User Manual

ManualsBrandsSaltDogg ManualsCarTGS07YEL Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

TGS07 Salt Spreader

TGS07RED Salt Spreader

TGS07YEL Salt Spreader

Serial Number 01700 and Higher

—continued inside

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By following

these precautions and common sense, possible injury

to persons and potential damage to this machine may be

avoided.

SPREADER WARRANTY

This warranty replaces all previous warranties and

no employee of this company is authorized to extend

additional warranties, or agreements, or implications

not explicitly covered herein.

Buyers Products Company warrants all parts of

the product to be free from defects in material and

workmanship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including

modifications, misuse, accident, or lack of maintenance

will not be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing

any part(s), which are returned, prepaid, 30 days after

such defect is discovered, and returned part(s) are

found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from

whom purchased.

Buyers Products Company shall not be liable for

damage arising out of failure of any unit to operate

properly, or failure, or delay in work, or for any

consequential damages. No charges for transportation

or labor performed on any part will be allowed under

this warranty.

Safety Precautions

1. Read this entire Installation Instruction before

operating this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating this

spreader.

4. Do not adjust, clean, lubricate or unclog material

jams without first turning off the spreader.

5. Make sure the spreader is securely fastened to

the vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of main-

tenance or repairs.

7. Always disconnect the battery before removing or

replacing electrical components.

Spreader Assembly

Check contents of box against parts list to make

sure all components are included. When ordering

replacement or spare parts refer to parts list for part

numbers.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Installation Instructions TGS07 Salt Spreader TGS07RED Salt Spreader TGS07YEL Salt Spreader Serial Number 01700 and Higher Safety Precautions WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1.
PAGE 2
TM 1. Slide frame #3015859 into hitch receiver. Fig.1. Fig. 1 2. Slide hopper assembly #3015380 between frame uprights with front portion rested on the truck’s bumper. Fig.2. Fig.
PAGE 3
TM 3. Align holes in rear portion of the hopper with slots in frame uprights. Use slots which will position spreader with a slight upward tilt. Secure hopper assembly to frame using ½-13 x 3.0 screws, flat washers and nuts. Fig.3. Do not tighten fasteners at this time. 4. Slide hopper and frame towards tailgate leaving about 3/8” to ½” space. Align closest holes in hitch receiver with holes in frame. Secure frame in hitch receiver using 5/8 hitch pin and cotter pin. Fig.4.
PAGE 4
TM 8. Attach spinner protector #3018923 to spreader frame as shown in Fig.8. 7. Attach shield #3015707 to trough bracket as shown in Fig.7 Fig. 7 SCREW 3/8-16 x 2.0 3018923 SPINNER PROTECTOR SCREW 3/8-16 X 1.0 WASHER FLAT 3/8 Fig. 8 WASHER FLAT 3/8 NUT 3/8-16 NUT NYLOCK 3/8-16 SHIELD #3015707 9. Attach spinner disk to gear motor shaft as shown in Fig.9. Secure disk on shaft using clevis pin and cotter pin. 10. Install lid #3015926 on to hopper. Place lid on hopper.
PAGE 5
TM THIS IS WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK’S FRAME OR BODY ALLOWED! CAUTION DO NOT MOUNT CONTROLLER IN THE WAY OF AIR BAG DEPLOYMENT! NOTE: Always disconnect battery before attempting to install electrical components on your vehicle. Mount the controller in a convenient location in the truck cab. It is recommended not to mount the controller directly in front of heat vents. Allow ample air space around controller.
PAGE 6
TM Spreader Operation. Maintenance Instructions. 1. Due to the rate at which materials absorb moisture differently, some materials may not perform as desired. Therefore, the substitution of an alternative material may be necessary for optimum performance. 2. When filling hopper use supplied screen to prevent large chunks of material and debris contained in the material to get into hopper and cause operational problem or damage. 3. Material must never be left in the hopper for extended period of time.
PAGE 7
TM Tailgate Auger 4 8 1 5 2 Bill of Materials 3 6 ITEM 1 QTY. 1 HOPPER ASSEMBLY, TGS07 DESCRIPTION 3026561 1 HOPPER ASSEMBLY, RED 3026563 1 HOPPER ASSEMBLY, YELLOW 2 3015859 1 FRAME, HITCH MOUNT 3 3020207 1 HARDWARE BOX TGS07 3015926 1 LID, TGS07 3026566 1 LID, RED 3026567 1 LID, YELLOW 5 3015707 1 SHIELD TGS07 6 3019561 1 SPINNER, 12 IN TGS 7 3018923 1 DISC PROTECTOR 8 3018781 1 SCREEN TGS07 4 7 PART NO.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM TGS07 Trough Assembly 9 4 3 Bill of Materials 2 6 7 5 8 13 12 15 14 1 10 11 TGS07 Hardware Box ITEM PART NO. QTY.