WIRELESS MICROPHONE SYSTEM
WARNING TO PREVENT FIRE OR SHOCK HAZARD. DO NOT USE THIS PLUG WITH AN EXTENON CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PRESENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PRVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT FULLY INSERT.
ATTENTION: Pour éviter tout risque d’électrocution ou d’incendie, ne pas exposer cet appareil à la pluie ou à l’humidité. Pour éviter tout risque d’électrocution, ne pas ôter le couvercle ou le dos du boîtier. Cet appareil ne contient aucune pièce remplaçable par l'utilisateur. Confiez toutes les réparations à un personnel qualifié. Le signe avec un éclair dans un triangle prévient l’utilisateur de la présence d’une tension dangereuse et non isolée dans l’appareil.
PRECAUCION: Para reducir el riesgo de incendios o descargas, no permita que este aparato quede expuesto a la lluvia o la humedad. Para reducir el riesgo de descarga eléctrica, nunca quite la tapa ni el chasis. Dentro del aparato no hay piezas susceptibles de ser reparadas por el usuario. Dirija cualquier reparación al servicio técnico oficial.
Copyright 2008-2009, Samson Technologies Corp. v2.1 Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.
Table of Contents Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 QuickStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Guided Tour - AR300 Receiver / Front Panel . . . . . . 10-11 Guided Tour - AR300 Receiver / Rear Panel . . . . . . . . .12 Guided Tour - AX300 Transmitter . . . . . . . . . . . . . 13-14 Setting Up and Using Your AirLine Synth system . .
Introduction Welcome to Samson AirLine Synth—the next generation of wireless systems! Wireless microphone and instrument systems were originally developed to eliminate cables, providing unparalleled freedom of movement. AirLine Synth takes this concept to a new level with transmitters so small, lightweight and aerodynamic, they are nearly invisible, providing a completely “hassle-free” user experience.
QuickStart If you’ve had some prior experience using wireless systems, these QuickStart instructions will get you up and running with your AirLine UHF microphone system in a matter of minutes! Detailed instructions for setting up and using your AirLine Synth system can be found on page 15 of this manual, and the “Guided Tour” sections on pages 10- 14 provide full descriptions of all AirLine component controls and displays. 1.
QuickStart 7. Now to set the channel, press and hold the EDIT control until the display shows the group number with three asterisks. Next, the AR300 will automatically find the clearest channel and you will see it in the Channel number of the display just before the IR SET will begin. 8. Once you see the IR SET flashing in the LCD display, hold the transmitter, with the bottom of the AX300 facing towards the AR300, approximately 6 inches away from the receiver and turn the AX300 power switch on.
Guided Tour - AR300 Receiver / Front Panel 1. Antennas (A and B) - The antenna mountings allow full rotation for optimum placement. In normal operation, both Antenna A (the antenna on the left) and Antenna B (the antenna on the right) should be placed in a vertical position. Both antennas can be folded inward for convenience when transporting the AR300. See the “Setting Up and Using Your AirLine Synth System” section on page 15 in this manual for information about antenna installation and positioning.
Guided Tour - AR300 Receiver / Front Panel 6: EDIT Control – This rotary encoder control knob is used to control and set several menu functions and parameters displayed in the LCD display and it is also used to preform the automatic Channel Scan. 7: Power Switch - Use this to turn the AR300 power on and off. When the receiver is on, the LCD backlight is lit. 8: IR Transmitter – During “IR SET” an Infrared light is used to set the transmitter channel.
Guided Tour - AR300 Receiver / Rear Panel A A B C E D A: Antenna socket - D hole knockout for mounting the antennas to the rear panel using the optional rear antenna kit. B: DC input - Connect the supplied power adapter here, using the strain relief as shown in the illustration below. WARNING: Do not substitute any other kind of power adapter; doing so can cause severe damage to the AR300 and will void your warranty.
Guided Tour - AX300 Transmitter 1: Plug - Insert this standard 3-pin XLR plug into your the included Samson Q7 or any dynamic microphone. 1 2: LCD Display – This three digit Liquid Crystal Display indicates the Absolute Channel number that the transmitter is set to. 4: IR Lens - This acrylic window is used to capture the infrared signal sent from the AR300 during the IR SET to channelize the AX300.
Guided Tour - AX300 Transmitter 8: Battery compartment Insert a standard AA alkaline battery here, being sure to observe the plus and minus polarity markings shown. We recommend the Duracell type battery. Although rechargeable Ni-Cad batteries can be used, they do not supply adequate current for more than four hours. WARNING: Do not insert the battery backwards; doing so can cause severe damage to the AX300 and will void your warranty.
Setting Up Your AirLine Synth System The basic procedure for setting up and using your AirLine Synth system takes only a few minutes: 1. Remove all packing materials (save them in case of need for future service) and check to make sure that the supplied power adapter is the correct voltage for your country. If not, contact your distributor or, if purchased in the United States, Samson Technical Support at 1-800-372-6766. 2. Physically place the AR300 receiver next to your mixer.
Setting Up Your AirLine Synth System 6. Make the physical cable connection between the AR300 output jack and an audio input of your mixer. Leave your mixer and power amplifier off at this time. 7. Turn the Level knob on the AR300 completely counterclockwise, then set its Power switch up to turn it on. The LCD display light will illuminate. 8. Now to set the channel, press and hold the EDIT control until the display reads CH SCAN.
Setting Up Your AirLine Synth System 12. Temporarily turn down the level of your mixer or amplifier and turn off the power to your transmitter, leaving the AR300 receiver on. Then restore the previously set level of your mixer or amplifier. With the transmitter off, the receiver output should be totally silent; if it is, skip ahead to the next step. If it isn’t (that is, if you hear some noise), you may need to adjust the AR300 Squelch control.
AR300/AX300 Operation Setting a Group and Channel Manually The AR300 receiver contains 320 selectable channels for N and U band, and 71 selectable channels for E band. All channels are organized into a series of groups. Each group contains channels that are compatible for simultaneous use. When using multiple systems, each system should be assigned to the same group in order to maximize the number of compatible channels.
AR300/AX300 Operation Operating In FREE Mode You can tune in an exact frequency using the AR300’s FREE mode. Once you are in FREE mode you can change the frequency by 25 kHz steps. For most situations, it’s better to use the GROUP channel plan but if you application requires an exact frequency, follow these steps to operate in FREE mode. 1. Press the EDIT controller three times until the display’s FREE icon turns on and Frequency number flashes. 2.
Specifications SYSTEM SPECIFICATIONS Channels 320 channels 25kHz Step (N and U Bands) 71 channels 25kHz Step (E Band) Operating Frequency 639.025–647 MHz 798.
Specifications TRANSMITTER (AX300) Oscillation Type Crystal-controlled PLL frequency systhesized Modulation Type FM Antenna 1/4 Wave Length Dipole Type Input Impedance 290k ohms(ATT:0dB), 330k ohms(ATT:-15dB) Maximum Input Level -2dBv Switches/Controls POWER switch, MUTE switch, GAIN control Display CHANNEL (LCD), BATT (LED) Interface Infrared Impedance 2.2k ohms Battery AA x 1 Current Consumption Less than 120mA Operating Voltage 1.2V-1.
FCC Rules and Regulations Samson wireless systems are type accepted under FCC rules parts 90, 74 and 15. Licensing of Samson equipment is the user’s responsibility and licensability depends on the user’s classification, application and frequency selected. This device complies with RSS-210 of Industry & Science Canada.
EC Declaration of Conformity 0979 We, Samson Technologies Corporation, located at 45 Gilpin Ave, Hauppauge, NY 11788 USA declare under our own responsibility that the Products: Equipment: Wireless Microphone System Model #: Samson AirLine Synth - AR300 Receiver & AL300 / AX300 / AG300 Transmitters are in conformity with the essential requirements of the following EC Directive(s) when installed in accordance with the installation instructions contained in the product documentation: 73/23/EEC LVD Directive
Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.
