Instructions / Assembly

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment11 cu. ft. Black Poly Tailgate Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

TGS07 Salt Spreader

TGS07RED Salt Spreader

TGS07YEL Salt Spreader

US PATENT 8,888,025; 9,562,333

other PATENTS PENDING

Serial Number 01700 and Higher

—continued inside

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By following these

precautions and common sense, possible injury

to persons and potential damage to this machine may be

avoided.

SPREADER WARRANTY

This warranty replaces all previous warranties and

no employee of this company is authorized to extend

additional warranties, or agreements, or implications not

explicitly covered herein.

Buyers Products Company warrants all parts of

the product to be free from defects in material and

workmanship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including modifications,

misuse, accident, or lack of maintenance will not be

considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing any

part(s), which are returned, prepaid, 30 days after such

defect is discovered, and returned part(s) are found to be

defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from whom

purchased.

Buyers Products Company shall not be liable for damage

arising out of failure of any unit to operate properly,

or failure, or delay in work, or for any consequential

damages. No charges for transportation or labor

performed on any part will be allowed under this warranty.

Safety Precautions

1. Read this entire Installation Instruction before oper-

ating this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating this

spreader.

4. Do not adjust, clean, lubricate or unclog material

jams without first turning off the spreader.

5. Make sure the spreader is securely fastened to the

vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of mainte-

nance or repairs.

7. Always disconnect the battery before removing or

replacing electrical components.

Spreader Assembly

Check contents of box against parts list to make sure

all components are included. When ordering replace-

ment or spare parts refer to parts list for part numbers.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Installation Instructions TGS07 Salt Spreader TGS07RED Salt Spreader TGS07YEL Salt Spreader US PATENT 8,888,025; 9,562,333 other PATENTS PENDING Serial Number 01700 and Higher Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader.
PAGE 2
TM 1. Slide frame #3015859 into hitch receiver. Fig.1. Fig. 1 2. Slide hopper assembly #3015380 between frame uprights with front portion rested on the truck’s bumper. Fig.2. Fig.
PAGE 3
TM 5. Assembly ½-13 x 6.0 screws with flat washers and ½-13 flanged nuts and nylock nuts as shown in Fig.5. Make sure that nuts located between hopper side brackets and frame positioned exactly as shown. These nuts must not be in contact with brackets and frame at this time. 3. Align holes in rear portion of the hopper with slots in frame uprights. Use slots which will position spreader with a slight upward tilt. Secure hopper assembly to frame using ½-13 x 3.0 screws, flat washers and nuts. Fig.3.
PAGE 4
TM 7. Attach shield #3015707 to trough bracket as shown in Fig.7 9. Attach spinner disk to gear motor shaft as shown in Fig.9. Secure disk on shaft using clevis pin and cotter pin. Fig. 9 Fig. 7 3019561 SCREW 3/8-16 X 1.0 CLEVIS PIN 1420014 COTTER PIN FPC007800075 WASHER FLAT 3/8 10. Install lid #3015926 on to hopper. Place lid on hopper. Bend hinges outward from center of the hopper. Slide hinges openings on round protrusions of the lid. Repeat this operation on opposite side of the hopper.
PAGE 5
TM THIS IS WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK’S FRAME OR BODY ALLOWED! CAUTION DO NOT MOUNT CONTROLLER IN THE WAY OF AIR BAG DEPLOYMENT! NOTE: Always disconnect battery before attempting to install electrical components on your vehicle. Mount the controller in a convenient location in the truck cab. It is recommended not to mount the controller directly in front of heat vents. Allow ample air space around controller.
PAGE 6
TM Spreader Operation. Maintenance Instructions. 1. Due to the rate at which materials absorb moisture differently, some materials may not perform as desired. Therefore, the substitution of an alternative material may be necessary for optimum performance. 2. When filling hopper use supplied screen to prevent large chunks of material and debris contained in the material to get into hopper and cause operational problem or damage. 3. Material must never be left in the hopper for extended period of time.
PAGE 7
TM Tailgate Auger 4 8 1 5 2 Bill of Materials 3 6 ITEM 1 2 3 4 7 5 TGS07 Hopper Assembly 9 1 ITEM 10 1 HOPPER ASSEMBLY, TGS07 DESCRIPTION 3026561 1 HOPPER ASSEMBLY, RED 3026563 1 HOPPER ASSEMBLY, YELLOW 3015859 1 FRAME, HITCH MOUNT 3020207 1 HARDWARE BOX TGS07 3015926 1 LID, TGS07 3026566 1 LID, RED 3026567 1 LID, YELLOW 3015707 1 SHIELD TGS07 6 3019561 1 SPINNER, 12 IN TGS 7 3018923 1 DISC PROTECTOR 8 3018781 1 SCREEN TGS07 15 14 13 19 7 12 20 18 5 6
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM TGS07 Trough Assembly 9 4 3 Bill of Materials 2 6 7 5 8 13 12 15 14 1 10 11 TGS07 Hardware Box ITEM PART NO. QTY.