! ! ! ! SyncMaster 711NT/ 911NT Install drivers Install programs
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire. Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances andwhere it will be operated for 24 hours continuously such as an airport, train station or etc.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Otherwise, this may cause fire. Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire. Put down the monitor carefully. Failing to do so may damage the monitor. Do not place the monitor face down.
The plastic packaging (bag) may cause suffocation if children play with it. Cleaning and Using When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.
cause a malfunction or fire. Others Do not remove the cover (or back). This may cause electric shock or fire. Refer to a qualified servicing company. If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.
This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor. This may cause a malfunction, electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center. Keep the product away from combustible chemical sprays or inflammable substances.
Keep the volume at a comfortable level when using the headphones. Excessively loud volume level may damage hearing. Viewing the monitor continuously at a too close angle may result in damage to your eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury. Proper Seating Posture During Monitor Use Try to maintain a good posture when using the monitor. z z z z z z z Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.
Features What is a network monitor? A network monitor can be used for the same purposes as a common monitor. It also provides the functionalities of most computers, such as an Internet connection, creating documents, editing images, via a connection to the host PC over the LAN. In addition, it allows you to connect an external device (DSC, MP3, external storage media) to the USB port and play music, movies and games. It is a new concept monitor.
Package Contents Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Your Monitor Front MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MagicBright™ button [ ] MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently six different modes are available : Custom, Text, Internet, Game, Sport and Movie. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright™ control button.
For watching motion pictures such as a DVD or Video CD. >> Click here to see an animation clip Volume button [ ] Adjust buttons [ When OSD is not on the screen, push the button to adjust volume. ] Adjust items in the menu. Enter button [ ] / SOURCE button Activates a highlighted menu item. / Push the 'SOURCE', then selects the video signal while the OSD is off.
RS-232C Connection Terminal Connect a RS-232C cable to this terminal. VGA OUT port Connect a monitor to another monitor through a D-Sub cable. Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. For using a locking device, contact where you purchase it. Cable Fix Ring When connecting the cable is finished, fix the cables to the Cable Fix Ring.
Connecting Cables Connecting Cables (When used as a normal monitor) Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. Using the D-sub (Analog) connector on the video card. - Connect the D-Sub Cable to the VGA IN port on the back of your monitor. [VGA IN] Using Macintosh - Connect the monitor and the Macintosh computer using the computer connection cable.
USB (USB Connection Terminal) Connect USB devices such as a mouse, keyboard and external storage devices (DSC, MP3, external storage, etc.). LAN (LAN Connection Terminal) Connect the LAN cable. RS-232C Connection Terminal Connect a RS-232C cable to this terminal. D-sub 15-pin port [VGA OUT] Use it by connecting it to another monitor. (The picture of the main monitor is displayed on the connected monitor.
You can tilt the monitor screen forward to adjust the angle to a particular angle. Swivel stand You can easily adjust the position of the monitor screen from right to left using the rotating stand. Rubber stubs are attached at the bottom of the monitor to help fix it to the installation location. Using Other Stands Attaching a Base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
z z z z z z For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
Connecting a Client Monitor Host PC Hub LAN Cable Monitor Connect the power cord to the power terminal at the back of the monitor. Connect the mouse and the keyboard to the USB ports. Connect the LAN port on the back of the monitor and the hub. Connect the hub and the LAN port of the host PC. The host PC must have an IP address. After connecting the LAN and setting the IP address, you can view the host PC screen on the monitor. Use the VGA IN port to directly connect the monitor to a PC.
Setup Client Monitor The Thin Client Setup Wizard is executed when a thin client is installed for the first time, data are not backed up after update, or the Reset the terminal to factory default settings check box is checked on Control Panel -> System. The Thin Client Setup Wizard helps configure basic settings. The procedure for this is as follows: When starting the system for the first time, the Thin Client Setup Wizard is launched as shown below.
Configure the resolution, the color settings, and the screensaver. Then click Next. Select the shell interface to use with the terminal. Click Next to proceed to the next step.
In the next window, set the other terminal properties and click on Next. For more information on terminal properties, refer to Configuring the Client Monitor Environment. If you want to change any of the settings you have configured, click on Back or click on Finish to complete the Setup Wizard. The thin client then completes the Setup Wizard and restarts the terminal automatically.
Connecting to the Host PC You can add, edit or remove connections using the Terminal Connection Manager (Thin Client Shell) or the icon/menus on the Desktop. However, this function requires administrator privileges. If you logged on as a limited user, the menus for configuring connections are hidden or deactivated. If you click the Add button or the Add New Connection menu on the Terminal Connection Manager, the New Connection window is displayed.
Enter the name that will be displayed in the list on the Terminal Connection Manager (or as a connection icon on the Desktop) and click Next. When you connect to the server, the server’s Desktop is displayed on the monitor, by default. If you want to start an application when connected, enter its name and working directory. Click Next to proceed to the next step. If you want to log on the server automatically when connected, enter user name, password and domain.
Select compression, encryption, and sound options for ICA connection. Enter the information required to pass firewalls or security policies. Microsoft Remote Desktop Clinet Enter a name for the connection and host PC’s name. The name you enter will be displayed in the list on the Terminal Connection Manager (or as a connection icon on the Desktop). You can enter an IP address or DNS name for host PC’s name. Click Next to proceed to the next step.
When connected to the host PC, Window NT Desktop is displayed on the monitor, by default. If you want to start an application when connected, enter its path and file name. Click Next to proceed to the final step. Save the new connection and finish the WTS Connection Wizard. If you want to change settings, select a new setting and click Edit.
General : Displays information such as the connection name and the host PC name when auto login is selected. Display : Configures the screen resolution. Make sure to set a value higher than the minimum value that the computer you want to connect to supports. Local Resources Remote Computer Sound : You can configure the sound so that you can easily identity the connection state.
Local Device : Select one of the external devices which are being connected to the host PC computer you want to connect to. Programs : Specify what is displayed on the first screen when connected. You can select the Desktop or an application program. Experience : You can configure the communications speed between your terminal and the host. You can also share a set of configurations for the host PC with other terminals.
Terminal Connection Manager Connections Tab. ① Connect :Selects the host PC to connect to, or opens an Internet window. ② Shutdown:Icons/Menus on the Desktop (Desktop Shell) : Start > Shut down You can shut down or restart the system. :Icons/Menus on the Desktop (Desktop Shell) : Start>Settings>Control Panel ③ Setup You can configure the settings for the computers contained in the product. For more information, see Configuring the Client Monitor Environment.
in the Configure tab of the Terminal Connection Wizard or close the connection window. The Close button is only activated if the selected connection is being connected. ※ Using shortcut keys when multiple connections are running: Ctrl + Alt + End: Displays either the Terminal Connection Wizard(for Thin Client Shell) or the Desktop(for Desktop Shell). Ctrl + Alt + ↑(or ↓): Allows you to switch to a different connection.
Select a port to use with printer, a printer manufacturer, and printer. If you set the added printer as the default printer, printing is performed with this printer unless you specify a different printer. If you double-click an existing printer icon or click the Open button, the Printer Properties window is displayed, which allows you to change the properties for the printer. Terminal Host PC Client License If you select an item in the list of saved licenses, its content is displayed on the window below.
Network With Network in Control Panel, you can view the list of adapters installed in the terminal. To change the properties of an adapter, click Properties after selecting it. You can change IP address and host PC’s name. System The Terminal Information tab shows manufacturer, product information, OS version, and memory information, etc. You can also reset the terminal to factory defaults.
specified waiting time. You need to restart your terminal to apply Display setting changes. ICA Client Setup If you double-click ICA Client Setup, the Global ICA Client Settings window is displayed. With the Keyboard Shortcuts tab, you can configure shortcut keys. Some shortcut keys are used to control operations of the ICA Connection window, and the remaining are normal Windows shortcuts. If you want to change the default key assignments, select a key from the combo box.
Next, all system settings are saved with the existing values and your terminal is restarted. If you want to configure your terminal with fresh new settings, unselect the ‘Reset the system using the save configuration file’ option and click on Next. The next steps are the same as the steps when setting up your terminal for the first time. Desktop The thin client provides a Desktop Shell and a Thin Client Shell. When selecting a shell and restarting your terminal, it boots up into the selected shell.
1. You can enter basic information using the Terminal Local Account group. The user name is the required item to create a new account. (You cannot use symbolic characters and you can use up to 20 characters. If you want to set a password for an account, set a password within 20 characters long and make sure to confirm your password.) 2. You can allocate connections and configure options using the Connection Manager group.
If you want to apply the login functionality in order to allow access for allowed users only, check the Use login function check box. If you do not check this check box, the selected account is the same with the administrator account. If you check the Use login function check box, the Auto Login and the Set screensaver password check boxes are activated.
4) The automatic rotation function is only available when the monitor is directly connected to a PC. Client monitor does not support the automatic rotation function. 5) Restrictions of the Windows 2000 Server Operating System z z Only Low Color (256 colors) screen quality is supported. You cannot find the USB device connected to the monitor from the host PC.
Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue". This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver…" in the "Driver" tab.
Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Insert the CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced." Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver." and select "Install from a list or." then click the "Next" button. Select "Don't search ,I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button. This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click the "Close" button then click the "OK" button continually.
Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button. How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon.
Click "Start," "Settings," "Control Panel," and then double-click "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency).
Installing the Natural Color Software Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural Color screen will appear. Click on Natural Color in the startup window to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the Windows [Start] button, select [Run...] . Enter D:\Color\NCProSetup.exe and then press the key.
Hardware z z 32MB Memory above 60MB Hard disk space above * For more information, visit the MagicTune™ website. Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows® XP, go to [Control Panel] in the [Start] menu. 2.
Control Buttons [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu. [ ] Press this button to Activates a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
Direct Functions AUTO Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. The values of fine, coarse and position are adjusted automatically. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. AUTO Available in analog Mode Only If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.
In case of pushing MENU button after locking OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the menu button for more than five (5) seconds to activate the OSD adjustment lock function. OSD Lock & Unlock Unlock : Hold down the menu button for more than five (5) seconds to deactivate the OSD adjustment lock function.
MagicBright™ Menu MagicBright™ Description Push the MagicBright™ button to circle through available preconfigured modes.
Volume When OSD is not on the screen, push [▲/ ] the button to adjust volume. SOURCE Menu Description SOURCE Selects the Video signal while the OSD is off.
Menu Brightness Description You can use the on-screen menus to change the brightness according to personal preference. MENU → Contrast → , → MENU You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent.
Menu Description Play/Stop MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. Off Demo Returns to the original mode. The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. Full Displays not only vivid natural color but also more realistic natural skin color with clearness.
Menu Coarse Description Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Available in analog Mode Only MENU → , → → → , → MENU Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). Fine Available in analog Mode Only MENU → Sharpness , → → , → → , → MENU Changes the clearance of image.
OSD Menu Description You can choose one of the nine languages. Language The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → H-Position , → MENU , → → , → → , → MENU , → → , → → , → MENU , → → , → → , → MENU The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Menu Image Reset Description Image parameters are replaced with the factory default values. MENU → Color Reset → → → , → MENU Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.
Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom Check List Solutions No images on the screen. I cannot turn on the monitor. Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? Check the signal cable connection.
on the screen. Is the power indicator on the monitor blinking at 1 second intervals? Press a key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen. I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? Unlock the OSD by pressing the [ ] button for at least 5 seconds.
monitor, Plug & Play (VESA DDC) monitor found". manual to see if the Plug & Play (VESA DDC) function can be supported. Installation Instructions. Problems related to Audio No sound Ensure that the audio cable is firmly connected to both the audio-in port on your monitor and the audio-out port on your sound card. (Refer to Connecting the Monitor) Check the volume level. Sound level is too low. Check the volume level.
and 'Password' of the 'Remote Desktop' with those of the host PC. I cannot access the Internet in the Client screen. 1) Check if the Hub port LED to which the LAN cable is connected blinks. If not, that indicates that the LAN connection is disconnected. In this case, connect using another LAN cable. 2) Check if the settings of the 'Network' tab of 'Settings' have been properly set up. The default setting is "DHCP".
How can I adjust the resolution? Windows XP : Set the resolution at the Control Panel → Appearance and Themes → Display → Settings. Windows ME/2000 : Set the resolution at the Control Panel → Display → Settings. Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP : Set the resolution at the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function at BIOS-SETUP of the computer.
Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.
Specifications General Model Name SyncMaster 711NT LCD Panel Size 17 inch (43 cm ) Display area 337.92 mm (H) x 270.336 mm (V) Pixel Pitch 0.264 mm (H) x 0.264 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1280 x 1024@60 Hz Maximum resolution 1280 x 1024@75 Hz Input Signal, Terminated RGB Analog 0.7 Vp-p ± 5 % separate H/V sync, Composite H/V sync TTL level (V high ≥ 2.0 V, V low ≤ 0.
135 MHz Power Consumption AC 100 - 240 V ~ (+/- 10 %), 50/60 Hz Signal Cable 15pin to 15pin D-sub cable, Detachable Dimensions (W x H x D) / Weight 370.0 x 342.3 x 69 mm / 14.6 x 13.5 x 2.7 inch (Without Stand) 370.0 x 404.3 x 200 mm / 14.6 x 15.9 x 7.9 inch (With Basic Stand), 6.2 Kg / 13.7 (lbs) VESA Mounting Interface 100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.
Photo JPEG,BMP Photo Audio Video MPEG1,WMV MP3, WAV, WMA JPEG, BMP Server Requirement Connect Client No CPU RAM Ethernet OS Minimum SPEC Just can load Server Program P3 400 MHz 64 Mbyte 100 Mbps windows 2003 Server Recommend SPEC 1 P4 1.0 GHz 256 Mbyte 2~4 P4 2.4 GHz 512 Mbyte 100 Mbps windows 2003 Server 5~7 P4 3.0 GHz 1 Gbyte 8~10 P4 3.2 GHz 2 Gbyte The content presented above is the result of testing a specific server.
Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.
Specifications General Model Name SyncMaster 911NT LCD Panel Size 19 inch(48 cm) Display area 376.32 mm(H) x 301.056 mm(V) Pixel Pitch 0.294(H) x 0.294(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75Hz Display Color 16.7 M Resolution Optimum resolution 1280x1024@60 Hz Maximum resolution 1280x1024@75 Hz Input Signal, Terminated RGB Analog 0.7 Vp-p ± 5 % separate H/V sync, Composite H/V sync TTL level (V high ≥ 2.0 V, V low ≤ 0.
135MHz Power Consumption AC 100 - 240 V ~ (+/- 10 %), 50/60 Hz Signal Cable 15pin-to-15pin D-sub cable, Detachable Dimensions (W x H x D) / Weight 416.6 X 375.2 X 74.7 mm / 16.4 x 14.8 x 2.9 inch (Without Stand) 416.6 X 420.9 X 200.0 mm / 16.4 x 16.6 x 7.9 inch (With Stand) / 6.8 Kg / 15.0 (lbs) VESA Mounting Interface 100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.
Photo JPEG,BMP Photo Audio Video MPEG1,WMV MP3, WAV, WMA JPEG, BMP Server Requirement Connect Client No CPU RAM Ethernet OS Minimum SPEC Just can load Server Program P3 400 MHz 64 Mbyte 100 Mbps windows 2003 Server Recommend SPEC 1 P4 1.0 GHz 256 Mbyte 2~4 P4 2.4 GHz 512 Mbyte 100 Mbps windows 2003 Server 5~7 P4 3.0 GHz 1 Gbyte 8~10 P4 3.2 GHz 2 Gbyte The content presented above is the result of testing a specific server.
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Preset Timing Modes Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 4004-0000 http://www.samsung.com/br CHILE 800-SAMSUNG(726-7864) http://www.samsung.
TRINIDAD & TOBAGO 1-800-SAMSUNG(726-7864) http://www.samsung.com/latin VENEZUELA 0-800-100-5303 http://www.samsung.com/latin AUSTRIA 0800-SAMSUNG(726-7864) www.samsung.com/at BELGIUM 02 201 2418 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(726-7864) 08 25 08 65 65 (€ 0,15/Min) http://www.samsung.
KYRGYZSTAN 00-800-500-55-500 RUSSIA 8-800-555-55-55 http://www.samsung.ru UKRAINE 8-800-502-0000 http://www.samsung.ua UZBEKISTAN 8-800-120-0-400 http://www.samsung.uz AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn HONG KONG 3698-4698 http://www.samsung.com/hk INDIA 3030 8282 1800 110011 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom sequentially is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method.
Information in this document is subject to change without notice. © 2007 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 Hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
