Instructions / Assembly

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment10.79 cu.ft Tailgate Salt Spreader

Installation Instructions

TGS05B

Fig. 1 Mounting

—continued inside

SAFETY PRECAUTIONS

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By fol-

lowing these precautions and common sense, pos-

sible injury to persons and potential damage to

this machine may be avoided.

1. Read this entire Owners Manual before operat-

ing this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating

this spreader.

4. Do not adjust, clean, lubricate or unclog material

jambs without first turning off the spreader.

5. Make sure the spreader is securely fastened to

the vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of

maintenance or repairs.

7. Always disconnect the battery before removing

or replacing electrical components.

SPREADER ASSEMBLY

Check contents of box against parts list to make

sure all components are included. When ordering

replacement or spare parts refer to parts list for

part numbers.

INSTALLATION

1. Locate and mark center of tailgate.

2. Assemble Angles (18, 19) and Braces (20) as

shown in Fig.1 Use 3/8" carriage bolts, flat washers

and nuts. Do not tighten fasteners at this moment.

3. Center assembly on top of tailgate. Lower angle

must be flush with top and inside surfaces of

tailgate.

4. Position braces (20) on top of side rails. Using

holes in braces as guides mark and drill holes for

3/8" screws.

5. Attach braces to side rails using 3/8" screws,

flat washers and nuts.

6. Center spreader assembly on top of rear

bumper and align with holes in Angle (18).

7. Using holes in spreader frame as guides, mark

and drill holes for 3/8" screws in rear bumper.

8. Assemble spreader to Angle (18) and rear

bumper. Adjust position of Angles (18, 19) to bring

spreader into vertical position. Tighten all screws

at this moment.

Chart A Torque

1/4-20 6.0

5/16-18 11.0

3/8-16 20.0

BOLT NUT SIZE TORQUE (FT-LBS)

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Installation Instructions TGS05B SAFETY PRECAUTIONS WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1. Read this entire Owners Manual before operating this spreader. 2.
PAGE 2
TM ELECTRICAL INSTALLATION Observe spinner direction of rotation. The correct direction is counter clock wise when looking inside hopper from the top. If direction is clock wise reverse wires between Motor and Wire Harness. IMPORTANT! Make sure all wires are securely attached to vehicle or spreader’s frame. Use wire ties and/or wire clamps to attach wires. All excess wires must be rolled into bundles and attached to vehicle or spreader.
PAGE 3
TM Bill of Materials item part no. qty.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Wiring Diagram MOTOR PART #3009476 OPTIONAL VIBRATOR PART #3008076 4-PIN CONNECTOR FUSE CONNECTOR CONNECTOR TO FUSE TERMINAL OR IGNITION SWITCH WIRE HARNESS PART #3008620 BATTERY POWER CABLE PART #3008615 2-PIN CONNECTOR CONTROLLER PART #3008623 10 6 1 11 7 12 9 3 Fig. 4 2 Bill of Materials item part no. qty.