User Manual SAMCOM FPCN30A Features ■ With GROUP button ■ Voice commander/scrambler ■ 20 Memory Channel ■ VOX Sensitive settings ■ With LCD Display ■ Key Lock and Tone Setting ■ Squelch tail elimination Sancon Inc.
User Security Information Handheld transceiver product safety and RF radiation Warning: Please read the manual carefully before using. It contains the important safety using operation instruction, and RF energy and control information contributing to meet the RF radiation limitation requirement of national and international standards. Information provided in this manual may replace the general safety information of the editions before.
Electromagnetic Interference / Electromagnetic Compatibility Remark: Electromagnetic Interference (EMI) occurs in nearly every electronic equipment, by not enough shielding, improper design or incorrect electromagnetic compatibility configuration. Not allowed to change the transmitting frequency, to increase the transmission power (including the installation of additional RF power amplifier). Not allowed to use an external antenna or other transmitting antenna.
Safe Driving Check your car seat using the transceiver the relevant laws and regulations, and follow the regulations. If you use the transceiver while driving, please note the following: Concentrate on driving, pay attention to the situation of the road. If possible, try to use the walkie-talkie-free function operation. If the provision of using the transceiver while driving prohibited, please drive the car to the roadside stop, and then make a call.
Notes Antenna Caution Not use the handheld transceiver with damaged antenna. It will cause skin mild burns if touch the damaged antenna. Battery If some of your body exposed conductive material contact the battery outside terminals, it will cause damage to property, or burns on human body. These conductive materials include jewelry, keys, or beaded necklace, they will form a loop with the battery (causes short circuit), generate considerable heat.
Get Familiar with the transceiver (1) PTT Transmitting (2) MONI (monitor) button (3) Scan/call button (4) Antenna (5) Channel selection knob (6) Power/volume switch (7) Speaker (8) Microphone (9) Status indicator (10) Battery release button (11) Earphone cap (12) LCD Display (13) Keys (14) Battery (15) Belt screw (16) Charger 4 6 15 5 1 2 9 7 11 12 8 3 10 13 14 16 Press the MENU key,enter into the menu selecting modePress ▲ or ▼ key choice the function.
Channel Number Battery Capacity Transmit Frequency CDCSS Receive Frequency CTCSS Transimitting status Receiving status Group Call Status Battery Information Battery on First Use Since batteries leave factory without a fully charging, please charge the new batteries before using. Under normal circumstances, the battery on first use needs 5 hours of charging. The first three times of fully charging and discharging provides batteries the best capacity.
Extension of Battery life 1. The performance of the battery will be reduced when the temperature drops below 0℃. In cold weather, it is advised to spare another battery for emergency. Please do not dispose the cold batteries that can not work at low temperature but may be usable at room temperature. 2. It may affect the normal use or charge of the battery, if it is covered with dust. Please clean the battery with dry cloth before loading or charging it. Knowledge about Battery Storage 1.
Installation/Removal of the Battery 1. Installation of the Battery Please make sure the transceiver is powered off, and then hold down the belt clip to open it , Hold down the two side keys and insert the two bumps on the top of the battery into the aluminum grooves of the transceiver in the direction of the arrow, and to finish the installation, press the bottom of the battery in the direction of the arrow until the “ka-ta” sound is heard.
2. Removal of the belt clip As for the removal of the belt clip, please refer to the installation steps and loose the screws in counterclockwise. Installation/Removal of External Earphone or Microphone 1. Installation of the external earphone or microphone (1) Unclose the earphone cap (without removing) in the direction of the arrow (2) Insert the earphone or microphone 2. Removal of the external earphone or microphone You can pull out the external earphone or microphone to remove it.
1、GRP (Group Channel) Setting After pressing MENU into function menu and GRP will be shown on display, press OK key then you can select 0-19 through by ▲or ▼, then press OK key again the new GRP channel is fix. press the EXIT key to give up setting 2、VOX Setting After pressing MENU into function menu and choice VOX, press OK key then you can select 1-9 and off through by ▲ or ▼, then press OK key again, press the EXIT key to give up setting. Level 9 small voice can open transimt.
Channel Adjustment Channel knob clockwise to decrease the channel number, or counterclockwise to increase it. Monitoring To monitor, you need just hold down the MONI button and adjust the channel background noise to a comfortable level by rotating the PWR/VOL knob. It can directly monitor the channel you care without having to wait for your call, as long as the MONI button has been hold down.
This feature is designed to trigger the transmitting of voice by voice itself. Users can choose to turn on or off the VOX feature, and set the sensitivity of VOX through Meun. With this feature, transmitting operation is launched by the voice you said without having to press the PTT button. The transmitting operation stops as soon as the end of the talk. Voice compression and expansion This feature ensures the user in a variety of noisy environments can get a clear call.
Maintenance and Cleaning 1. Do not lift the transceiver directly by its antenna or external microphone. 2. Dust the transceiver with an anti-pilling cloth to prevent bad contact. 3. When the transceiver is off work, please cover the microphone cap. 4. The buttons, control knob and the casing of transceiver are easy to become dirty after long usage, you can use a neutral detergent (do not use strong corrosive chemicals) and wrung damp cloth to clean it.