Install drivers Install programs SyncMaster 204T
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Put your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause an electric shock or fire inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf. z Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area.
Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or back).
Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor.
Adjust the resolution and frequency to the levels appropriate for the model. z Inappropriate resolution may cause undesirable picture quality. 20 inch - 1600 X 1200 Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
D-Sub Cable Power Cord DVI Cable Set-Bracket Sold separately Screws (4EA) Front Menu button [ ] Brightness button [ ][ ] Enter button [ ] / Source button Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. Adjust items in the menu. / When OSD is not on the screen, push the button to adjust brightness. >>Click here to see an animation clip Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off.
to the graphic card's DVI port using the DVI cable. Auto button When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.
POWER S/W : Switch the monitor on and off. POWER IN : Power cord, plugs into monitor and wall receptacle. DVI port : Connect the DVI cable to the DVI port on the back of your monitor. (SOURCE : digital) D-sub 15-pin port : Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. (SOURCE : analog) Kensington Lock : The Kensington lock is a device used to physically fix the system when using it in a public place.
(The locking device has to be purchased separately. ) Stand Height Adjustment - Press the top side of the stand and then push the button at the rear bottom of the stand. - You can adjust the stand height using this button. When you are using a stand height as maximum , it will go down a little bit from spring elasticity. See Connecting the Monitor for further information regarding cable connections.
Connecting the Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI port on the back of your monitor. 2-3. Connected to a Macintosh.
Using the Stand Removing the base 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws(A) and then remove the Stand from the LCD monitor. Attaching a Base This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2.
Installing the Monitor Driver (Automatic) When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.
Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung.com/. 5. Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor.
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced..". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.
Natural Color Natural Color Software Program One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
1. Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 2. These buttons allow you to adjust items in the menu. 3. Press this button to activates a highlighted menu item. 4. Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically. 5. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Menu OSD Lock & Unlock Description After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). MagicBright™ Menu MagicBright™ Brightness Description Push the MagicBright button to circle through available preconfigured modes.
Menu Description When OSD is not on the screen, push the button to adjust brightness. Brightness SOURCE Menu SOURCE Description Selects the video signal while the OSD is off.
Menu Description Play/Stop You can use the on-screen menus to change the brightness according to personal preference. Brightness Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness. Contrast You can use the on-screen menus to change the contrast according to personal preference.
Color Tone Color Control The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. Adjusts individual R,G,B color balance. Select one of three pre-defined gammas. Gamma z z z Mode 1 : Shows normal gamma Mode 2 : Shows lower gamma (darker) Mode 3 : Shows higher gamma (brighter) Image Menu Description Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area.
OSD Menu Description You can choose one of eight languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Auto Source Select Auto Source for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values.
Information Shows a video source, display mode on the OSD screen.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune program. 7. Click "Install." 8. The "Installationation Status" window appears.
9. 10. Click "Finish." When the installation is complete, the MagicTune executable icon appears on your desktop. Double-click the icon to start the program. Magictune execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installationation Problems The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
OS z z z z z Windows Windows Windows Windows Windows 98 SE Me 2000 XP Home Edition XP Professional Hardware z z 32MB Memory above 25MB Hard disk space above * For more information, visit the MagicTune website.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of Magictune Program may not operate normally.
in the control window, clicking "Cancel" does not cause any actions. Picture Tab Definition Allows the user to adjust the screen settings to the desired values. j Resolution n k l m i Brightness n j k l m n j Contrast n k l m j MagicBright k l m Brightness Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.
Color Tab Definition Adjusts the "warmth" of the monitor background or image color. MagicColor and Gamma will be shown only in the monitor that supports these functions. j MagicColor n k l m i Color Tone n j k l m n j Color Control n k l m j Calibration n k l m j Gamma k l m The tone of the color can be changed. z z Warm2 - Warm1 - Cool 1 - Cool 2 - Cool 3 - Cool 4 - Cool 5 - Cool 6 - Cool 7 Off Color Tone Color Tone mode will be different according to monitor models.
{ The MagicZone ensures the clear and sharp display of animated multimedia or photo images by enhancing the brightness, sharpness, saturation, Hue of a certain area on the screen. This offers an easy-to-use interface that highlights the video-playing portion of your multimedia program by automatically detecting and highlight the desired area by dragging.
Image Tab Definition Adjusts the Fine , Coarse and Position values. i Image Setup n j k l m n j Position n k l m j Sharpness k l m z Image Setup z z Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu.
Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or off any Preference, position the cursor over the box and click. Preferences z z Source Select z z Enable task tray menu . - To access the MagicTune menus, click the icon on the [task tray menu]. The menus are not displayed if the [Enable System Tray] is deselected in [Options] ' [Basic Settings]. Select Language - The language chosen affects only the language of the OSD.
Version User Name Shows the user name that is registered in PC. User ID Shows the user ID that is register in PC. Server IP Write down the server IP . Department Write down the department. Location Write down the location. Displays the version of MagicTune.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. 2. 3. 4. 5.
Press "Preview" button on the Color Calibration. The above picture will be shown. 1. 2. Press "View Calibrated" button to see the calibration effect which you adjusted. Press "View Uncalibrated" button to see the original image.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune program can be removed only by using the "Add or Remove Programs" option of the Windows Control Panel. Perform the following steps remove MagicTune. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Troubleshooting z MagicTune may not work in case monitor is replaced or driver of graphic card is updated while MagicTune is operating. If so, please restart the system. Symptom Check List Check when MagicTune does not function properly. MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play.
Overview | Installation | Interface | Uninstall | Troubleshooting Overview What is MagicRotation? Traditionally, computer displays allowed the user to view only in landscape mode. In today's information age, more users need to view documents, web pages, emails, etc. in there day to day life. These types of applications can be better viewed in portrait mode where the entire contents are available on the screen.
Overview | Installation | Interface | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Installationation Status" window appears.
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installationation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation. Limitation 1.
{ Close the application. { Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the application. In most cases this should fix the problem. 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270). 5. Dual is not supported in Windows™ 98, ME, NT 4.0. 6.
Overview | Installation | Interface | Uninstall | Troubleshooting Interface The Menu on task bar Menu pop up at the mouse right button click. Rotate : Display will get rotated by the unit of 90 degree Rotate to 0 : Display will get rotated to 0 degree from the current angle of rotation. Rotate to 90 : Display will get rotated to 90 degree from the current angle of rotation.
Rotate to 180 : Display will get rotated to 180 degree from the current angle of rotation. Rotate to 270 : Display will get rotated to 270 degree from the current angle of rotation.
Hot key : Hot Keys are available by default and can be changed by user. It can be designated by user directly with keyboard after changing the existing HotKey instead . User can create the hot key with the combination of Shift, Ctrl, Alt and general keys. In case only general key is pressed, it will be designated in the form of Alt+general key. Help : It shows the HELP of MagicRotation program. About : It shows the version and copyright of program. Exit : It exits from MagicRotation program.
Overview | Installation | Interface | Uninstall | Troubleshooting Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add/Remove Programs" icon in Control Panel. 3.
Overview | Installation | Interface | Uninstall | Troubleshooting Troubleshooting Before You Call Technical Support z MagicRotation Software works with the installed "Display Driver" supplied by your Graphic Card Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly or has bugs in it, then these bugs would still exist even after MagicRotation Software is installed.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? (When connecting D-Sub cable) Check the signal cable connection.
display will work properly but the "Not Optimum Mode", "Recommended mode : 1600 X 1200 60Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press any key on the keyboard to activate the monitor and restore the image on the screen.
product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Have the Windows colors been set properly? Windows ME/2000/XP: Set the colors properly at the Control Panel → Display → Settings. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found".
Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel→Display→Settings. * Contact the video card manufacturer for details.
Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips z z A monitor recreates visual signals received from the computer.
General General Model Name SyncMaster 204T LCD Panel Size 20.1" Diagonal Display area 432mm (H) x 324mm (V) Pixel Pitch 0.255mm (H) x 0.255mm (V) Type a-si TFT/SPVA Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Colors Resolution Optimum resolution 1600 x 1200@ 60Hz Maximum resolution 1600 x 1200@ 60Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.
Dimensions (WxDxH)/ Weight 445 X 457.2 X 228.5 mm / 17.5 X 18 X 9.0 inch (With Stand) / 8.15kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature: 50°F ~ 104°F (10°C ~ 40°C) Humidity: 10% ~ 80%, non-condensing Storage Temperature: -4°F ~113 °F (-20°C ~ 45°C) Humidity: 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Frequency (kHz) Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA,1600X1200 75.000 60.000 162.000 +/+ IBM,640X350 31.469 70.086 25.175 +/- IBM,720X400 31.469 70.087 28.322 -/+ IBM,720X400 31.469 59.940 25.175 -/- VESA,640X480 37.861 72.809 31.500 -/- VESA,640X480 37.500 75.000 31.500 -/- MAC,640X480 35.000 66.667 30.240 -/- MAC,832X624 49.726 74.551 57.284 -/- VESA,800X600 35.156 56.250 36.000 +/-,+/- VESA,800X600 37.879 60.317 40.
Service The address and phone number of the company can be changed without prior notice. AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
ESPAÑA : Samsung Electronics Comercial Iberica, S.A. Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 08 25 08 65 65 Fax : 01 48 63 06 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. 16 64331 Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.
PANAMA : Samsung Electronics Latinoamerica( Z.L.) S.A. Calle 50 Edificio Plaza Credicorp, Planta Baja Panama Tel. : (507) 210-1122, 210-1133 Tel : 800-3278(FAST) http://www.samsung-latin.com/ PERU : Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru Tel: 51-1-336-8686 Fax: 51-1-336-8551 http://www.samsungperu.com/ PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.
Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) 242 0303 Fax. : (01952) 292 033 http://samsungservice.co.uk/ U.S.A : Samsung Electronics America Service Division 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) http://www.samsung.com/monitor/ Terms Dot Pitch The image on a monitor is composed of red, green and blue dots.
1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1600 X 1200 Vertical frequency (refresh rate): 60 Hz 2. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
