Manual

ManualsBrandsSaltDogg ManualsCarSHPE2250 Series Electric Drive Poly Hopper Spreader

Safety Precautions

1. Read the entire Installation Instructions before operating

this spreader.

2. Read all safety decals on the spreader before operating.

3. Check to make sure all safety guards are securely

mounted into place before operating this spreader.

4. Verify that all personnel are clear of the spreader spray

area before starting or operating this spreader.

5. Do not over-load your vehicle beyond payload limits. If

there are any questions, contact the vehicle manufacturer.

6. Do not adjust, clean, lubricate or unclog material jambs

without first turning off the spreader.

7. Do not climb on or in the spreader during operation. Do not

ride on the spreader while the vehicle is in motion.

8. Make sure the spreader is securely fastened to the vehicle

in accordance with this manual.

9. Do not operate a spreader that is in need of maintenance

or repairs.

10. Batteries normally produce explosive gases which can

cause personal injury. Always disconnect the battery before

removing or replacing electrical components.

11. Do not leave unused material in hopper. Material can

freeze or solidify, causing spreader to not work properly, and/

or damage the unit. Empty and clean after each use.

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (800) 841-8003

www.saltdogg.com

Installation Instructions

SHPE2250, SHPE2250RED,

SHPE2250YEL SaltDogg

Electric

Drive Poly Hopper Spreader

2.2 cubic yards

—continued inside

Table of Contents

General Information ................................................................. 1

Safety Precautions .................................................................... 1

Installation Instructions ....................................................... 2-4

Spreader Operation ................................................................... 5

Spreader Maintenance ............................................................. 5

Repair Parts & Drawings ...................................................... 6-8

Warranty Information ............................................................... 8

General Information

Overall Length: 104.5 inches

Overall Width: 48 inches

Overall Height: 44 inches

Empty Weight: 707 lbs

Capacity Struck: 2.2 cu. yd.

Vehicle Requirements

Trucks with minimum GVWR 13,000 lbs.

150 AMP or higher alternator is recommended.

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 2,250

Coarse Salt-Dry 1,431

Sand Coarse-Dry 2,565

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

WARNING

Improper installation and operation could cause personal

injury, and/or property damage. Observe the following

Safety Precautions before, during and after operating this

spreader. By following these precautions and common

sense, possible injury to persons and potential damage to

this machine may be avoided.

CAUTION

Do not overload vehicle beyond the vehicle’s GVWR or

GAWR. Check vehicle’s load rating certification sticker

for maximum vehicle capacity.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Installation Instructions SHPE2250, SHPE2250RED, SHPE2250YEL SaltDogg® Electric Drive Poly Hopper Spreader 2.2 cubic yards CAUTION Do not overload vehicle beyond the vehicle’s GVWR or GAWR. Check vehicle’s load rating certification sticker for maximum vehicle capacity. WARNING Improper installation and operation could cause personal injury, and/or property damage.
PAGE 2
Installation Instructions Lower opening is for pick-up trucks. Rest chute on top of chute guide as shown in Fig. 2 G. Using holes in chute guide as guides, drill 4 clearance holes for 3/8 dia. bolts. Bolt chute guide to chute as shown in Fig. 3 H. Detent spring latches located on chute slides. Slide chute guide into chute slides and secure chute in position by releasing spring latches Fig. 4 I. Slide spreader forward to have at least 1”-2" clearance between chute and rear most vertical obstruction. J.
PAGE 3
Fig. 2 Fig. 3 DRILL HOLES THRU CHUTE. ASSEMBLE CHUTE GUIDE TO CHUTE AS SHOWN REST CHUTE ON TOP OF CHUTE GUIDE Fig. 4 Fig. 5 SLIDE CHUTE GUIDE INTO CHUTE BRACKET. SECURE CHUTE USING LATCH. SPACER 12.0" 27.0" 9.
PAGE 4
2. Control Box and Vehicle Wiring Harness Installation E. Connect the 2-pin connector on the power cable to the control box mating connector. F. Connect wire harness single connectors to control box connectors. G. Connect fuse connector to the fuse terminal or ignition switch (5 AMP max). H. Lay out a path for the power cable to the battery, use quick ties to secure power cable. DO NOT CONNECT TO BATTERY AT THIS TIME! I. Lay out path for wire harness to the rear of the vehicle.
PAGE 5
Spreader Maintenance Tarp Installation ATTACH HOOKS TO STRAP METAL RINGS Spreader Operation 1. Wash spreader after every use. Make sure no material is left under auger and/or inside trough. 2. Inspect and retighten fasteners after every 5-7 hours of operation. 3. Lubricate bearings every 7-10 hours of operation using general automotive grease. (fig. 6) 4. Inspect terminals/connectors every time you disconnect spreader from wire harness. Apply thin layer of dielectric grease on terminals.
PAGE 6
Repair Parts- Trough Assembly 13 4 5 2 1 3 15 Bill of Materials 14 ITEM PART NO. QTY. 1 2 3 4 5 6 7 3013821 3014858 3019902 – – 3019903 3020117 1 1 1 1 1 1 1 6 8 DESCRIPTION GEAR MOTOR CONVEYOR 1 2 VDC SLEEVE, AUGER ADAPTER AUGER SHPE 5.25 VARIABLE RH SCREW, HHC-1 72-13 X 3 SST NUT, NYLOCK 1/2-13SS TROUGH ASSEMBLY SHPE2500 BRACKET BEARING, WELDMENT ITEM PART NO. QTY.
PAGE 7
Repair Parts- Hopper Assembly 10 8 9 14 13 12 11 1 4 7 6 5 3 2 Bill of Materials ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. QTY. 3019900 3025170 3025172 – 3020046 – 3007416 – – 3020053 3020096 – 3020121 – 3020145 — 1 1 1 10 1 14 1 4 4 2 4 12 1 4 1 4 DESCRIPTION HOPPER SHPE2250 HOPPER SHPE2250, RED HOPPER SHPE2250, YELLOW WASHER, FLAT 3/8 X 1 .5 X.048 SST BRACKET, VIBRATOR WELDMENT WASHER FLAT .5 ID 1 .
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com 17 Repair Parts- Spreader Assembly 13 14 12 15 4 16 1 2 9 3 8 6 7 10 5 SHPE2250 SALTDOGG® SPREADER WARRANTY INFORMATION Bill of Materials ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 11 PART NO. QTY.