Replacement Part List

2
1
10
11
3
9
12
17
5
13
1
2
3
4
5
21
22
23
24
25
Spinner Shield & Receiver Mount (fig. 2)
1. Slide 2" receiver mount (3) into receiver hitch.
Secure it with hitch pin (9)
2. Mount motor/frame assembly to the receiver mount
by inserting 5/8" bolt and nut (10, 11) in the bot-
tom hole and hitch pin in the top hole of the receiver
mount. Frame position is adjustable.
3. Install spinner shield (5) with 3/8-16 x 1 hex screws,
flat washers and nuts (12, 13 and 17). Position shield
½" away from spinner.
Shield position is adjustable.
Bill of Materials
1 3017107 1 MOTOR, FRAME ASSY,TGSUVPROA
2 3013283 1 HOPPER, W/ GRAPHICS MOLDED SALT DOGG
3 3004589 1 REC. MOUNT, SWING DOWN, TGSUV1 WELDMENT
4 3003571 1 LID, TGSUV1
5 3005977 1 SHIELD, SPINNER, TGSUV1A
6 3006943 1 DECAL, MODEL ID/DATE, TGSUVPROA
7 3014780 1 HARDWARE BAG TGSUVPRO
8 3005714 1 HARDWARE BAG ASSEMBLY, TGSUV1A
9 HP6253WC 2 HITCH PIN WITH HP COTTER
10 3000544 1 SCREW, HH CAP 5/8-11X3.5 GR.5 ZINC
11 FNE063011069 1 NUT, NYLOCK 5/8-11, ZN
12 FCS038016100SS 4 SCREW, HHC 3/8-16 X 1 304 SST
13 FNE038016044SS 6 NUT, NYLOCK 3/8-16 X 7/16 SST
14 3000626P 2 KEEPER, LATCH WJ201 BLACK
15 FBSH01002475SS 8 SCREW, BHC #10-24 X .75 SST
16 FNE010024024SS 8 NUT, ELASTIC STOP 10-24 SS
17 FWF038100007SS 8 WASHER, FLAT 3/8 USS SST
18 3002982 2 STRAP, HOOD CATCH, BLACK
19 3007068 2 CAP SCREW, HX HD-3/8-16X3 SST
20 3007115 4 WASHER, FLAT 3/8 X 1.5 X.048 SST
21 3011864 1 CONTROLLER TGS W/ VIBRATOR SWITCH
22 3035934 1 WIRE HARNESS, POWER TGS
23 3008620 1 WIRE HARNESS MAIN W/ VIBRATOR, TGS
24 3001379 1 CABLE, BATTERY
25 3015788 1 RETAINER HOPPER TGSUV
26 CB50PB 1 CIRCUIT BREAKER
ITEM PART NO. QTY. DESCRIPTION
Fig. 1
Hopper and Retainer (fig. 3)
1. Slide the hopper onto the sleeve below until the
holes in the hopper line up with the holes in the frame
tube.
2. Install hopper retainer (25) using two 3/8-16 x 3 hex
cap screws (19) and two 3/8-16 x 1 hex cap screws
(12) from the outside of the retainer through the
retainer, tube and hopper. Install 4 large flat washers
(20) inside hopper and 4 smaller 3/8 flat washers (17)
outside retainer. Secure hopper to frame with 4 3/8-16
nuts (13).
Fig. 2