SyncMaster 400CXN,460CXN LCD Display User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock.
Safety Instructions Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Ensure that an authorized installation company installs the wall mount.
Safety Instructions Clean the product using a soft cloth with a LCD Display cleaner only. If you must use a cleaner other than the LCD Display cleaner, dilute it with water at a ratio of 1:10. When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire.
Safety Instructions When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. • Otherwise, this may result in electric shock or fire. If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the LCD Display by pulling only the wire or the signal cable.
Safety Instructions When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. If you continually move closer to the product screen, your eyesight may be failing. Take a rest for at least five (5) minutes after using the LCD Display for one (1) hour. This reduces the weariness of your eyes. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.
Safety Instructions Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid. The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Note This stand is not for the Floor Standing Type.
Introduction Others Remote Control Batteries (AAA X 2) Cleaning Cloth (Not available in all locations) Sold separately DVI Cable Wall Mount KIT LAN Cable Semi Stand KIT Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
Introduction Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [TV] D.
Introduction POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) DVI / PC / HDMI IN [HDMI] Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.
Introduction AV IN [VIDEO] (VIDEO Connection Terminal) AV AUDIO IN [L-AUDIO-R](LCD Display Audio Connection Terminal (Input)) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output)) COMMON INTERFACE This contains information on CAM inserted in the CI slot and displays it. When not inserting CI CARD in some channels, Scramble Signal is displayed onthe screen. You can install the CAM anytime whether the TV is ON or OFF.
Introduction Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model.
Introduction POWER OFF Number Buttons DEL button + VOL MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.MODE DUAL/MTS PIP SWAP 1. POWER Turns the product On. 2. Off Turns the product Off. 3. Number Buttons Press to change the channel.
Introduction 4. DEL button The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. 5. + VOL - Adjusts the audio volume. 6. Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. MUTE 7. TV/DTV Selects the TV and DTV mode directly. 8. Opens the on-screen menu and exits from the menu or closes the adjustment menu.
Introduction 24. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 25. EXIT Exits from the menu screen. 26. SRS Not Available. 27.MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is displayed on the lower center of the screen. AV / HDMI / TV : P.MODE The LCD Display has four automatic picture settings that are preset at the factory.
Introduction Mechanical Layout (400CXn) Mechanical Layout NETWORK MODEL SIZE
Introduction LCD Display Head NETWORK MODEL SIZE Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction When done, mount the wall bracket on the wall. There are two hinges(left and right). Use the correct one. 2. A- Captive Screw B- Wall Bracket C- Hinge (Left) D- Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A- 3.
Introduction To mount the product on the wall bracket The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same) 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice 3. • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Introduction LCD Display Head NETWORK MODEL SIZE Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Introduction 2. A- Captive Screw B- Wall Bracket C- Hinge (Left) D- Hinge (Right) Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A- 3. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm.
Introduction 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3.
Introduction A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. 3. You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display.
Connections Connect the audio cable for your LCD Display to the audio port on the back of your computer. Note • Turn on both your computer and the LCD Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power.
Connections • When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. • To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. 2. Turn on the LCD Display. 3. Select TV using the TV / DTV. 4. Select a desired TV channel. Note Is weak signal causing poor reception? Purchase and install a signal amplifier for better reception.
Connections 1. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [R-AUDIO-L] port of the LCD Display. 2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 3. Select AV using the SOURCE . Note The LCD Display has AV connection terminals to connect AV input devices like DVDs, VCRs or Camcorders. You may enjoy AV signals as long as the LCD Display is turned on. Connecting to a Camcorder 1. Locate the A/V output jacks on the camcorder.
Connections • You cannot connect a PC to the HDMI terminal. Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the HDMI terminal of the LCD Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVI-D AUDIO IN terminal of the LCD Display.
Connections Note Connect the LAN cable. Connecting a USB device Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When unwiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCR's or camcorders as well as your computer can be connected to the LCD Display.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings...". 5. Click "Properties" in the "Monitor" tab.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location..." then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software Installation MagicInfo Pro Installation 1. Insert CD into the CD-ROM drive. 2. Click the MagicInfo Pro installation file. 3. When the Install Shield Wizard window appears, click "Next." 4. Select "I agree to the terms of the license agreement" to accept the terms of use. 5. You are required to log in to the MagicInfo Pro Server program. Please enter the password to login. The password cannot be changed when you are logged in.
Using the Software 6. Choose a folder to install the MagicInfo Pro program. 7. Click "Install.
Using the Software 8. The "Setup Status" window appears. 9. It is recommended restarting the system for the normal operation of the MagicInfo Pro Server program. Click "Finish.
Using the Software 10. When the installation is complete, the MagicInfo Pro executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Minimum CPU RAM Ethernet OS P1.8 256M 100M/1G Windows XP WMP 9 or Windows later 2000 (Service Pack 4) Recommen- P3.
Adjusting the LCD Display Input Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. HDMI 5. MagicInfo 6. TV Note • The direct button on the remote control is the 'SOURCE' button. • For PC and DVI, this is deactivated if the cable is disconnected.
Adjusting the LCD Display → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. 1. PC 2. DVI 3. AV 4. HDMI Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV MagicBright MENU → → , → ENTER → [Picture] → ENTER → [MagicBright] → ENTER MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching.
Adjusting the LCD Display 1. Entertain High brightness For watching motion pictures such as a DVD or VCD. 2. Internet Medium brightness For working with a mixture of images such as texts and graphics. 3. Text Normal brightness For documents or works involving heavy text. 4. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
Adjusting the LCD Display → , → ENTER Adjusts the Sharpness. Color Tone MENU → → , → ENTER → [Picture] → → →ENTER → [Color Tone] → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp function is disabled.
Adjusting the LCD Display → , → ENTER Green MENU → → ENTER → [Picture] → → [Green] → , → → → ENTER → [Color Control] → → ENTER → ENTER Blue MENU → → ENTER → [Picture] → ENTER → [Blue] → , → → → ENTER → [Color Control] → → → → ENTER Color Temp MENU → → , → ENTER → [Picture] → → → → ENTER → [Color Temp] → ENTER Color Temp is a measure of the 'warmth' of the image colors. (Not available in Dynamic Contrast mode of On.) Note This function is only enabled if the Color Tone is set to Off.
Adjusting the LCD Display Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → → ENTER → [Fine] → , → ENTER Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
Adjusting the LCD Display (Available in PC mode only) Signal Balance MENU → → ENTER → [Picture] → → ENTER → [Signal Balance] → , → → → → → → ENTER → [Signal Balance] → → → → → ENTER → [Signal Balance] → ENTER Selects either On or Off with the signal control. Signal Control MENU → → ENTER → [Picture] → → → ENTER → [Signal Control] 1. → R-Gain MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → → ENTER → [Signal Control] → ENTER → [R-Gain] → ENTER → , 2.
Adjusting the LCD Display → , 5. → ENTER G-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → → ENTER → [Signal Control] → → → → → ENTER→ [G-Offset] → ENTER → , 6. → ENTER B-Offset MENU → → ENTER → [Picture] → → → ance] → → ENTER → [Signal Control] → → → ENTER → , → → → → ENTER → [Signal Bal→ → → → → ENTER[B-Offset] → ENTER Size MENU → → , → ENTER → [Picture] → → → → → → → → ENTER → [Size] → → → → → → → → ENTER → [Dynamic → ENTER The Size can be switched. 1.
Adjusting the LCD Display Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Picture [ AV / HDMI / TV Mode] Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Mode MENU → → , → ENTER → [Picture] → ENTER → [Mode] → ENTER The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated.
Adjusting the LCD Display (Not available in Dynamic Contrast mode of On.) Contrast MENU → → , → ENTER → [Picture] → → ENTER → [Custom] → ENTER→ [Contrast] → ENTER Adjusts the Contrast. Brightness MENU → → , → ENTER → [Picture] → → ENTER → [Custom] → → ENTER→ [Brightness] → ENTER Adjusts the Brightness. Sharpness MENU → ness] → , → ENTER → [Picture] → → ENTER → [Custom] → → → ENTER→ [Sharp- → ENTER Adjusts the picture Sharpness.
Adjusting the LCD Display Color Tone MENU → → , → ENTER → [Picture] → → → ENTER → [Color Tone] → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp function is disabled.
Adjusting the LCD Display → , → ENTER The Size can be switched. 1. 16:9 2. Zoom 1 3. Zoom 2 4. 4:3 5. Just Scan (Not available in Dynamic Contrast mode of On.) Note The Zoom1, Zoom2 are not available HDMI. The Just Scan are available in HDMI. Digital NR (Digital Noise Reduction) MENU → → , → ENTER → [Picture] → → → → → → ENTER → [Digital NR] → ENTER Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1.
Adjusting the LCD Display → , → ENTER Turns Film Mode Off/On. The Film Mode feature offers you a theater-quality viewing experience. (Not available in HDMI Mode) 1. Off 2. On Dynamic Contrast MENU → Contrast ] → , → ENTER → [Picture] → → → → → → → → ENTER → [Dynamic → ENTER Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2.
Adjusting the LCD Display 1. Off 2. On Sound Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Mode MENU → → , → → ENTER → [Sound] → ENTER → [Mode] → ENTER The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialogue (i.e., news). 5.
Adjusting the LCD Display Note • You can hear the sound even when sound value is set to 0. • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass MENU → → , → → ENTER → [Sound] → → ENTER → [Custom ]→ENTER→ [Bass] → ENTER Emphasizes low frequency audio. Treble MENU → → , → → ENTER → [Sound] → → ENTER → [Custom ]→ →ENTER→ [Treble] → ENTER Emphasizes high frequency audio.
Adjusting the LCD Display SRS TS XT MENU → → , → → ENTER → [Sound] → → → → ENTER → [SRS TS XT] → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1. Off 2.
Adjusting the LCD Display Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer. MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER → [Setup] → → ENTER → [Time ] → ENTER→ [Clock Set] Clock Set MENU → → , → , → ENTER Current Time Setting.
Adjusting the LCD Display 6. 150 7. 180 On Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→ [On Timer] → , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU → → → → ENTER → [Setup] → → [Off Timer] → , / , → ENTER → [Time ] → → → → ENTER → ENTER Turns the LCD Display off automatically at a preset time.
Adjusting the LCD Display 1. High 2. Medium 3. Low 4. Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0∼ 9] → [0∼ 9] → [0∼ 9] The password can be changed. Energy Saving MENU → → , → → → ENTER → [Setup] → → → → → ENTER → [Energy Saving] → ENTER This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2. On Note If you want to reduce the standby power consumption, set Energy Saving to On.
Adjusting the LCD Display → , → ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI black level. 1. Normal 2.
Adjusting the LCD Display Format MENU → → → → ENTER → [Setup] → → → → Wall ]→ → ENTER → [Format] → , → → → ENTER → [Video → → → ENTER → [Video → → → ENTER → [Video → ENTER The Format can be selected to see a divided screen. 1. Full Provides a full screen without any margins. 2. Natural Displays a natural image with the original aspect ratio intact.
Adjusting the LCD Display → , → ENTER Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5. Screen Divider MENU → → → → ENTER → [Setup] → → → → Wall ]→ → → → → ENTER → [Screen Divider] → → → ENTER → [Video The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Divider. • Select a display in Display Selection.
Adjusting the LCD Display 1. Off 2. On Horizontal Dot MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → ENTER → [Horizontal Dot] → , → ENTER Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Line MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → → ENTER → [Vertical Line] → , → ENTER Sets how many pixels the screen moves vertically.
Adjusting the LCD Display Timer Timer MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → ENTER → [Timer] → , → ENTER You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. 1. Off 2.
Adjusting the LCD Display Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER Within the set period of time specify a time for execution.
Adjusting the LCD Display Eraser MENU → → → → ENTER → [Setup] → → → → Screen] → → → → →ENTER → [Eraser] → → → → ENTER → [Safety This function prevents after-images on the screen by moving a rectangular pattern.
Adjusting the LCD Display → , → ENTER Adjusts the Power On time for the screen. Caution: Set the Power On time to be loger to avoid overvoltage. Side Gray MENU → → → → ENTER → [Setup] → → → → → → → → → → → ENTER → [Side Gray] → , → ENTER Select the brightness of the grey for the screen background. 1. Off 2. Light 3. Dark Reset Reverts the product settings to factory defaults. The Reset function is only available when PC / DVI is being used.
Adjusting the LCD Display Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → [Setup] → → → → ENTER → [Reset ]→ → ENTER → [Color Reset ] → , → → → → → → → → → ENTER Lamp Control MENU → → → → ENTER → [Setup] → → → → → ENTER → [Lamp Control ] → , → → → → → → → → → ENTER Adjusts the inverter lamp in order to reduce energy consumption.
Adjusting the LCD Display → • , → [0~9] ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note • The operating system for this set only supports English so the other languages might be corrupted on the screen. • For MagicInfo, a remote control is available for MagicInfo.
Adjusting the LCD Display • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D:, EWF is not applied.
Adjusting the LCD Display Slide Show Displays the properties of the original file as they are. Interval Controls the time intervals between image files for a slide show.
Adjusting the LCD Display Rotation Displays an image file by turning it clockwise by 90 degrees. Zoom Displays a reduced picture.
Adjusting the LCD Display Close Closes the image control Menu. Music The MP3 file format is supported. Movie The MPEG1, WMV file format are supported.
Adjusting the LCD Display Play Plays a movie file. Full Size Plays a movie file in full screen.
Adjusting the LCD Display OFFICE / HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF, HTML, HTM files are displayed. Note • Install the proper viewer(freeware) program to see the MS Office(Word, Excel, Power Point) or PDF doucuments. Internet Connects to the Internet Setup Sets various functions in MagicInfo mode. A password must be entered to access Setup mode.
Adjusting the LCD Display Schedule View Displays a schedule. TCP/IP Changes the TCP/IP settings.
Adjusting the LCD Display Connection Modifies the network settings. Password The password can be changed. • The password should be between 6 and 12 characters in numeric format. (You should enter a password between 6 and 12 characters in numeric format) • If you enter the wrong password three times, the setup configuration is reset and a warning message appears from the server.
Adjusting the LCD Display • If you forget the password, enter Info, 8, 2 and 4 on the remote control to initialize the password. This will reset the previous settings of Setup mode. File Local : You can delete or copy files on both local and removable disks. Play Option You can set the repeat play and screen settings. Repeat : Determines the repeat option for playing movies and music. • None - Select No Repeat to play a movie or tune in the list only once.
Adjusting the LCD Display • File Repeat - Select Repeat File to play a movie or tune in the list repeatedly. • List Repeat - Select Repeat List to play movies or tunes in the list in sequence repeatedly. Rotation - Sets the picture orientation. • Landscape - Sets the screen resolution to 1366x768 pixels. • Portrait - Sets the screen resolution to 768x1366 pixels. EWF(Enhanced Write Filter) : Prevents change to and loss of the data saved on the disk.
Adjusting the LCD Display : Sets the picture to 16:9 wide mode. 3. Wide Zoom : Magnify the size of the picture more than 4:3. 4. Zoom : Magnifies the size of the picture on the screen. 5. 4:3 : Sets the picture to 4:3 normal mode. 6. Just Scan : Use the function to see the full image without any cutoff when HDMI (720p/1080i/1080p), DTV (1080i) signals are input. Note Auto Wide function is available only in TV, DTV, AV mode. In PC Mode, only 16:9 and 4:3 mode can be adjusted. Screen Mode D.
Adjusting the LCD Display → , → ENTER Select the country in which the product is being used before you use the Auto Store feature. If you do not see your country in the list, select Others. Auto Store D.MENU → →[Channel] → ENTER → → ENTER →[Auto Store] You can scan the frequency ranges available on your television in your area and store all the channels found automatically. Manual Store D.
Adjusting the LCD Display Colour System D.MENU → →[Channel] → ENTER → → → ENTER →[Manual Store] → [Colour System] → , →ENTER→ → ENTER Adjusts repeatedly until the colour is of the best quality. (Auto <-> PAL <-> SECAM <-> NTSC4.43 ) Sound System D.MENU → →[Channel] → ENTER → → → ENTER →[Manual Store] → → [Sound System] → , → →ENTER → ENTER Adjusts repeatedly until the sound is of the best quality. Channel D.
Adjusting the LCD Display - S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode. Search D.MENU → →[Channel] → ENTER → → → ENTER →[Manual Store] → → ENTER→ [Search] → , → → → → ENTER The tuner scans the frequency range until the first channel or the channel that you selected is received on your screen. Store D.
Adjusting the LCD Display You can add or delete a channel so only channels you want are displayed. is active when Child Lock is selected to On. Child Lock D.MENU → →[Channel] → ENTER → → → → ENTER →[Channel Manager] → →ENTER → [Child Lock] → , → ENTER Protects children from viewing inappropriate programs by blocking certain broadcast or video programs. The Child Lock feature can be selected only from the remote. Sort D.
Adjusting the LCD Display Fine Tune D.MENU → →[Channel] → ENTER → → → → → → → ENTER →[Fine Tune] → , / , → ENTER Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. LNA D.MENU → →[Channel] → ENTER → → → → → → → → ENTER →[LNA] → , → ENTER Turns the low noise amplifier on or off. Setup Plug & Play D.MENU → → →[Setup] → ENTER →ENTER →[Plug & Play] You can manage the entire configuration. Language D.
Adjusting the LCD Display The language chosen affects only the language of the OSD. Digital Menu Guide Now & Next Guide D.MENU → → → →[Digital Menu] → ENTER→[Guide] → ENTER→ENTER →[Now & Next Guide] For the six channels indicated in the left-hand column, displays the Current programme and the Next programme information. Full Guide D.MENU → → → →[Digital Menu] → ENTER→[Guide] → ENTER→ →ENTER →[Full Guide] Displays the programme information as time ordered One hour segments.
Adjusting the LCD Display Scheduled List D.MENU → → → →[Digital Menu] → ENTER→[Guide] → ENTER→ → →ENTER → [Scheduled List] If you make a scheduled viewing list of programs you may like to see, the channel will be automatically switched to the scheduled Programme at the scheduled time even if you are watching another program. You can also set hour and minute by pressing the number buttons on the remote control. 1. Channel : Set the channel. 2. Time : Set the time. 3. Date : Set Year, Month and Day.
Adjusting the LCD Display 5. Delete Delete the selected schedule. Default Guide D.MENU → → → →[Digital Menu] → ENTER→[Guide] → ENTER→ → → →ENTER → [Default Guide] → , → ENTER You can preset the default guide style. 1. Now/Next 2. Full Guide Digital Channel Country D.MENU → → → →[Digital Menu] → ENTER→ →[Digital Channel]→ENTER →[Country] → ENTER → , → ENTER Select the country in which the product is being used before you use the Auto Store feature.
Adjusting the LCD Display Note • Even though you have changed the country setting in this menu, the country setting for Analog TV is not changed . • When it has finished, the number of scanned services will be displayed. • The existing favourite channel list will not be deleted when the channel list is updated. • To stop the scan before it has finished, press the ENTER button with "Stop" selected.
Adjusting the LCD Display Note • A " " icon is shown next to the selected channel and the channel will be added to the favourite channel list. • To undo, press the ENTER button again. • Select All: Select all channels currently displayed. • Select None: Deselect all selected channels. • Preview: Displays (a) currently selected channel(s). The Favorite Channels settings have been completed. Add • D.
Adjusting the LCD Display Preview • D.MENU → → → →[Digital Menu] → ENTER→ →[Digital Channel]→ENTER → → →[Edit Favourite Channels] → ENTER → Press the yellow button The selected channel is displayed on the screen. Delete • D.MENU → → → →[Digital Menu] → ENTER→ →[Digital Channel]→ENTER → → →[Edit Favourite Channels] → ENTER → Press the blue button Note • The selected channel and number will be deleted. To add a deleted channel back in to the favourite channel list. Channel List D.
Adjusting the LCD Display • The channel number, name and an icon are displayed in the top left corner while changing the channel. • The channel number and name are displayed if the channel is one of the all channels, and a icon if the channel is one of the favourite channels. Setup Menu Transparency D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → [Menu Transparency] → ENTER → , → ENTER You can set the translucency of the menu. 1. High 2. Medium 3. Low 4. Opaque Change PIN D.
Adjusting the LCD Display → , → ENTER This feature allows you to prevent unauthorized users, such as children, from watching unsuitable programmes by a 4-digit PIN (Personal Identification Number) code that is defined by the user. The on-screen menu will instruct you to assign a PIN code (you can change it later, if necessary). Note • The default PIN code for a new TV set is 0000. • If you enter an invalid PIN code, the "Invalid PIN code. Please try again." message is displayed. Subtitle D.
Adjusting the LCD Display 2. Hard of hearing Note • If the programme you are watching does not support the "Hard of hearing" function, "Normal" automatically activates even though "Hard of hearing" mode is selected. Audio Format D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → → → → [Audio Format] → ENTER → → → , → ENTER You can only hear Dolby Digital sound through the audio receiver connected through an optical cable. You can only hear PCM sound through the main speaker.
Adjusting the LCD Display 1. Audio Description - Off, On 2. Volume Note • "Volume" is active when "Audio Description" is set to "On". Digital Text D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → → → → → → [Digital Text] → ENTER → → → , → ENTER If the programme is broadcast with digital text, this feature is enabled. 1. Disable 2.
Adjusting the LCD Display Note • The following options are available The Iberian Peninsula and Balears Islands - Canarian Islands Common Interface D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → → → → → → → → [Common Interface] 1. Application Info 2. CI Menu → → → → System D.
Adjusting the LCD Display D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → → → → → → → → → → [System] → ENTER → → →ENTER 4. • Software Information • Manual Upgrade • Standby Mode upgrade → Reset D.MENU → → → →[Digital Menu] → ENTER→ → →[Setup]→ENTER → → → → → → → → → → → [System] → ENTER → → → →ENTER →[0] ∼ [9] You can reset the values stored to the factory default values.
Adjusting the LCD Display You can change the default value for subtitle, audio teletext languages. Displays the language information for the incoming stream. Note • English is the default in cases where the selected language is unavailable in the broadcast. Subtitle Language D.MENU → → → →[Digital Menu] → ENTER→ → → →[Language]→ENTER → → ENTER →[Subtitle Language] → ENTER You can change the default value for subtitle, audio teletext languages. Displays the language information for the incoming stream.
Adjusting the LCD Display This menu consists of 6 sub-menus:Primary Subtitle Language, Secondary Subtitle Language, Primary Audio Language, Secondary Audio Language, Primary Teletext Language. 1. Primary Audio Language 2. Secondary Audio Language 3. Primary Subtitle Language 4. Secondary Subtitle Language 5.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused.
Troubleshooting PC Mode Q: The LCD Display screen flickers. A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) TV Mode Q: TV screen is blurred or shows noise signals. A: Check if the TV antenna connector is securely connected to the external antenna.(Refer to Connecting TV) Q: TV signal is not received A: Select "Auto Program" to configure the channel system automatically.
Troubleshooting A: Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display. If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. Q: Ghost images are shown in the picture. A: Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display.
Troubleshooting A: If the volume is still too low after turning the control to its maximum, check the volume control on the computer sound card or software program. Q: The sound is too high or too low. A: Adjusts the Treble and Bass to the appropriate levels. Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: The remote control buttons do not respond. A: Check the polarities (+/-) of the batteries.
Troubleshooting Set the resolution in the Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Set the resolution in the Control Panel → Display → Settings. * Contact the video card manufacturer for details. Q: How can I set the Power Saving function? A: Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual).
Troubleshooting A: An SDTV has an aspect ratio of 4:3 which is the same as that of an analog TV. HDTV has an aspect ratio of 16:9 which is similar to a cinema screen. This provides a much better screen quality than SDTV. It's like having a theater in your home. A: Digital TV broadcasting in our country is ultimately orientated towards HDTV. Q: Can I watch HD broadcasting with all digital TVs? A: You can receive all digital broadcasts, whether they are SD or HD, using any digital TV.
Specifications General General Model Name SyncMaster 400CXN LCD Panel Size 40 " Diagonal (101 cm) Display area 885.17 mm (H) X 497.7 mm (V) Pixel Pitch 0.648 mm (H) X 0.648 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M Resolution Optimum resolution 1360 x 768 @ 60 Hz / 1366 x 768 @ 60 Hz depends on graphics card used Maximum resolution 1920 x 1080 @ 60 Hz (RB) Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.
Specifications VESA Mounting Interface 600 x 400 mm Environmental considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings.
Specifications Item Specification Remarks Office (Word, Excel, Power Point) or PDF documents. Internet Browser MS Internet Explorer Not Support Flash, Java Applet, Security Site Language English OS Windows XP Embedded MagicInfo Pro - Server Requirement CPU RAM Ethernet OS Application Minimum P1.8 GHz 256 M 100 M / 1 Windows WMP 9 or latG XP er Recommended P3.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 848 x 480 31.020 60.000 33.750 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.
Specifications Display Color 16.7 M Resolution Optimum resolution 1920 x 1080 @ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p ±5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Dot Acceptable TFT-LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above are used for this product. But the pixels of RED, GREEN, BLUE and WHITE color appear to be bright sometimes or some black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800.
Specifications PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when leaving it unattended for long periods.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 1360 x 768 47.712 60.015 85.500 +/+ VESA, 1600 x 1200 75.000 60.000 162.000 +/+ VESA, 1920 x 1080 66.587 59.934 138.500 +/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1360(1920) x 768(1080) • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the LCD Display to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement.
Information Note ( Please check CD's User Guide at "OSD Function", some model's will not available ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down.
Information - Select method • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 second ( Recommend : 50 ) Note ( Please check CD's User Guide at "OSD Function", some model's will not available )
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.
Appendix Europe GERMANY 01805 - SAMSUNG (726-7864) http://www.samsung.com (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LUXEMBURG 0035 (0)2 261 03 710 http://www.samsung.com/be NETHERLANDS 0900 SAMSUNG (726-7864 € http://www.samsung.com/nl 0,10/Min) NORWAY 815-56 480 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.com/pl 022-607-93-33 PORTUGAL 80820-SAMSUNG (726-7864) http://www.samsung.
Appendix Asia Pacific TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG(726-7864) http://www.samsung.com 8000-4726 Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution.
Appendix ble network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network. CATV "CATV" refers to the broadcasting service offered at hotels, schools and other buildings through their own broadcasting system, apart from VHF or UHF broadcasting by terrestrial broadcasters. The CATV programs may include movies, entertainment and educational programs. (Different from cable TV.) CATV can be viewed only within the area in which the CATV service is offered.
Appendix In HD, 1080-line, 2x density beaming (1080i) is used. HD provides a five times clearer screen quality than the existing analog method and has a wide 16:9 aspect ratio. • SD (Standard Definition) In SD, 480-line, double beaming (480i) is used. SD provides a screen quality somewhere between HD and the existing analog method. It exhibits a two times better screen quality than analog TV. SRS TS XT This feature outputs sonorous and vivid 3D sound as for 5.
Appendix
