Replacement Part List

ManualsBrandsSaltDogg ManualsKitchenCommercial Electric Poly Tailgate Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

TGS02 SaltDogg

Tailgate Spreader

—continued inside

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By following

these precautions and common sense, possible injury

to persons and potential damage to this machine may be

avoided.

SPREADER WARRANTY

This warranty replaces all previous warranties and

no employee of this company is authorized to extend

additional warranties, or agreements, or implications

not explicitly covered herein.

Buyers Products Company warrants all parts of

the product to be free from defects in material and

workmanship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including

modifications, misuse, accident, or lack of maintenance

will not be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing

any part(s), which are returned, prepaid, 30 days after

such defect is discovered, and returned part(s) are

found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from

whom purchased.

Buyers Products Company shall not be liable for

damage arising out of failure of any unit to operate

properly, or failure, or delay in work, or for any

consequential damages. No charges for transportation

or labor performed on any part will be allowed under

this warranty.

Safety Precautions

1. Read this entire Installation Instruction before

operating this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating

this spreader.

4. Do not adjust, clean, lubricate or unclog material

jams without first turning off the spreader.

5. Make sure the spreader is securely fastened to

the vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of

maintenance or repairs.

7. Always disconnect the battery before removing

or replacing electrical components.

Materials Recommended to Spread

• Pelletized Ice Melt

• Bagged Rock Salt, Dry Free flowing

Average Installation Time

• 1-2 hours

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions TGS02 SaltDogg® Tailgate Spreader Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1. Read this entire Installation Instruction before operating this spreader. 2.
PAGE 2
Spreader Assembly Check contents of box against parts list to make sure all components are included. When ordering replacement or spare parts refer to parts list for part numbers. 1. Insert frame #3024170 into hitch receiver. (Fig.1) Fig. 1 2. Insert round plugs into frame tubes as shown. Lower hopper assembly onto frame tubes. Align holes in hopper with holes in frame. Secure hopper to frame using 1/4 screws, washers and nuts as shown. (Fig.2) Fig. 2 SCREW, CAP HEX HD 1/4-20X2.
PAGE 3
5. Assembly brackets and rubber handles to lid using #10 button head screws. (Fig.5) 3. Align holes in frame and hitch receiver. Secure frame in hitch receiver using 5/8” hitch pin and cotter pin. (Fig.3) Fig. 5 BRACKET, RUBBER HANDLE Fig. 3 SCREW, BHC #10-24 X .75 SST INSIDE LID 5/8" HITCH PIN PIN, HAIR COTTER, CLEAR ZINC 4. Assembly catchers to hopper using #10 button head screws. (Fig.4) Fig. 4 SCREW, BHC #10-24 X .
PAGE 4
CONNECT TO BATTERY RED-POSITIVE BLACK-NEGATIVE WIRE HARNESS POWER #3008615 CONNECT TO GEAR MOTOR #3024587 CONNECT TO OPTIONAL VIBRATOR KIT #3028195 INSULATE IF NOT IN USE WIRE HARNESS W/ VIBRATOR CONNECTION #3008620 CONTROLLER #3011864 Installing Controller and Wiring 2. Insure no wires are nicked or damaged during installation. 3. Connect the 4-pin connecter on the wire harness to the control box. 4. Connect the 2-pin connector on the power cable to the control box. 5.
PAGE 5
Spreader Operation. Optional Vibrator Installation. 1. Due to the rate at which materials absorb moisture differently, some materials may not perform as desired. Therefore, the substitution of an alternative material may be necessary for optimum performance. 2. When filling hopper use only screened material. Prevent large chunks of material and debris from getting into hopper and cause operational problem or damage. 3. Material must never be left in the hopper for extended period of time.
PAGE 6
Hopper Assembly 22 23 13 12 10 11 4 9 5 1 7 6 14 15 2 24 3 25 8 17 18 20 19 21 16 Bill of Materials ITEM PART NO. QTY. 1 2 3 4 5 6 7 8 9 10 11 12 13 3024587 3024588 FCS025020150SS FNE025020031SS 3024591 3026097 3024590 3027511 FWF031075006SS 3006719 3026096 FWF025063007SS FCS025020100SS 1 1 1 6 1 1 1 3 3 3 1 13 5 DESCRIPTION GEAR MOTOR 12 VDC. DUAL SHAFT AUGER SCREW, HHC - 1/4-20 X 1-1/2 SS NUT, NYLON INSERT 1/4-20 SST RETAINER GEARMOTOR, CHUTE TROUGH TGS02 SLEEVE BEARING .
PAGE 7
Spreader Assembly 8 6 3 13 7 15 14 12 9 10 5 11 1 2 Bill of Materials ITEM PART NO. QTY.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.