Installation Instructons (21000+ Serial Number)

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment2.0 cu. yds. Electric Black Poly Hopper Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

—continued inside

SHPE2000, SHPE2000RED, SHPE2000YEL

Series SaltDogg

Electric Drive Poly Hopper

Spreader

2.0 cubic yards

U.S. PATENT 9,562,333

Serial Number 21000 and Above.

Table of Contents

General Information .....................................................................1

Safety Precautions .......................................................................1

Warranty Information ...................................................................2

Installation Instructions ............................................................ 2-4

Spreader Operation .....................................................................5

Spreader Maintenance .................................................................5

Repair Parts & Drawings .........................................................6 -10

General Information

Spreader models:

• SHPE2000- spreader with standard length chute

• SHPE2000X- spreader with extended length chute

Overall Length: 96 inches

Overall Width: 48 inches

Overall Height: (installed): 41.5 inches

Empty Weight: 5

60 lbs. (standard chute), 564 lbs. (extended chute)

Capacity Struck: 2.0 cu. yd.

Average Installation Time: 3 hrs.

Vehicle Requirements

• 3/4 or 1 ton pick-up truck above 8500# GVWR.

• 135 AMP or higher alternator is recommended.

Materials Recommended to Spread

SHPE2000 SALTDOGG SPREADER WARRANTY INFORMATION

This warranty replaces all previous warranties and no employee of this

company is authorized to extend additional warranties, or agreements, or

implications not explicitly covered herein.

Buyers Products Company warrants all parts of the product to be free

from defects in material and workmanship for a period of two (2) years.

Parts must be properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including modifications, misuse, acci-

dent, or lack of maintenance will not be considered under this warranty.

The sole responsibility of Buyers Products Company under this warranty

is limited to repairing or replacing any part(s), which are returned, pre-

paid, 30 days after such defect is discovered, and returned part(s) are

found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must be obtained before

returning any part. The following information must accompany defective

parts returned to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from whom purchased.

Buyers Products Company shall not be liable for damage arising out of

failure of any unit to operate properly, or failure, or delay in work, or for

any consequential damages. No charges for transportation or labor per-

formed on any part will be allowed under this warranty.

CAUTION

Do not overload vehicle beyond the vehicle’s GVWR or GAWR.

Check vehicle's load rating certification sticker for maximum

vehicle capacity.

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 2,250

Coarse Salt-Dry 1,431

Sand/Salt up to 50/50 Mix-Dry 2,700

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions SHPE2000, SHPE2000RED, SHPE2000YEL Series SaltDogg® Electric Drive Poly Hopper Spreader 2.0 cubic yards U.S. PATENT 9,562,333 Serial Number 21000 and Above. Table of Contents General Information......................................................................1 Safety Precautions........................................................................
PAGE 2
Safety Precautions F. Attach the Chute Assembly to the spreader. First, hook the Chute to the spreader by openings in the Chute’s handle. WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. Fig. 2 1. Read this entire Owners Manual before operating this spreader. 2. Read all safety decals on the spreader before operating. 3.
PAGE 3
Fig. 4 TO FIT BED WIDTH WARNING Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. 2" X6" TO FIT BETWEEN SPREADER AND FRONT OF THE BED 2. Install Control Box & Vehicle Wiring Harness (Fig. 7). NOTE: THIS IS A WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK'S FRAME OR BODY ALLOWED! ALWAYS DISCONNECT BATTERY BEFORE ATTEMPTING TO INSTALL ELECTRICAL COMPONENTS ON YOUR VEHICLE. 12.0 16.
PAGE 4
3001379 CB120PB Fig. 7 BATTERY POSITIVE BATTERY NEGATIVE 3035933 3006724 3014199 2. When filling hopper use the supplied screen to prevent large chunks of material and debris in the material to get into hopper and cause damage. 3. Material must never be left in hopper for an extended period of time. Material will absorb moisture, bind, harden and could prevent spreader from proper operation or may damage the spreader. Empty and clean after each use. Thoroughly clean battery terminals.
PAGE 5
Material Flow Adjustments Spreader Maintenance Always use screen during spreader operation! Various materials have different moisture absorption rate, some materials may not perform as desired. Therefore, the substitution of the alternate material may be necessary for optimum performance. 1. Wash spreader after every use. Make sure no material is left under auger and/or inside trough. 2. Inspect and retighten fasteners after every 5-7 hours of operation. 3.
PAGE 6
Repair Parts - Standard Chute Assembly Repair Parts - Extended Chute Assembly 1 4 19 7 7 14 6 13 17 10 5 11 1 11 12 19 18 2 18 13 14 3 12 8 8 2 9 16 10 3 15 9 5 20 17 4 15 6 Bills of Material 16 Bills of Material ITEM PART NO. QTY.
PAGE 7
Repair Parts-Hopper Assembly 10 9 7 8 6 24 23 26 22 21 25 1 27 2 14 19 20 15 11 16 17 Bills of Material ITEM PART NO. QTY. DESCRIPTION 18 5 4 ITEM PART NO. 3007821 3020713 3022955_ H3309X2 800 4375 1 1 1 1 1 4 3036868 1 HOPPER POLY 2 CU YD, YELLOW 2 3024289 1 TROUGH ASSEMBLY, SHPE 3 3007115 10 WASHER, FLAT 3/8 X 1.5 X.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Repair Parts-Trough Assembly 6 Repair Parts- Spreader 8 9 7 11 10 13 5 14 15 16 10 9 1 12 8 7 2 6 3 4 Bills of Material ITEM PART NO. QTY.