Replacement Part List

ManualsBrandsSaltDogg ManualsKitchenLight Commercial Electric Poly SUV Tailgate Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

TGSUVPROA Salt Spreader

—continued inside

WARNING

Observe the following Safety Precautions before,

during and after operating this spreader. By following

these precautions and common sense, possible injury to

persons and potential damage to this machine may be

avoided.

Safety Precautions

1. Read this entire Owners Manual before

operating this spreader.

2. Read all safety decals on the spreader before

operating.

3. Verify that all personnel are clear of the

spreader spray area before starting or operating this

spreader.

4. Do not adjust, clean, lubricate or unclog material

jambs without first turning off the spreader.

5. Make sure the spreader is securely fastened to the

vehicle in accordance with this manual.

6. Do not operate a spreader that is in need of mainte-

nance or repairs.

7. Always disconnect the battery before removing or

replacing electrical components.

Spreader Assembly (fig. 1)

Check contents of box against parts list to make

sure all components are included. When ordering

replacement or spare parts refer to parts list for part

numbers.

Tools Needed for Assembly

• 3/8 or 1/2 drive ratchet with 3/8, 7/16, 1/2, 9/16

and 15/16 sockets

• 7/16, 1/2, 9/16 & 15/16 wrench

• 1/8" Allen wrench

SPREADER WARRANTY INFORMATION

This warranty replaces all previous warranties and no

employee of this company is authorized to extend addi-

tional warranties, or agreements, or implications not

explicitly covered herein.

Buyers Products Company warrants all parts of the prod-

uct to be free from defects in material and

workmanship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including

modifications, misuse, accident, or lack of maintenance

will not be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or

replacing any part(s), which are returned, prepaid, 30

days after such defect is discovered, and returned part(s)

are found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from whom

purchased.

Buyers Products Company shall not be liable for

damage arising out of failure of any unit to operate prop-

erly, or failure, or delay in work, or for any

consequential damages. No charges for transportation

or labor performed on any part will be allowed under this

warranty.

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions TGSUVPROA Salt Spreader Tools Needed for Assembly • 3/8 or 1/2 drive ratchet with 3/8, 7/16, 1/2, 9/16 and 15/16 sockets • 7/16, 1/2, 9/16 & 15/16 wrench • 1/8" Allen wrench Safety Precautions WARNING SPREADER WARRANTY INFORMATION Observe the following Safety Precautions before, during and after operating this spreader.
PAGE 2
Spinner Shield & Receiver Mount (fig. 2) 1. Slide 2" receiver mount (3) into receiver hitch. Secure it with hitch pin (9) 2. Mount motor/frame assembly to the receiver mount by inserting 5/8" bolt and nut (10, 11) in the bottom hole and hitch pin in the top hole of the receiver mount. Frame position is adjustable. 3. Install spinner shield (5) with 3/8-16 x 1 hex screws, flat washers and nuts (12, 13 and 17). Position shield ½" away from spinner. Shield position is adjustable. Fig.
PAGE 3
Electrical Installation (fig. 5) THIS IS WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK’S FRAME OR BODY ALLOWED! 2 WARNING WARNING! Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. To insure good performance of your spreader, check the condition of truck’s electrical system. Using digital voltmeter, check alternator and battery voltage. With engine running and head lights and heater fan ON good voltage reading should fall between 13.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Spreader Maintenance 8. Connect the wire harness to the motor. Thoroughly clean battery terminals. Make sure battery terminals have no tarnish or corrosion. DO NOT CONNECT WIRE HARNESS TO DAMAGED OR CORRODED TERMINALS! IT MAY RESULT IN OVERHEATING, LOST POWER AND POTENTIAL CONTROLLER DAMAGE! 9. Connect the power cable directly to the battery. 10.