SyncMaster 400UXN-UD2,460UXN-UD2 LCD Display User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor.
Safety Instructions When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it with a slightly moistened, soft cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Safety Instructions Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
Safety Instructions • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater. • This may reduce the lifetime of the product, and may result in fire. Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result in electric shock or fire.
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. both sides of the package box. Remove the Styrofoam and vinyl cover.
Introduction Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) Magic Wall Software CD, Magic Wall Manual CD Cables Power Cord Others Remote Control Batteries (AAA X 2) (BP59-00138A) (Not available in all locations) Sold separately D-Sub Cable DVI Cable Wall Mount KIT RGB to BNC Cable 9 LAN Cable D-sub to Component Cable
Introduction Sold separately Semi Stand KIT Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values.
Introduction • PC : DVI / AV / HDMI • DVI / AV : PC • HDMI : PC Power button [ ] Use this button for turning the LCD Display on and off. Brightness Sensor (Optional) Automatically detects the surrounding brightness. Note This function is activated only on the models equipped with an auto brightness sensor. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions.
Introduction POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB / COMPONENT IN (PC Connection Terminal (Input)) • Use a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) • Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the DSUB to COMPONENT cable.
Introduction • Connect the [DVI OUT] port on the monitor to the HDMI IN port on the other monitor using the DVI to HDMI cable. • DVI, HDMI and network signals sent via the [DVI OUT] port are displayed on the second display which has the DVI IN port. Note Up to 6 Full HD or 10 HD monitors can be connected (May differ depending on the product). AV IN [VIDEO] Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.
Introduction Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on the model.
Introduction POWER OFF Number Buttons DEL / GUIDE button + VOL SOURCE D.MENU TOOLS Up-Down Left-Right buttons INFO COLOR BUTTONS TTX/MIX MTS/DUAL ENTER/PRE-CH MUTE CH/P TV MENU RETURN EXIT MagicInfo 1. POWER Turns the product On. 2. OFF Turns the product Off. 3. Number Buttons 4. DEL ton / GUIDE but- Press to change the channel. The "-" button is used to select Digital channels. Electronic Program Guide (EPG) display. - This function does not work for this LCD Display. 5. + VOL 6.
Introduction - This function does not work for this LCD Display. 9. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. INFO Current picture information is displayed on the upper left corner of the screen. 11. COLOR BUTTONS Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu. 10. - This function does not work for this LCD Display. 12.
Introduction 19. RETURN Returns to the previous menu. 20. EXIT Exits from the menu screen. 21. MagicInfo MagicInfo Quick Launch Button.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB / COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer.
Connections Using the HDMI (digital) output on the graphics card. • Connect the [HDMI IN] port on the monitor to the HDMI port on the PC using the HDMI cable. Note When the HDMI cable to the PC, ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted. Note that sound is only available when connected according to the option that follows.
Connections Connecting AV Devices 1. Connect the Video and Audio R-AUDIO-L port of the DVD, VCR or DTV Set-Top Box to the Video and Audio [R-AUDIO-L] LCD Display. 2. Play the DVD, VCR or Camcorder with a DVD disc or tape inserted. 3. Select AV using the SOURCE button on the front of the LCD display or on the remote. Connecting using a Component Cable 1.
Connections For an explanation of Component video, consult your DVD or external device's user manual. Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV/COMPONENT AUDIO IN [L-AUDIO-R]] on the LCD Display . 2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN [VIDEO]] on the LCD Display . 3.
Connections 1. Connect between the [DVI OUT] port on the LCD monitor and the input port on another monitor using a DVI cable. 2. Connect between the [AUDIO OUT] port on the LCD monitor and the audio input port on another monitor using a stereo cable. 3. Select DVI using the SOURCE button on the front of the LCD Display or on the remote control. Note DVI OUT does not support HDCP. Connecting Using a HDMI Cable 1.
Connections Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the [HDMI IN] terminal of the LCD Display using a DVI to HDMI cable. 2. Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the [DVI / RGB /HDMI AUDIO IN] terminal of the LCD Display. 3.
Connections Note Select Component using the SOURCE button on the front of the LCD Display or on the remote control. For an explanation of Component video, see your Set Top Box owner's manual. Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connecting a LAN Cable The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. Connect the LAN cable.
Connections 25
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. (Start) and "Control Panel". Then, double-click on "Appearance and PersonalClick ization". 3. Click "Personalization" and then "Display Settings". 4.
Using the Software If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft,, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver), then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. MDC (Multi-Display Channel) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MDC executable file on the CD. 3. When the Installation Shield Wizard window appears, click "Next". 4.
Using the Software Using MDC 35
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can change. The original value is COM1. 5.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. Power Control 1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display.
• PC Mode
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
The Input Source Control feature is available only for the displays whose power status is ON. Image Size PC, BNC, DVI 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Info Grid displays only the displays whose Input Source is PC, BNC, DVI.
Image Size TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source.
1. Click Time of the main icons and the Time Control screen appears. Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display.
PIP Size 1. Click PIP of the main icons and the PIP control screen appears. Click Select All or use Check Box to select a display to control. Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small.
PIP PIP Source 1. Click PIP of the main icons and the PIP control screen appears. Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI.
Settings Picture 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide.When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM.
- Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display. The Input source of MagicInfo works only on MagicInfo model. Color Temp is only enabled if the Color Tone is set to Off. The Input source of TV works only on TV model.
2) Contrast - Adjusts Contrast of the selected display. 3) Brightness - Adjusts Brightness for the selected display. 4) Red - Adjusts red Color of the selected display. - Available only for NT. 5) Green - Adjusts green Color of the selected display. - Available only for NT. 6) Blue - Adjusts blue Color of the selected display. - Available only for NT. 7) Color Tone - Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed. Changing a value in this screen will automatically change the mode to "CUSTOM." 1) Audio - Controls audio settings for all input sources. 2) Bass - Adjusts Bass of the selected display.
Image Lock 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicInfo works only on MagicInfo model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen. 1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection.
You may not operate this function in MagicInfo. The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON. Troubleshooting 1. The display you wish to control does not appear on the Power Control Info Grid - Check the connection of RS232C. (Check if it is properly connected to the Com1 port) - Check the displays to see if any of the other displays connected have the same ID.
2. Selected one display: Fetches and displays the settings value for the selected display. 3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of ID 1, fetches and displays the value of ID3. 4. Selected all sets using Select All: Returns to the Factory Default Value.
Adjusting the LCD Display Input Available Modes • PC / DVI • AV • Component • HDMI • MagicInfo Source List MENU → ENTER → → , → ENTER → → ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5. HDMI 6.
Adjusting the LCD Display Note • If you select , , in Size, Position and Transparency will not be activated. PIP MENU → ENTER → → , → → ENTER → → ENTER → → →ENTER → → → ENTER Turns the PIP Screen Off/On. • Off • On Source MENU → ENTER → → , →ENTER → → ENTER Selects the input source for the PIP.
Adjusting the LCD Display Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. Size MENU → ENTER → → , → →ENTER → → → → → ENTER → → ENTER Changes the Size of the PIP window. Position MENU → ENTER → → , → →ENTER → → → → → → ENTER → → ENTER Changes the Position of the PIP window. Transparency MENU → ENTER → → , → → ENTER → → ENTER Adjusts the Transparency of PIP windows.
Adjusting the LCD Display • Medium • Low • Opaque Note • PIP turns off when the LCD Display is switched to an external source. • For PC and DVI, this is deactivated if the cable is disconnected. Edit Name MENU → ENTER → , → → ENTER → → → → ENTER Name the input device connected to the input jacks to make your input source selection easier.
Adjusting the LCD Display → , → ENTER MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet, Text and Custom. Each mode has its own pre-configured brightness value. (Not available when Dynamic Contrast is set to On.) 1. Entertain High brightness For watching motion pictures such as from a DVD or VCR. 2.
Adjusting the LCD Display → , → ENTER Adjusts the Contrast. Brightness MENU → → , → ENTER → → ENTER → → → → ENTER → → ENTER Adjusts the Brightness. Sharpness → ENTER → MENU → → , → ENTER → → → → → ENTER → → ENTER Adjusts the Sharpness. Color Tone MENU → → , → ENTER → → → →ENTER → → ENTER The color tones can be changed. (Not available when Dynamic Contrast is set to On.) 1. Off 2. Cool 3. Normal 4. Warm 5.
Adjusting the LCD Display If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance. MENU → → ENTER → → → → → ENTER → (Not available when Dynamic Contrast is set to On.) Note If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.
Adjusting the LCD Display Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. (Available in PC mode only) MENU → → ENTER → → → → → → ENTER → → Coarse MENU → → ENTER → ENTER → → , → → → → → → ENTER → → → ENTER Removes noise such as vertical stripes.
Adjusting the LCD Display The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. (Available in PC mode only) Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable.
Adjusting the LCD Display → , 3. → ENTER B-Gain MENU → → , 4. → → → → → → → ENTER → → → → ENTER→ → → → → → → → → → R-Offset → , → ENTER → → ENTER → → → → → → → → → → ENTER → → ENTER→ → ENTER G-Offset MENU → → , 6. → → ENTER MENU → 5.
Adjusting the LCD Display 1. 16:9 2. 4:3 HDMI Black Level MENU → → , → ENTER → → → → → → → → ENTER → → ENTER When watching with a DVD or set-top box connecting to the product via HDMI or DVI, image quality deterioration (black level, lower-quality contrast, lighter color tone, etc.) may occur depending on the connected external device. 1. Normal 2. Low Note • For Timing which can be used for both the PC and the DTV in DVI, HDMI mode, HDMI Black Level will be activated.
Adjusting the LCD Display → , → ENTER Adjusts the Brightness of the PIP window on the screen. 3. Sharpness MENU → → → , → ENTER → → → → → ENTER → → → → → → → → → → ENTER → ENTER Adjusts the Sharpness of the PIP window on the screen. 4. Color MENU → → → , → ENTER → → → → → → → ENTER → → → → → → → → → ENTER → ENTER Adjusts the Color of the PIP window on the screen. Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. 5.
Adjusting the LCD Display → , → ENTER Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Lamp Control MENU → → → , → ENTER → → → → → → → → → → → → → ENTER → ENTER Adjusts the inverter lamp in order to reduce energy consumption. Note This function does not operate when Dynamic Contrast is set to On in PC, DVI, AV, HDMI, Component or MagicInfo modes.
Adjusting the LCD Display 1. Dynamic 2. Standard 3. Movie 4. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. MENU → → ENTER → → ENTER → → (Not available when Dynamic Contrast is set to On.) Contrast MENU → → , → ENTER → → ENTER → → → ENTER→ → ENTER Adjusts the Contrast. Brightness MENU → → , → ENTER → → → ENTER → → → ENTER → → ENTER Adjusts the Brightness.
Adjusting the LCD Display Tint MENU → → → , → ENTER → → → ENTER → → → → → → → → ENTER → ENTER Adds a natural tone to the display. Color Tone MENU → , → → ENTER → → ENTER → → ENTER The color tones can be changed. The individual Color components are also user adjustable. (Not available when Dynamic Contrast is set to On.) 1. Off 2. Cool2 3. Cool1 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp.
Adjusting the LCD Display Note This function is only enabled if the Color Tone is set to Off. Size MENU → → , → ENTER → → → → → → ENTER → → ENTER The Size can be switched. 1. 16:9: Sets the picture to 16:9 wide mode. 2. Zoom 1: Magnifies the size of the picture on the screen. 3. Zoom 2: Magnifies the size of the picture more than Zoom 1. 4. 4:3: Sets the picture to 4:3 normal mode. 5.
Adjusting the LCD Display 1. Off 2. On Note Digital NR function is not available for all resolutions. HDMI Black Level MENU → → , → ENTER → → → → → → → → ENTER → → ENTER When a DVD or set-top box is connected to your TV via HDMI or DVI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Adjusting the LCD Display 1. Off 2. On PIP Picture MENU → → , → ENTER → → → → → → → → → → ENTER → → ENTER Adjusts the PIP Screen Settings. Note • 1. Available Modes: PIP ON Contrast MENU → → , → ENTER → → ENTER→ → → → → → → → → → ENTER → → → → → → ENTER → → → → → ENTER → → → → → ENTER → → ENTER Adjusts the Contrast of the PIP window on the screen. 2.
Adjusting the LCD Display Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. 5. Tint MENU → → , → ENTER → → → → → → → → ENTER→ → → → → → → → ENTER → → ENTER Adds a natural tone to the PIP window. Note Enabled only when the PIP input is selected in AV, HDMI or Component mode. Operates only if the video signal is NTSC.
Adjusting the LCD Display Sound Available Modes • PC / DVI • AV • Component • HDMI • MagicInfo Mode MENU → → , → → ENTER → → ENTER → → ENTER The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialog (i.e., news). 5.
Adjusting the LCD Display • If you adjust sound using Custom function, Mode will turn to Custom mode. Bass MENU → → , → → ENTER → → → ENTER → →ENTER→ → ENTER Emphasizes low frequency audio. Treble MENU → → , → → ENTER → → → ENTER → → → ENTER → → ENTER Emphasizes high frequency audio. Balance MENU → → , → → ENTER → → → ENTER → → → → ENTER Allows you to Adjusts the sound balance between the left and right speakers.
Adjusting the LCD Display → , → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround XT delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. 1. Off 2. On Sound Select MENU → → , → → ENTER → → → → → → ENTER → → → → → ENTER Selects either Main or Sub when PIP is On.
Adjusting the LCD Display When you use the product with it connecting to a Home theater, turn the Internal speakers off so you can listen to sound from the Home theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker. 2. External When sound is only outputted from the External speakers, the volume control is also only available from the External speakers.
Adjusting the LCD Display Clock Set MENU → → , → → , → → ENTER → → → ENTER → → ENTER→ → ENTER Current Time Setting. Sleep Timer MENU → → , → → → ENTER → → → ENTER → → → ENTER→ → ENTER Turns the LCD Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7.
Adjusting the LCD Display → , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically. Off Timer MENU → → → , → → → ENTER → / , → → ENTER → → ENTER Turns the LCD Display off automatically at a preset time. Menu Transparency MENU → → , → → → ENTER → → → → ENTER → → ENTER Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4.
Adjusting the LCD Display Safety Lock Change PIN MENU → → → → ENTER → → → → → → ENTER → → ENTER → [0~9] → [0~9] → [0~9] → [0~9] The password can be changed. Note The preset password for the LCD Display is "0000". Lock On MENU → → → → ENTER → ENTER → → → → → ENTER → → → → [0~9] → [0~9] → [0~9] → [0~9] This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings.
Adjusting the LCD Display 2. On Video Wall A Video Wall is a set of video screens connected together, so that each screen shows a part of the whole picture or where the same picture is repeated on each screen. When the Video Wall is on, you can adjust the Video Wall screen setting. MENU → → → → ENTER → → → → → → → → ENTER → Note When Video Wall is running, the Auto Adjustment, Image Lock, and Size functions are not available. Video Wall does not operate in MagicInfo mode.
Adjusting the LCD Display Provides a full screen without any margins. 2. Natural Displays a natural image with the original aspect ratio intact. Horizontal MENU → → → → ENTER → → → → ENTER → → , → → → → → → → ENTER → → ENTER Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5. Vertical MENU → → → → ENTER → → → → → ENTER → → , → → → → → → → ENTER → → ENTER Sets how many parts the screen should be divided vertically.
Adjusting the LCD Display The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Divider. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time.
Adjusting the LCD Display Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical MENU → → → → ENTER → → ENTER → → → → ENTER → → , → ENTER → → → → → → → → → → ENTER → → → ENTER → → , → ENTER → → → → → → → → ENTER → Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time MENU → → → → ENTER → → ENTER → Set the time interval for performing the horizontal or vertical movement, respectively.
Adjusting the LCD Display 1. Off 2. On Mode MENU → → → → ENTER → → → ENTER → → → → → → → ENTER → → → → → → → → → → ENTER → → → → ENTER → → , → ENTER You can change the Safety Screen Type. 1. Scroll 2. Bar 3. Eraser Period MENU → → → → ENTER → → → ENTER → → → → ENTER → → , → ENTER Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → → → ENTER → → → → → → → → → → → ENTER → Within the set period of time specify a time for execution.
Adjusting the LCD Display • Mode-Bar, Eraser : 10~50 sec Scroll MENU → → → → ENTER → → → → ENTER → → → → → → → → → ENTER → This function helps to remove after-images on the screen by moving all the pixels on the LCD according to a pattern. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time.
Adjusting the LCD Display → , → ENTER Select the brightness of the grey for the screen background. 1. Off 2. Light 3.
Adjusting the LCD Display Power On Adjustment MENU → → , → → → → ENTER → → → → → → → → → → → ENTER → ENTER Adjusts the Power On time for the screen. OSD Rotation MENU → → → → ENTER → → → → → → → → → → → → → → → ENTER → , → → ENTER OSD Rotate 1. Landscape 2. Portrait Reset Reverts the product settings to factory defaults. The Reset function is only available when PC / DVI is being used.
Adjusting the LCD Display → , → ENTER Note Available in PC mode only Note The Reset function is not available when Video Wall is On. Color Reset MENU → → → → ENTER → → ENTER → → → ENTER → → , → → → → → → ENTER Multi Control Available Modes • PC / DVI • AV • Component • HDMI • MagicInfo Multi Control Assigns an individual ID to the SET.
Adjusting the LCD Display → • , → [0~9] ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes • PC / DVI • AV • Component • HDMI • MagicInfo Note • The remote control can be used to select MagicInfo. However, it is recommended to use a separate USB keyboard to utilize MagicInfo fully.
Adjusting the LCD Display • When using MagicInfo with the MagicInfo Server Program: perform Network mode. • When using MagicInfo with the device directly connected to LCD Display : execute Device mode. • Press ESC to directly go to the MagicInfo Window screen. • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Q: Shadowiness on the fringe of the panel due to technical limitations. A: The slight shadowiness on the fringe of the panel is due to the inside sheet that is seen through the thin outer bezel, which is not a defect but a technical limitation for the panel in the slim bezel design.
Troubleshooting Q: The image is too light or too dark. A: Adjusts the brightness and contrast. (Refer to the Brightness, Contrast) Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks.
Troubleshooting Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed. Q: The remote control buttons do not respond. A: Check the polarities (+/-) of the batteries. A: Check if the batteries are empty. A: Check if the power is on. A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity.
Troubleshooting A: Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display. Q: How can I play the video? A: The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to play the video. Note that some of the codecs can be incompatible.
Specifications General General Model Name SyncMaster 400UXN-UD2 SyncMaster 460UXN-UD2 LCD Panel Size SyncMaster 40 " Diagonal (101 cm) 400UXN-UD2 SyncMaster 46 " Diagonal (116 cm) 460UXN-UD2 Display area SyncMaster 885.6 mm (H) X 498.15 mm (V) 400UXN-UD2 SyncMaster 1018.08 mm (H) X 572.67 mm (V) 460UXN-UD2 Pixel Pitch SyncMaster 0.46125 mm (H) X 0.46125 mm (V) 400UXN-UD2 SyncMaster 0.53025 mm (H) x 0.
Specifications Maximum Pixel Clock 148.5 MHz (Analog,Digital) Power Supply This product supports 100-240 V. Since the standard voltage may differ from country to country, please check the label on the back of the product. Signal Cable D-sub, DVI-D, AV(Composite,CVBS), HDMI, RS232C In/Out,PC Audio(Stereo) In,Audio Out , DVI OUT, LAN, USB(3port), VGA OUT, Component Dimensions (W x H x D) / Weight SyncMaster 400UXN-UD2 914 x 118 x 526 mm / 36.0 x 4.6 x 20.7 inch (Without Stand) / 23.0 kg / 50.
Specifications Note Design and specifications are subject to change without prior notice. Note Class A Equipment PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Fre- Pixel Clock quency (Hz) (MHz) Sync Polarity (H/V) VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 768 47.776 59.870 79.500 -/+ VESA, 1280 x 960 60.000 60.000 108.000 +/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD. • Resolution: 1920 x 1080 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement.
Information • Time Period : 1 ~ 5 seconds ( Recommend : 5 ) Apply the Screen Pixel function on Product • Apply the Screen Pixel function - Symptom: Dot with Black Color move up and down. - Select method • • Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Pixel • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 seconds ( Recommend : 50 ) Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down.
Information • Time Interval : 1 ~ 10 hours ( Recommend : 1 ) • Time Period : 10 ~ 50 seconds ( Recommend : 50 ) 87
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx Latin America ARGENTINA 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe BELGIUM 02 201 2418 http://www.samsung.com/be (Dutch) http://www.samsung.com/ be_fr (French) CZECH REPUBLIC 800 (800-726786) SAMSUNG http://www.samsung.com/cz DENMARK 8 - SAMSUNG (7267864) http://www.samsung.com/dk EIRE 0818 717 100 http://www.samsung.com/ie FINLAND 30 - 6227 515 http://www.samsung.com/fi FRANCE 01 4863 0000 http://www.samsung.com/fr GERMANY 01805 SAMSUNG http://www.samsung.de (7267864, € 0.14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.
Appendix CIS http://www.samsung.com/ ua_ru UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com/ kz_ru Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 400-810-5858 http://www.samsung.com/cn 010-6475 1880 HONG KONG 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282 http://www.samsung.com/in 1-800-3000-8282 1800 110011 INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.
Appendix Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle.
Appendix Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.
