006842 1 1 1 4 1 1 1 1 description HOPPER ASS'Y 1 CU YA CHUTE POLY STD. SHPE1500 SCREEN SHPE1000 SNAPPER PIN, 1/4 X 2, YLW ZINC HARDWARE KIT SHPE1000 CONTROLLER, SHPE, SALT DOGG WIRE HARNESS, MAIN POWER CABLE, CONTROL BOX 8 item part no. qty.