SyncMaster 913N/915N/912T/913T/913B/901B Install drivers Install programs
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Do not drop the monitor when moving it. z This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. z Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. z Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or back).
Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor.
Adjust the resolution and frequency to the levels appropriate for the model. z Inappropriate resolution may cause undesirable picture quality. 19 inch (48 cm) - 1280 X 1024 Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations.
SyncMaster 913N/915N Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Option 1 Monitor & Simple stand Bottom MagicRotation™ program can not be provided as Simple Stand does not support Pivot function.
Quick Setup Guide Warranty Card (Not available in all locations) D-Sub Cable Power Cord User's Guide, Monitor Driver, Natural Color software, MagicTune™ software, MagicRotation software Cable Front 1. Menu button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. 2. MagicBright button [ ] MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text : Normal brightness For documentations or works involving heavy text. 3) Internet : Medium brightness For working with a mixture of images such as text and graphics. 4) Entertain : High brightness For watching motion pictures such as a DVD or VCD. >>Click here to see an animation clip 3. Brightness button [ ] 2,3.
For using a locking device, contact where you purchase it. See Connecting the Monitor for further information regarding cable connections.
SyncMaster 912T/913T/913B/901B Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Option 1 Monitor & Simple stand Bottom MagicRotation™ program can not be provided as Simple Stand does not support Pivot function.
Quick Setup Guide Warranty Card (Not available in all locations) D-Sub Cable Power Cord User's Guide, Monitor Driver, Natural Color software, MagicTune™ software, MagicRotation software Cable Sold separately DVI Cable Front 1. Menu button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
2. 3. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of four settings by simply pressing MagicBright control button.
(The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. 3. DVI port D-sub 15-pin port 4. Kensington Lock Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI cable to the DVI port on the back of your Monitor. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your monitor. The Kensington lock is a device used to physically fix the system when using it in a public place.
SyncMaster 913N/915N 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 2-3.
Monitor and Bottom Pivot Stand A. Stand Stopper Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Simple stand A. Monitor Pivot stand B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CDROM Drive, click the [Start] button of Windows and then select [Execute].
SyncMaster 912T/913T/913B/901B 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the D-sub cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI port on the back of your monitor. 2-3. Connected to a Macintosh.
Monitor Assembly Monitor and Bottom Pivot Stand A. Stand Stopper Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Simple stand A. Monitor Pivot stand B. Mounting interface pad 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CDROM Drive, click the [Start] button of Windows and then select [Execute].
SyncMaster 913N/915N 1. [ ]Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]This button allows you to adjust items in the menu. 4. [ ]Press this button to activate a highlighted menu item. 5. [AUTO]Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. z z If auto adjustment does not work properly, press auto button again to adjust picture with more accuracy.
Brightness Menu Description When OSD is not on the screen, push the button to adjust brightness. Brightness 1. Picture Brightness Contrast 2. Color Color Tone Color Control Gamma 3. Image Coarse Fine Sharpness H-Position V-Position 4. OSD Language H-Position V-Position Transparency Display Time 5. Setup 6.
Menu Description Brightness You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, Push the button to adjust brightness. Contrast You can use the on-screen menus to change the contrast according to personal preference. Play/Stop Color Menu Color Tone Color Control Description The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom.
Select one of three pre-defined gammas. Gamma z z z Mode 1 : Shows normal gamma Mode 2 : Shows higher gamma(brighter) Mode 3 : Shows lower gamma(darker) Image Menu Description Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
Menu Description Change the language used in the menu. You can choose one of the seven languages. Language Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. H-Position You can change the horizontal position where the OSD menu appears on your monitor. V-Position You can change the vertical position where the OSD menu appears on your monitor. Transparency Change the transparency of the background of the OSD.
Menu Description Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values. Information Menu Information Description Shows a video source, display mode on the OSD screen.
SyncMaster 912T/913T/913B/901B 1. [ ]Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. 2. [ ]This button allows you to adjust items in the menu. 3. [ ]This button allows you to adjust items in the menu. 4. [ ]Press this button to activate a highlighted menu item. 5. [AUTO]Press to self-adjust to the incoming PC signal. The values of fine,coarse and position are adjusted automatically.
Menu Description When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
- four different modes(Custom/Text/Internet/Entertain) Brightness Menu Description When OSD is not on the screen, push the button to adjust brightness. Brightness SOURCE Menu SOURCE 1. Picture Description Selects the video signal while the OSD is off.
2. Color Color Tone Color Control Gamma 3. Image Coarse Fine Sharpness H-Position V-Position 4. OSD Language H-Position V-Position Transparency Display Time 5. Setup 6. Information Auto Source Image Reset Color Reset Picture Menu Description Brightness You can use the on-screen menus to change the brightness according to personal preference. Direct Access Feature : When OSD is not on the screen, Push the button to adjust brightness.
Menu Color Tone Color Control Description Play/Stop The tone of the color can be changed and one of four modes can be selected - Cool, Normal, Warm and Custom. Adjusts individual R,G,B color balance. Select one of three pre-defined gammas. Gamma z z z Mode 1 : Shows normal gamma Mode 2 : Shows higher gamma(brighter) Mode 3 : Shows lower gamma(darker) Image Menu Description Removes noise such as vertical stripes.
Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. (Available in analog mode only) Fine Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). (Available in analog mode only) Sharpness Changes the clearance of image. H-Position Changes the horizontal position of the monitor's entire display.
You can set the amount of time the menu will wait before it is turned off. Setup Menu Description Auto Source Select Auto Source for the monitor to automatically select the signal source. Image Reset Image parameters are replaced with the factory default values. Color Reset Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune™ program. 7. Click "Install." 8. The "Installation Status" window appears.
9. 10. Click "Finish." When the installation is complete, the MagicTune™ executable icon appears on your desktop. Double-click the icon to start the program. MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
OS z z z z z Windows™ Windows™ Windows™ Windows™ Windows™ 98 SE Me 2000 XP Home Edition XP Professional It is recommended using MagicTune™ in Windows™ 2000 or later. Hardware z z 32MB Memory above 25MB Hard disk space above * For more information, visit the MagicTune™ website.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of MagicTune™ Program may not operate normally.
Picture Tab Definition Allows the user to adjust the screen settings to the desired values. j Resolution n k l m i Brightness n j k l m n j Contrast n k l m j MagicBright k l m Brightness Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions. Contrast Adjusts the difference in brightness between the bright and dark areas on screen.
n Color Tone m i j k l m n Color Control m j k l n Calibration j k l The tone of the color can be changed. Color Tone z z Color Control Adjusts of the monitor image color. You can change the monitor color to your desired color. z Calibration Warm - Normal - Cool Custom R- G - B The process through which the colors of your choice are optimized and maintained.
i Image Setup n j k l m n j Position k l m z Image Setup z z Position Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal.
z Preferences z Source Select Enable task tray menu . - To access the MagicTune™ menus, click the icon on the [task tray menu]. The menus are not displayed if the [Enable System Tray] is deselected in [Options] ' [Basic Settings]. Select Language - The language chosen affects only the language of the OSD. Source Select will be shown only in dual monitor. In analog only model source select will not be shown.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. 2. 3. 4. 5.
Press "Preview" button on the Color Calibration. The above picture will be shown. 1. 2. Press "View Calibrated" button to see the calibration effect which you adjusted. Press "View Uncalibrated" button to see the original image.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows™ Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Troubleshooting The current computing system is not compatible with MagicTune™. Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home page for further reference. An error may occur when your video/graphic card is not in the 'Available' list. (The latest or oldest video cards may not be compatible.) Please visit our homepage to see the Troubleshooting section.
Visit the video card maker's homepage and download and install the latest driver. For more information about the video card, contact the card manufacturer. To ensure normal operation, please restart your system. An error occurs when the system is not restarted after installing MagicTune™. (This is for Win98SE and WinMe only.) Restart the system before use. For the best performance of MagicTune™, adjust to the optimal resolution. Refer to the User Guide for the optimal resolution.
the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magicTune. MagicTune™ doesn't work properly. z z Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magicTune. Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
Overview | Installation | Interface | Uninstall | Troubleshooting Overview What is MagicRotation? Traditionally, computer displays allowed the user to view only in landscape mode. In today's information age, more users need to view documents, web pages, emails, etc. in there day to day life. These types of applications can be better viewed in portrait mode where the entire contents are available on the screen.
Overview | Installation | Interface | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicRotation installation file. 3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicRotation program. 7. Click "Install." 8. The "Installation Status" window appears.
9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly. 10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation. Limitation 1. The "Display Driver" should be properly loaded for the MagicRotation to work properly.
Close the application. Select the Orientation (90, 180, 270) you want to view the application. { Relaunch the application. In most cases this should fix the problem. { { 3. User Applications using OpenGL and DirectDraw (3D drawing) will not function as per the orientation mode selected (90, 180, 270). e.g. 3D games 4. DOS based applications in Full Screen Mode will not function as per the orientation mode selected (90, 180, 270). 5. Dual is not supported in Windows™ 98, ME, NT 4.0. 6.
Overview z z | Installation | Interface | Uninstall | Troubleshooting When Rotation is functioning, portion of MagicTune™ program may not operate normally. AutoRotation : The screens display will automatically rotate when the monitor is rotated. z z z z z To execute Auto Rotation, it should be done as below. Please install both MagicRotation and MagicTune™ 3.6 programs in your computer. Launch MagicTune 3.6 Option → Preference → Click the small box in the enable task tray menu.
Rotate to 90 : Display will be rotated 90 degrees from the current angle. Rotate to 180 : Display will be rotated 180 degrees from the current angle.
Rotate to 270 : Display will be rotated 270 degrees from the current angle. Hot key : Hot Keys are available by default and can be changed by user. It can be assigned by user directly with keyboard after changing the existing HotKey . User can create the hot key with the combination of Shift, Ctrl, Alt and general keys. In case only general key is pressed, it will be assigned in the form of Alt+general key. Help : Shows the HELP of MagicRotation program.
Overview | Installation | Interface | Uninstall | Troubleshooting Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows™ Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add/Remove Programs" icon in Control Panel. 3.
Overview | Installation | Interface | Uninstall | Troubleshooting Troubleshooting Before You Call Technical Support z MagicRotation Software works with the installed "Display Driver" supplied by your Graphic Card Vendor to provide screen rotation capabilities. If the installed "Display Driver" is working incorrectly or has bugs in it, then these bugs would still exist even after MagicRotation Software is installed.
SyncMaster 913N/915N Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? Check the signal cable connection.
mode during this one-minute period. (The message is displayed again if the system is rebooted.) The screen shows strange colors or just black and white. The screen suddenly has become unbalanced. There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
monitor' by searching new Hardware. MagicTune is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune MagicTune™ doesn't work properly. Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune.
Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
SyncMaster 912T/913T/913B/901B Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
85Hz, the display will work properly but the "Not Optimum Mode","Recommanded Mode 1280 x 1024 60Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. press any key on the keyboard to activate the monitor and restore the image on the screen.
have changed after changing the video card. Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel→Display→Settings. * Contact the video card manufacturer for details. How can I set the Power Saving function? Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual).
The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips z A monitor recreates visual signals received from the computer.
General General Model Name SyncMaster 913N LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0,7Vp-p Positive at 75Ω Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Less than 38W Dimensions (WxDxH)/ Weight (Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215.2 x 424.6 mm / 16.4 x 8.5 x 16.7 inch(With Basic Stand) / 5.6 kg Dimensions (WxDxH)/ Weight (Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200.0 x 420.6 mm / 16.4 x 7.9 x 16.6 inch(With Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
General General Model Name SyncMaster 915N LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.294 mm (V) Type a-si TFT active matrix Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16,2M Colors Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0,7Vp-p Positive at 75Ω Separate H/V sync, Composite sync, SOG, TTL level positive or negative.
Less than 38W Dimensions (WxDxH)/ Weight 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215.2 x 424.6 mm / 16.4 x 8.5 x 16.7 inch(With Basic Stand) / 5.6 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
General General Model Name SyncMaster 912T LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.
Less than 38W Dimensions (WxDxH)/ Weight 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200.0 x 420.6 mm / 16.4 x 7.9 x 16.6 inch(With Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
General General Model Name SyncMaster 913T LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.
Less than 38W Dimensions (WxDxH)/ Weight (Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215.2 x 424.6 mm / 16.4 x 8.5 x 16.7 inch(With Basic Stand) / 5.6 kg Dimensions (WxDxH)/ Weight (Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200.0 x 420.6 mm / 16.4 x 7.9 x 16.6 inch(With Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
General General Model Name SyncMaster 913B / 901B LCD Panel Size 19" Diagonal (48 cm) Display area 376.32 mm (H) x 301.056 mm (V) Pixel Pitch 0.294 mm (H) x 0.
Less than 38W Dimensions (WxDxH)/ Weight (Simple Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 215.2 x 424.6 mm / 16.4 x 8.5 x 16.7 inch(With Basic Stand) / 5.6 kg Dimensions (WxDxH)/ Weight (Pivot Stand) 416.6 x 60.2 x 349.4 mm / 16.4 x 2.4 x 13.8 inch (Without Stand) 416.6 x 200.0 x 420.6 mm / 16.4 x 7.9 x 16.6 inch(With Basic Stand) / 7.2 kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Service The address and phone number of the company can be changed without prior notice. CANADA : Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada Tel. 1-800-SAMSUNG (7267864) Fax. (905) 542-1199 http://www.samsung.ca MEXICO : Tel. 01-800-SAMSUNG (7267864) Fax. 01.800.849.1743 http://www.samsung.com/mx U.S.A : Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511 Tel. 1-800-SAMSUNG (7267864) http://www.samsung.
Tel. 0800-124-421 http://www.samsung.com/br CHILE : Samsung Electronics Chile LTDA. Avda. Americo Vespucio Sur 100, Oficina 102 Las Condes, Santiago, Chile Tel. 800-726-7864(SAMSUNG) Fax. 56-2-485-8502 http://www.samsung.com/cl COST RICA : Tel. 0-800-507-7267 http://www.samsung.com/latin ECUADOR : Tel. 1-800-10-7267 http://www.samsung.com/latin EL SALVADOR : Tel. 800-6225 http://www.samsung.com/latin GUATEMALA : Tel. 1-800-299-0013 http://www.samsung.com/latin JAMAICA : Tel. 1-800-234-7267 http://www.
Tel. 38 322 887 http://www.samsung.com/dk FINLAND : Tel. 09 693 79 554 http://www.samsung.com/fi FRANCE : Samsung Service Consommateurs 66 rue des Vanesses BP 50116 - Villepinte -95950 ROISSY cedex France Tel. 08 25 08 65 65 (0,15 /min) Fax. 01 48 63 06 38 (0,15 /min) http://www.www.samsung.fr GERMANY : Samsung Electronics GmbH Samsung House Am Kronberger Hang 6 65824 Schwalbach/Ts. Deutschland Tel. 01805 - 121213 ( 0,12/Min) Fax. 01805 - 121214 ( 0,12/Min) http://www.samsung.de HUNGARY : Tel.
POLAND : Tel. 0 801 801 881 Fax. +48-22-607 4448 http://www.samsung.com/pl PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA, S.A Rua Cesario Verde, no 5-4, Piso 2795-753 Queijas-Portugal Tel. 80 8 200 128 http://www.samsung.pt SLOVAKIA : Tel. 0850 123 989 SPAIN : Tel. 902 10 11 30 http://www.samsung.com/es SWEDEN : Tel. 08 585 367 87 http://www.samsung.com/se U.K : Samsung Electronics U.K. Ltd. Unit C, Stafford Park 12 Telford, Shropshire TF3 3BJ The United Kingdom Tel. 0870 242 0303 Fax.
Tel. 800-810-5858, 010- 6475 1880 http://www.samsungservice.com.cn HONG KONG : Customer Service Center 11/F, Phase 2, MTL warehouse Building, Berth One, Kwai Chung, N.T., Hong Kong Tel. 2862 6001 Fax. 2862 6971 http://www.samsung.com/hk INDIA : 2nd fl CC-28 , Nehru Enclave Kalkaji New Delhi India 110019 Tel. 3030 8282 1600 1100 11 http://www.samsung.com/in INDONESIA : Pusat Pelayanan Purna Jual. PT.SEIN(Samsung Electronics Indonesia) Jl. Raya Pasar Minggu No.34, Jakarta Selatan Tel. 0800-112-8888 Fax.
TAIWAN : Tel. 0800-329-999 http://www.samsung.com/tw VIETNAM : Tel. 1 800 588 889 Fax. (084) 08-8965566 http://www.samsung.com/vn SOUTH AFRICA : Samsung Electronics South Africa (PTY) LTD Unit 5/6, Hi Tech Villiage, Superior Road, Midrand South Africa Tel. 0860 726786 (SAMSUNG) Fax. 27-11-545-6112 http://www.samsung.com/za U.A.E : Tel. 800SAMSUNG (7267864) Fax. 009714 8837714 http://www.samsung.com/mea Terms Dot Pitch The image on a monitor is composed of red, green and blue dots.
For Better Display 1. Adjust computer resolution and screen injection rate (refresh rate) on computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. { { Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
